Amplifier Specifications; Amplifier Installation - Fusion PowerPlant PP-AM120040 User Manual

AMPLIFIER SPECIFICATIONS

PP-AM300010 (Monoblock)
Class D-Class
Max Power Rating 3000 Watts
Frequency Response 20Hz - 320kHz
Dimensions (mm) 436(L) x 278(W) x 60(H)
Power Ratings 850 Watts RMS per Channel
@ 4 Ohms 1% THD+N
1300 Watts RMS per Channel
@ 2 Ohms 1% THD+N
1500 Watts RMS x 1 Channel
@ 1 Ohms 1% THD+N
PP-AM100010 (Monoblock)
Class D-Class
Max Power Rating 1000 Watts
Frequency Response 20Hz - 320kHz
Dimensions (mm) 386(L) x 278(W) x 60(H)
Power Ratings 400 Watts RMS x 1 Channel
@ 4 Ohms 1% THD+N
620 Watts RMS x 1 Channel
@ 2 Ohms 1% THD+N
PP-AM60020 (2 Channel)
Class Class AB
Max Power Rating 600 Watts
Frequency Response 10Hz - 100kHz
Dimensions (mm) 436(L) x 278(W) x 60(H)
Power Ratings
125 Watts RMS per Channel
@ 4 Ohms 1% THD+N
190 Watts RMS per Channel
@ 2 Ohms 1% THD+N
390 Watts RMS Bridged Channels
@ 4 Ohms 1% THD+N
4 4
PP-AM200010 (Monoblock)
D-Class
2000 Watts
20Hz - 320kHz
436(L) x 278(W) x 60(H)
600 Watts RMS x 1 Channel
@ 4 Ohms 1% THD+N
900 Watts RMS x 1 Channel
@ 2 Ohms 1% THD+N
1000 Watts RMS x 1 Channel
@ 1 Ohms 1% THD+N
PP-AM120040 (4 Channel)
Class AB
1200 Watts
10Hz - 100kHz
546(L) x 278(W) x 60(H)
125 Watts RMS per Channel
@ 4 Ohms 1% THD+N
165 Watts RMS per Channel
@ 2 Ohms 1% THD+N
330 Watts RMS Bridged Channels
@ 4 Ohms 1% THD+N
ACCEPTABLE AMPLIFIER LOADS
Model 4 Ohm
PP-AM120040
YES* 1
PP-AM60020
YES* 1
PP-AM300010
YES
PP-AM200010
YES
PP-AM100010
YES
* 1 Per Channel and Bridged Channel(s), *
NB : PP-AM100010 IS NOT 1 Ohm STABLE

AMPLIFIER INSTALLATION

INSTALLATION WARNING
1. Ensure the 12V lead is disconnected from the battery before you connect any
new equipment.
2. Ensure the mounting location will not interfere with the gas tank, brake lines or
electrical wiring.
3. Ensure the Amplifier is securely fastened to the vehicle to prevent damage in the
event of an accident.
4. Ensure all wiring is protected to avoid pinching or crushing which could result in
damage to the audio system.
5. Ensure the mounting location has sufficient air flow around the amplifier. If the
amplifier is mounted in an enclosed space a 3" fan with ducting should be used
to aid in air flow.
6. Do not mount any amplifier on a subwoofer enclosure as extended exposure to
vibration may cause malfunction of the amplifier.
7. Ensure you use the recommended gauge wire/cable for all amplifier
connections.
Wiring
Ensure the audio system is turned off before making any connections to the amplifier,
speakers or source unit. Failure to do so could result in permanent damage to the
audio system.
When wiring the FUSION amplifier ensure that the cable is protected from sharp
objects and always use rubber grommets when wiring through metal panels. Ensure
all terminals and connections are protected from the vehicle chassis and from each
other as failure to do so could result in permanent damage to the audio system.
2 Ohm 1 Ohm
YES* 2 NO
YES * 2 NO
YES YES
YES YES
YES NO
2 Per Channel ONLY
5