VESTEL LCD Series Manual
  1. Manuals
  2. Brands
  3. VESTEL Manuals
  4. Dishwasher
  5. LCD Series
  6. Manual

VESTEL LCD Series Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

LCD SERIES MANUAL
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LCD Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for VESTEL LCD Series

Summary of Contents for VESTEL LCD Series

  • Page 1 LCD SERIES MANUAL...
  • Page 2 LCD SERIES MANUAL INDEX PAGE ELECTRICAL COMPONENTS PLASTIC COMPONENTS DISASSEMBLY...

  • Page 3: Electrical Components

    LCD SERIES MANUAL 1. ELECTRICAL COMPONENTS 1.1 Circulation Pump • Fırçasız Doğru akım motor • 0 – 3400 RPM aralığı • Sargı değerleri ölçülemez. • Termal koruması yazılım kontrollüdür. • Pompa çıkışı 0 – 80 lt/dk 0 – 400 mbar •...
  • Page 4 LCD SERIES MANUAL 1.3.2 NTC Thermal Protection 83±3 ° C Temperatures; 25°- 5000Ω %±5.0 35°- 3300Ω %±5.5 55°- 1520Ω %±6.5 63°- 1174Ω %±7.5 80°- 670Ω %±8.0 90°- 488Ω %±8.5 1.3.3 Pressure Switch Voltage : 220/240 V : 50 Hz (16 A – 3 Pins) Frequency 1.3.4 Diverter...
  • Page 5 LCD SERIES MANUAL 1.4 Detergent DispenserKabı Detergent Compartment: Main wash compartment : 40 cm³ (25/15) : 5 cm³ Prewash compartment Aid Rinse Departmant: : 150 cm³ Aid rinse cap Factory outlet setting position : 3. seviye Detergent Dispenser Bobbin: Voltage...

  • Page 6: Water Softener

    LCD SERIES MANUAL 1.6 Water Softener 1.6.1 Regeneration Valve; Voltage : 220/240 V Frequency : 50/60 Hz Total Power : 6 W : 4130±٪10 Ω ( 25 Cº ) Resistance Regeneration valve is assembled on the water softener. 1.6.2 Salt Sensör;...
  • Page 7 LCD SERIES MANUAL 1.8 ON/OFF Button; Button is assembled in the control panel unit. On / Off ( two pole ). Voltage : 250 V Currency : 50mA 1.9 Turbo Fan Motor; Total Power : 15 W Voltage : 220/240 V Frequency : 50 Hz.

  • Page 8: Power Cord

    LCD SERIES MANUAL 1.11 Flowmeter ; The amount of water intake is in precise control 1.12 Power Cord; : Euro 3’lü 1 mm2 kesitli, bakır iletkenli Type solation : TS 9760 H05VV-F : TS-IEC 60884–1 topraklı PVC enjeksiyon Plug Length...
  • Page 9 LCD SERIES MANUAL PLASTIC COMPONENTS 2.1 Drain Hose; Drain hose maximum height : 110cm Drain hose minimum height : 50cm Drain hose maximum length : 400cm 2.2 Water Inlet Hose ; Hose that is flat edge is assemblied to plug.

  • Page 10: Salt Container

    LCD SERIES MANUAL 2.4 SALT CONTAINER; It decreases hardness of water that comes from main supply. It includes 2 departments that “salt department” and “recine department” with 2 types that is sensor or without sensor. 2.5 Sump ; Sump that is reservoir connects water in tube with circulation pump and drain pump and heater casing..

  • Page 11: Upper Spray Arm

    LCD SERIES MANUAL 3.7 L Spray Arm; It transfers water from spray arm support to upper spray 2.8 Upper Spray Arm; It tranfers water from L spray arm to upper spray arm There are two hole back of the upper spray arm.

  • Page 12: Lower Spray Arm

    LCD SERIES MANUAL 2.10 LOWER SPRAY ARM; It distributes water from spray arm support to dirty dishes in the lower basket...
  • Page 13 LCD SERIES MANUAL DISASSEMBLY CAUTION!: REMOVE ELECTRIC PLUG FROM THE SOCKET DURING THE DISASSEMBLY 1 ) ACCESSIBILITY 1.1) Top Plate Remove two screws that fix the top plate at the back b) Push the top-plate back and pull it up.
  • Page 14 LCD SERIES MANUAL 1.2 ) Plastic Kick plate a) Remove two screws fixing plastic kick plate b) Remove the plastic kick plate as it is shown in the picture.
  • Page 15 LCD SERIES MANUAL 1.3) Side panels Before removing side panels ; a) Firstly remove the top plate. b) Than remove plastic kick plate.
  • Page 16 LCD SERIES MANUAL 1.4 ) Front Panel a) Remove six screws that fix the front panel. b) Pull down the front panel as it shown in the Picture.
  • Page 17 LCD SERIES MANUAL 1.5 ) Kick Plate Sheet Iron a) Remove top plate, plastic kick plate and side panels. b) Remove two screws tat fix the kick plate sheet iron. c) Pull it down as shown in the picture. 1.6 Control Panel...
  • Page 18 LCD SERIES MANUAL 1.7 ) Electronic Card a) Remove the wires that are shown in the picture.
  • Page 19 LCD SERIES MANUAL WARNING: WHILE REMOVING WIRES, DO NOT PULL THEM FROM WIRES, PULL FROM THE CONNECTOR. b)Remove pcb box cover with pulling its plastic hinges. c) Remove the wire which is between rotary switch and electronic card.
  • Page 20 LCD SERIES MANUAL d) Remove the electronic card from pcb box by removing pcb box’s plastic hinges. 1.8 ) Door Lock Group a) Remove control panel group. b) Remove two screws that fix the door lock group..
  • Page 21 LCD SERIES MANUAL 1.9 ) Dispenser a) Remove the front panel b) Remove the wire. c) Remove dispenser from inside door‘s hinges by using slotted screwdriwer. d) Push and remove the dispenser .
  • Page 22 LCD SERIES MANUAL WARNING: USE WORK GOVERS OTHERWISE INSIDE DOOR SHEET IRON CAN CUT YOUR HANDS 1.10 ) Door Inside ve Hinge Cord Group a) Remove side panels. b) Remove hinge spring from hinge cord group as it is shown in the picture.
  • Page 23 LCD SERIES MANUAL THE INNER COMPONENTS 2. ) To Access The Components From Sides Remove the side panel to reach component which you need a) Right Sight b) Left Sight...
  • Page 24 LCD SERIES MANUAL 2.1) TURBO FAN MOTOR GR a) Last right sıde panel b) Remove the two screws on the bottom of the fan is connected to the base turbo c) Remove the turbo fan on the condensing unit...
  • Page 25 LCD SERIES MANUAL 2.1 ) NTC with Thermal Protector a) Remove turbofan new.NTC will see at the top of the heater group b) Remove the power cord is connected. (NTC on the left, on the right is the thermal protection...
  • Page 26 LCD SERIES MANUAL c) Pull yourself under the NTC pin. d) NTC 't pull it toward you out of the anchorage.
  • Page 27 LCD SERIES MANUAL 2.2 ) Air-Break ) Remove the left side panel of the machine. b) Open machine’s door.. c) Rotate counterclockwise air-break nut and remove d) Remove air –break’s connections with salt cap as it is shown in the picture.( Be careful about plastic hinges )
  • Page 28 LCD SERIES MANUAL 2.3 ) Hose Connection Plastic a) Remove left side panel. b) By using flat tip screwdriver remove hose connection plastic’s hinge from the basement as it shown in the picture. c) Push the hose connection plastic.
  • Page 29 LCD SERIES MANUAL WARNING: IF YOU DO NOT OBEY INSTRUCTIONS WHILE DISASSEMBLY OF THE HOSE CONNECTION PLASTIC IT CAN BE BROKEN 2.4 ) Supply Cable a )Remove the plastic hose connecting the lower base. a) Remove the bottom cover. b) Supply cord with noise filter of electrically disconnect.
  • Page 30 LCD SERIES MANUAL e ) Besleme kablosunu bulunduğu yerden sökün. 3. To Access The Components From in Front Of The Machine a) Remove Plastic kick plate and .kick plate iron. 3.1 ) Regeneration Valve a) Remove plastic kick plate and. Kick plate iron sheet.
  • Page 31 LCD SERIES MANUAL 3.2) Drain Pump a) Remove Plastic kick plate and .kick plate iron sheet. b) Remove the wires... c) To remove the drain pump that fixes to the sump, rotate it in the direction of counterclockwise and pull .
  • Page 32 LCD SERIES MANUAL 4. To Access The Components from the Lover Cover a) a) Lay the appliance on the rear panel.. b)Remove lower cover from the places that are shown in the picture.
  • Page 33 LCD SERIES MANUAL 4.1 ) Circulation Pump a) Lay the appliance on the rear panel. b) Remove the electrical connection on the circulation pump. c) Remove 2 clamps that are shown in the picture (Heater casing- circulation pump, sump-Circulation pump)
  • Page 34 LCD SERIES MANUAL 4.2 ) Isıtıcı (Heater-Casing Grubu) a) Remove the machine’s lower cover. b) Remove five screws that fix heater to sump c) Remove the electrical connection.
  • Page 35 LCD SERIES MANUAL 4.3 ) Water Softener a) To remove salt cup cover, rotate it in the direction of counterclockwise. b) To remove salt cup nut , rotate it in the direction of counterclockwise . c) Remove left side panel d) Detach the connections which are between water softener and air-break.
  • Page 36 LCD SERIES MANUAL 4.4) Parazit Filtresi a) Remove lower cover. b) Remove one screw fixing parasite filter. c)Remove the electrical connection of noise filter. d)Remove the electrical connection of noise filter.
  • Page 37 LCD SERIES MANUAL 4.5 ) Floater a) Lay the bottom of the machine and remove the cover. b) Floater sub-base screws (2 pcs) Unscrew the anticlockwise. c) Disconnect the overflow hose float. d) Disconnect the electrical connection.
  • Page 38 LCD SERIES MANUAL 4.6 ) Water Inlet valve a) Remove lower cover. b) Electricity connection and water inlet valve connects the air-break disconnect hose. c) The water inlet valve is connected by pulling back after recovering from the pins clockwise to remove.
  • Page 39 LCD SERIES MANUAL a)Remove the hose connection plastic b)Remove lower cover. c)Remove the clamp that fixes draining hose to the sump. d)Remove draining hose.. 4.8 ) Led Modül Remove the electrical connections as in the a) Remove the right side panel.
  • Page 40 LCD SERIES MANUAL 5 ) Basket Group 5.1 ) Lower Basket a) Open machine’s door. b) Pull the basket to yourself. whells 5.2) Upper Basket a) Open machine’s door. b) Pull the basket to yourself.
  • Page 41 LCD SERIES MANUAL c) The plastic cover on top rail (top rail lock Cart- front) right by turning it to the left to the right and the left. d) Cart pulling it toward you recover from the rails. 5.3 Third cart a) Open the cover of the machine.
  • Page 42 LCD SERIES MANUAL c) The plastic cover on top rail (top rail lock Cart- front) right by turning it to the left to the right and the left. d) Cart pulling it toward you recover from the rails. 5.3 Basket Rails...
  • Page 43 LCD SERIES MANUAL 6.1 ) Course , Micro and metal filters a)Open the door. b)Remove lower basket. c) To remove microfilter group rotate them in the direction of counterclockwise and pull them up as it is shown in the Picture.
  • Page 44 LCD SERIES MANUAL f) To remove the basket rails, open the door and take out baskets. g) To remove basket rails release the rail from upper basket stopper rear.. 6.2 ) Sprinkler System a)After removing the lower basket , pull the spray...
  • Page 45 LCD SERIES MANUAL b)To remove upper spray arm adjustment link pull it trought yourself as it is shown in the picture. c) To remove upper spray feeding canal turn left it than pull it up as it is shown in the picture.
  • Page 46 LCD SERIES MANUAL e) From inside tub ,remove the basket and lower spray arm . f) Remove the microfilter group and metal filter . g) Remove the four screws that secure the tumb to the tub h) Remove the two screws which secure the spray arm support to the sump.
  • Page 47 LCD SERIES MANUAL ELECTRICAL TERMS AND ABBREVIATIONS the FLOWMETRE NTC SENSÖR SU GİRİŞ VALFİ FLOATER SENSÖRÜ BOŞALTMA POMPASI BASINÇ ANAHTARI KAPI SWITCH DETERJAN ÇEKMECESİ ISITICI YIKAMA MOTORU KAPASİTÖR REJENERASYON VALFİ ISITMA GÜVENLİK...

  • Page 48: Repair Techniques

    LCD SERIES MANUAL REPAIR TECHNIQUES COMPONENTS AND RESISTANCE VALUES COMPONENTS REAL VALUES NOTES 0 Ω ON/OFF button is pressed on component ON / OFF BUTTON CN2.9 – CN2.2 0 Ω Door is close DOOR SWITCH (KAPI KİLİDİ) CN2.10 – CN2.2 0 Ω...
  • Page 49 LCD SERIES MANUAL You might measure the components either connentors of electronic card or directly on the component. Measuring from the connectors of electronic card gives definite results to define the repair. If you know the specialities and values of tester, you can easily determine the repair.

  • Page 50: Drain Pump

    LCD SERIES MANUAL UYARI: Değişken devirli yıkama pompasının ölçümü yapılamaz. Drain Pump: From the Electronical Card: 143 ± 7 on the connectors CN2.2 – CN2.4 From the component : Probes of the tester should be applied on to the related connectors as shown on the pictures...

  • Page 51: Water Inlet Valve

    LCD SERIES MANUAL Water inlet valve:...
  • Page 52 LCD SERIES MANUAL From the Electronical Card: 3750 ± 10 Ω ( 20 Cº) on the connectors CN2.6 – CN 2.9 Above sketch show the connectors of the water inlet valve on the electronical card. Probes of the tester should be applied on to the related connectors.
  • Page 53 LCD SERIES MANUAL...

  • Page 54: Detergent Dispenser

    LCD SERIES MANUAL Heater Casing: It can’t be measured from the electronical card. From the component: 23.95 ±15 Ω Probes of the tester should be applied on to the related connectors as shown on the pictures. Detergent Dispenser: It can’t be measured from the electronical card.
  • Page 55 LCD SERIES MANUAL Probes of the tester should be applied on to the related connectors as shown on the pictures Regenaration Valve: From the Electronical Card: 4130 ± 10 (25 C º) on the connectors CN2.10 – CN2.7 Above sketch show the connectors of the regeneration valve on the electronical card. Probes of the tester should be applied on to the related connectors.

  • Page 56: Pressure Switch

    LCD SERIES MANUAL Pressure Switch: From the Electronical Card: CN2.10 – CN2.2 0 Ω There is water (Full) Ω There is not water (Empty) Above sketch show the connectors of the pressure switch on the electronical card. Probes of the tester should be applied on to the related connectors.

  • Page 57: Ntc Sensor

    LCD SERIES MANUAL NTC sensor: From the Electronical Card: Above sketch show the connectors of NTC sensor on the electronical card. Probes of the tester should be applied on to the related connectors. From the component: Diverter: From the Electronical Card:...
  • Page 58 LCD SERIES MANUAL Sketch above show the connectors of the diverter on the electronical card. Probes of the tester should be applied on to the related connectors. From the component: Probes of the tester should be applied on to the related connectors as shown on the pictures.
  • Page 59 LCD SERIES MANUAL Position 1: You can check the floater by controlling the specified value intervals. Position 2: If failure code is occured related with the floater within control the above values; you can figure out whether leakage occurs or not.

  • Page 60: Door Switch

    LCD SERIES MANUAL Door Switch : From the Electronical Card: 0 Ω on the connectors CN2.9 – CN2.2 ( Door is close ) Above sketch show the connectors of the door switch on the electronical card. From the component: Probes of the tester should be applied on to the related connectors as shown on the pictures.

  • Page 61: Fan Motor

    LCD SERIES MANUAL Fan Motor: From the Electronical Card: 238.6 Ω ± % 5 on the connectors CN 6.2 – CN 2.9 Above sketch shows the connectors of the fan motor on tke electronical card. From the component : Probes of the tester should be applied on to the related...
  • Page 62 LCD SERIES MANUAL connectors as shown on the pictures. Rinse Aid Sensor: From the Electronical Card: Above sketch shows the connectors of the rinse aid sensor on tke electronical card. From the component : Probes of the tester should be applied on to the related connectors as shown on the pictures.

  • Page 63: Salt Sensor

    LCD SERIES MANUAL Salt Sensor: From the Electronical Card: CN5.1 – CN5.2 0 Ω NO SALT ∞ Ω THERE IS SALT Sketch above show the connectors of the salt sensor on the electronical card. Probes of the tester should be applied on to the related connectors.

  • Page 64: On/Off Button

    LCD SERIES MANUAL On/Off Button: It can’t be measured from the electronical card From the component: 0 Ω When the buton is pressed Service Failure Codes Coding Service Failure for T11: Name Wash Notes Overflow / Leakage Blink Blink In the normal work only leakage is visualized.
  • Page 65 LCD SERIES MANUAL Coding service failure for T12,T13,T21: DİSPLAY Name Notes Oferflow In the normal work this failure is not visualized. Leakage Draining time out Presence of flow meter impulses Absence of flow meter In the normal work this failure is not visualized.

Table of Contents