Page 1
SERVICE MANUAL COLOR TELEVISION/ DVD VIDEO PLAYER MD30H82 The above model is classified as a green product (*1), as indicated by the underlined serial number. This Service Manual describes replacement parts for the green product. When repairing this green product, use the part(s) described in this manual and lead-free solder (*2).
Hazardous Substances. From July 1, 2006, the RoHS Directive will prohibit any marketing of new products containing the restricted substances. Increasing attention is given to issues related to the global environmental. Toshiba Corporation recognizes environmental protection as a key management tasks, and is doing its utmost to enhance and improve the quality and scope of its environmental activities.
All manuals and user guides at all-guides.com CAUTION THIS DIGITAL VIDEO PLAYER EMPLOYS A LASER SYSTEM. TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS SERVICE MANUAL CARE- FULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTENANCE, CONTACT AN AUTHORIZED SERVICE LOCATION-SEE SERVICE PROCEDURE.
All manuals and user guides at all-guides.com SERVICING NOTICES ON CHECKING 1. KEEP THE NOTICES 6. AVOID AN X-RAY As for the places which need special attentions, Safety is secured against an X-ray by consider- they are indicated with the labels or seals on the ing about the cathode-ray tube and the high cabinet, chassis and parts.
All manuals and user guides at all-guides.com IMPORTANT SAFEGUARDS READ INSTRUCTIONS All the safety and operating instructions should be read before the unit is operated. RETAIN INSTRUCTIONS The safety and operating instructions should be retained for future reference. HEED WARNINGS All warnings on the unit and in the operating instructions should be adhered to.
Page 6
All manuals and user guides at all-guides.com IMPORTANT SAFEGUARDS (CONTINUED) OUTDOOR ANTENNA GROUNDING If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
Page 7
All manuals and user guides at all-guides.com IMPORTANT SAFEGUARDS (CONTINUED) EXAMPLE OF ANTENNA GROUNDING AS PER THE NATIONAL ELECTRICAL CODE ANTENNA LEAD IN WIRE GROUND CLAMP ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMPS POWER SERVICE GROUNDING NEC-NATIONAL ELECTRICAL CODE...
Page 8
All manuals and user guides at all-guides.com WHEN REPLACING DVD DECK [ When removing the DVD Deck ] Before removing Pick Up PCB and DVD MT PCB connector, the short circuit the position shown in Fig. 1 using a soldering iron. If you remove the DVD Deck with no soldering, the Laser may be damaged. [ When installing the DVD Deck ] Remove all the soldering on the short circuit position after the connection of Pick Up PCB and DVD MT PCB connector.
All manuals and user guides at all-guides.com DISC REMOVAL METHOD AT NO POWER SUPPLY Remove the Back Cabinet and AV PCB/DVD Block. (Refer to item 1 of the DISASSEMBLY INSTRUCTIONS.) Rotate the Main Gear in the direction of the arrow by hand. (Refer to Fig.
All manuals and user guides at all-guides.com TABLE OF CONTENTS GREEN PRODUCT PROCUREMENT ..................A1-1 LEAD-FREE SOLDER ......................A1-1 CAUTION ..........................A1-2 SERVICING NOTICES ON CHECKING .................. A1-3 HOW TO ORDER PARTS ....................... A1-3 IMPORTANT SAFEGUARDS ....................A1-4~A1-6 WHEN PERLACING DVD DECK .................... A1-7 DISC REMOVAL METHOD AT NO POWER SUPPLY ............
All manuals and user guides at all-guides.com GENERAL SPECIFICATIONS CRT Size / Visual Size 30 inch / 760mmV System CRT Type Flat (16:9) Magnetic Field BV/BH + 0.45 G / 0.18 G Color System NTSC Display Capability 1080i/540p Speaker 2 Speaker Position Front Size...
Page 12
All manuals and user guides at all-guides.com GENERAL SPECIFICATIONS Signal Video Signal Input Level 1 V p-p/75 ohm Output Level S/N Ratio (Weighted) at DVD Mode S/N Ratio (Weighted) at VCR Mode Horizontal Resolution at DVD Mode Horizontal Resolution at VCR(SP)Mode RGB Signal Output Level Audio Signal...
Page 13
GENERAL SPECIFICATIONS G-11 Remote Unit RC-MN Control Glow in Dark Remocon Unit Remocon Format TOSHIBA Format TOSHIBA Custom Code 40-BF H, 44-BB H, 45-BA H, 45-BC H Power Source Voltage(D.C) UM size x pcs UM-4 x 2 pcs Total Keys...
Page 14
All manuals and user guides at all-guides.com GENERAL SPECIFICATIONS G-12 Features Auto Head Cleaning (TV/VCR) VIDEO PLUS+(SHOWVIEW,G-CODE) Forward / Reverse Picture Search Index Search SQPB CM Skip(30sec x 6 Times) Zero Return End Call TV Monitor Program Extend Picture Brightness , Contrast , Color, Sharpness Tint Mode (Picture Preference) Color Temperature...
Page 15
All manuals and user guides at all-guides.com GENERAL SPECIFICATIONS HDMI Input VGA (640x480) Yes (60Hz) 720x480i (4:3) Yes (60Hz) 720x480i (16:9) Yes (60Hz) 720x480p (4:3) Yes (60Hz) 720x480p (16:9) Yes (60Hz) 720x576i (4:3) 720x576i (16:9) 720x576p (4:3) 720x576p (16:9) 1280x720p Yes (60Hz) 1920x1080i Yes (60Hz)
Page 16
All manuals and user guides at all-guides.com GENERAL SPECIFICATIONS G-13 Accessories Owner's Manual Language English w/Guarantee Card Remote Control Unit Battery UM size x pcs UM-4 x 2 pcs OEM Brand Rod Antenna Poles Terminal Loop Antenna Terminal U/V Mixer 300 ohm to 75 ohm Antenna Adapter Antenna Change Plug DC Car Cord (Center+)
Page 17
1 Corner / 2 Edges / 4 Surfaces Height (cm) 40(ORION SPEC:25) Container Stuffing(40' container) Sets G-18 Material Cabinet Front 94V0 DECABROM Rear 94V0 NON-DECABROM Non-Halogen Demand Eyelet Demand G-19 Environment Environmental standard requirement (by buyer) Green procurement of TOSHIBA Pb-free Phase3(Phase3A) Measures for Whisker A3-7...
All manuals and user guides at all-guides.com DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF MECHANICAL PARTS 1-3: AV/POWER/DVD BLOCK (Refer to Fig. 1-3) Remove the 2 screws 1. AND P.C. BOARDS Disconnect the following connectors: 1-1: BACK CABINET (Refer to Fig. 1-1) (CP303, CP404, CP6402 and CP5902).
Page 19
All manuals and user guides at all-guides.com DISASSEMBLY INSTRUCTIONS 1-5: TV MT PCB (Refer to Fig. 1-5) 1-7: OPERATION PCB (Refer to Fig. 1-7) Remove the 2 screws 1. Remove the 4 screws 1. Remove the 2 screws 2. Remove the Angle PCB in the direction of arrow (A). Disconnect the following connector: (CP2201).
Page 20
All manuals and user guides at all-guides.com DISASSEMBLY INSTRUCTIONS 1-9: DVD MT PCB/DVD DECK (Refer to Fig. 1-9) NOTE Before your operation, please read “PREPARATION OF Short circuit the position shown in Fig. 1-9 using a SERVICING”. soldering iron. If you remove the DVD Deck with no Use the Lead Free solder.
Page 21
All manuals and user guides at all-guides.com DISASSEMBLY INSTRUCTIONS 1-11: AV PCB (Refer to Fig. 1-11) Remove the screw 1. Remove the screw 2. Remove the 7 screws 3. Remove the 2 screws 4. Remove the AV Jack Shield. Remove the AV PCB in the direction of arrow. AV PCB AV Jack Shield Bottom Plate...
All manuals and user guides at all-guides.com DISASSEMBLY INSTRUCTIONS 2. REMOVAL OF DVD DECK PARTS NOTE 1. Do not disassemble the DVD DECK PARTS except listed parts here. Minute adjustments are needed if the Main Frame Ass'y disassemble is done. If the repair is needed except listed parts, replace the DVD MECHA ASS'Y.
Page 23
All manuals and user guides at all-guides.com DISASSEMBLY INSTRUCTIONS 2-3: LOADING MOTOR PCB ASS'Y/ LOADING BELT (Refer to Fig. 2-3-A) Pulley Gear Rack Loading Remove the Loading Belt. Remove the screw 1. Main Gear Remove the 2 screws 2. Remove the Loading Motor PCB Ass'y. Main Frame Ass’y Remove the Pulley Gear.
Page 24
All manuals and user guides at all-guides.com DISASSEMBLY INSTRUCTIONS 2-6: TRAVERSE HOLDER/INSULATOR (F)/INSULATOR NOTE (R) (Refer to Fig. 2-6-A) When pushing the Rack Feed in the direction of the Remove the Traverse Holder. arrow, it should be restored to the original position by the Remove the 2 Insulator (F).
Page 25
All manuals and user guides at all-guides.com DISASSEMBLY INSTRUCTIONS 2-8: FFC WIRE HANDLING When installing the FFC, fold it correctly and install it as shown from Fig. 2-8-A to Fig. 2-8-C. NOTE Do not make the folding lines except the specified positions for the FFC.
All manuals and user guides at all-guides.com DISASSEMBLY INSTRUCTIONS 3. REMOVAL OF ANODE CAP 3. After one side is removed, pull in the opposite direction to remove the other. Read the following NOTED items before starting work. NOTE After turning the power off there might still be a potential Take care not to damage the Rubber Cap.
All manuals and user guides at all-guides.com DISASSEMBLY INSTRUCTIONS 4. REMOVAL AND INSTALLATION OF FLAT 3. When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using PACKAGE IC a tweezers and remove the IC by moving with the IC REMOVAL desoldering machine.
Page 28
All manuals and user guides at all-guides.com DISASSEMBLY INSTRUCTIONS INSTALLATION 4. When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thin- 1. Take care of the polarity of new IC and then install the tip Soldering Iron. (Refer to Fig. 4-8.) new IC fitting on the printed circuit pattern.
All manuals and user guides at all-guides.com KEY TO ABBREVIATIONS Audio/Control H.P.F High Pass Filter Automatic Color Control H.SW Head Switch Audio Erase Hertz Automatic Frequency Control Integrated Circuit Automatic Fine Tuning Intermediate Frequency AFT DET Automatic Fine Tuning Detect Indicator Automatic Gain Control Inverter...
Page 30
All manuals and user guides at all-guides.com KEY TO ABBREVIATIONS Serial Strobe Switch SYNC Synchronization SYNC SEP Sync Separator, Separation Transistor TRAC Tracking TRICK PB Trick Playback Test Point UNREG Unregulated Volt Voltage Controlled Oscillator Video Intermediate Frequency Vertical Pulse, Voltage Display V.PB Video Playback Variable Resistor...
All manuals and user guides at all-guides.com SERVICE MODE LIST This unit is provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter to the SERVICE MODE function, press and hold both buttons simultaneously on the main unit or on the main unit and on the remote control for more than the standard time (second).
All manuals and user guides at all-guides.com RE-WRITE FOR DIGITAL SOFT FIRMWARE JG176 USA HD DTV ROM DISC Ref. No. Part No. Parts Name Remarks USA HD DTV ROM JG176 APJG176105 Up-Date of the Firmware DISC NOTE: The operating manual for Re-writing is included in USA HD DTV ROM DISC (JG176). Prepare the following tools for Up-Date of the Firmware.
All manuals and user guides at all-guides.com WHEN REPLACING EEPROM (MEMORY) IC CONFIRMATION OF CHECK SUM, POWER ON TOTAL HOURS, MICON VERSION AND DIGITAL TV MICON FIRMWARE Initial total of MEMORY IC, POWER ON total hours, MICON VERSION and Digital TV MICON Firmware can be checked on the screen.
Page 34
All manuals and user guides at all-guides.com WHEN REPLACING EEPROM (MEMORY) IC CONFIRMATION OF INITIAL DATA If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to ensure correct data settings while making reference to TABLE 1. INIT A7 AA AD B0 B5 D4 D5...
Page 35
All manuals and user guides at all-guides.com ELECTRICAL ADJUSTMENTS BEFORE MAKING ELECTRICAL FUNCTION FUNCTION FUNCTION ADJUSTMENTS OSD H CORNER R-Y PHASE CUT OFF C.PARA G-Y GAIN H.POSI C.SAW G-Y PHASE Read and perform these adjustments when repairing the V.POSI V.SYMM BRI.CENT circuits or replacing electrical parts or PCB assemblies.
All manuals and user guides at all-guides.com ELECTRICAL ADJUSTMENTS 2-3: OSD POSITION 2-5: VERTICAL CENT/ VERTICAL SIZE Receive the monoscope pattern from the Pattern Receive the monoscope pattern. Generator. Press the MENU button. And, then press the LEFT/ Using the remote control, set the brightness and RIGHT button on the remote control until the PICTURE contrast to normal position.
Page 37
All manuals and user guides at all-guides.com ELECTRICAL ADJUSTMENTS 2-7: BRIGHT CENT 2-9: E/W PARA Receive the monoscope pattern. (RF Input) Receive the crosshatch signal from the Pattern Generator. Set the screen mode to FULL. Set the screen mode to FULL. Using the remote control, set the brightness and contrast Using the remote control, set the brightness and contrast to normal position.
Page 38
All manuals and user guides at all-guides.com ELECTRICAL ADJUSTMENTS 2-12: CENSOR SAW Receive the crosshatch signal from the Pattern Generator. Press the MENU button. And, then press the LEFT/ RIGHT button on the remote control until the PICTURE menu appears. Press the UP/DOWN button on the remote control to highlight DISPLAY FORMAT.
Page 39
All manuals and user guides at all-guides.com ELECTRICAL ADJUSTMENTS 2-16: Confirmation of Fixed Value (step No.) Please check if the fixed values of the each adjustment items are set correctly referring below. FUNCTION HD-MI DIGITAL V.POSI V-EHT H-EHT V-BLK P V.BLK S V.LIMIT V.CORR...
Page 40
All manuals and user guides at all-guides.com ELECTRICAL ADJUSTMENTS 3-3: STATIC CONVERGENCE 3. PURITY AND CONVERGENCE ADJUSTMENTS NOTE Adjust after performing adjustments in section 3-2. NOTE Receive the crosshatch pattern from the color bar Turn the unit on and let it warm up for at least 30 generator.
Page 41
All manuals and user guides at all-guides.com ELECTRICAL ADJUSTMENTS 4. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION) AC IN VM COIL PCB POWER PCB CD1710 CRT PCB TP805 S110 S107 CP805 CP804 J801 S108 S109 TP806 CP803 CP1707 CP808B CP1710 CP801 CP851B CP802B...
All manuals and user guides at all-guides.com DVD DECK EXPLODED VIEW Cannot supply by a unit. M2603 PCB610 (LOADING MOTOR PCB ASS'Y) CD2302 CD2301 PCB640 CD2001 (SW PCB ASS'Y) Do not replace the parts. Because, minute adjustments are needed if this condition is disassembled further more.
All manuals and user guides at all-guides.com ELECTRICAL REPLACEMENT PARTS LIST Location No. TSB P/N Reference No. Description RESISTORS ! R356 72797922 R3X28B2R2J R,METAL OXIDE 2.2 OHM 3W ! R401 72783828 R4K1T4222F R,METAL 2.2K OHM 1/4W ! R403 72781717 R4K1T4183F R,METAL 18K OHM 1/4W ! R405...
Page 50
All manuals and user guides at all-guides.com ELECTRICAL REPLACEMENT PARTS LIST Location No. TSB P/N Reference No. Description CAPACITORS ! C1733 72797363 E02L01222M 2200 UF 10V C3025 72797362 E02L01102M 1000 UF 10V C6405 72797090 C03L0R7W2K 820 PF 2KV R ! C6406 72797115 C13HB07H3K 0.0022UF 2KV B...
Page 51
All manuals and user guides at all-guides.com ELECTRICAL REPLACEMENT PARTS LIST Location No. TSB P/N Reference No. Description DIODES D1701 72794491 D1VT001330 DIODE,SILICON 1SS133T-77 ! D1702 72797313 D6CE24110A DIODE,VARISTA ENE241D-10A-Q6 ! D1703 72783759 D4AT01H3E0 DIODE,RECTIFIER 1H3-E D1704 72794491 D1VT001330 DIODE,SILICON 1SS133T-77 D1706 72794491...
Page 52
All manuals and user guides at all-guides.com ELECTRICAL REPLACEMENT PARTS LIST Location No. TSB P/N Reference No. Description DIODES ! D6418 72783906 D2LXSR2900 DIODE,SCHOTTKY SR290-F ! D6419 72783906 D2LXSR2900 DIODE,SCHOTTKY SR290-F D6420 72794481 D97U09R11B DIODE,ZENER MTZJ9.1B T-77 ! D6421 72783412 D2CF2016J0 DIODE,SILICON FE201-6J14...
Page 53
All manuals and user guides at all-guides.com ELECTRICAL REPLACEMENT PARTS LIST Location No. TSB P/N Reference No. Description TRANSISTORS Q601 72795479 T8RA030520 TRANSISTOR,SILICON 2SC3052-T1 Q602 72795481 T6RA015300 TRANSISTOR,SILICON 2SA1530A-T1 Q603 72795479 T8RA030520 TRANSISTOR,SILICON 2SC3052-T1 Q604 72795479 T8RA030520 TRANSISTOR,SILICON 2SC3052-T1 Q605 72795479 T8RA030520 TRANSISTOR,SILICON...
Page 54
All manuals and user guides at all-guides.com ELECTRICAL REPLACEMENT PARTS LIST Location No. TSB P/N Reference No. Description TRANSISTORS Q4203 72795479 T8RA030520 TRANSISTOR,SILICON 2SC3052-T1 Q4204 72795481 T6RA015300 TRANSISTOR,SILICON 2SA1530A-T1 Q4205 72795481 T6RA015300 TRANSISTOR,SILICON 2SA1530A-T1 Q4206 72795481 T6RA015300 TRANSISTOR,SILICON 2SA1530A-T1 Q6401 72794578 TAATA12660 TRANSISTOR,SILICON...
Page 55
All manuals and user guides at all-guides.com ELECTRICAL REPLACEMENT PARTS LIST Location No. TSB P/N Reference No. Description JACKS J4201 72794518 060J431020 RCA JACK MSP-213V2-432_NI_LF J4202 72795493 060J411032 RCA JACK MSP-213V1-652_NI_LF J4203 72783797 063Y700014 JACK DIN-409B J4204 72798996 060J431022 RCA JACK MSP-213V2-732_NI_LF J4205 72783798...
Page 56
All manuals and user guides at all-guides.com ELECTRICAL REPLACEMENT PARTS LIST Location No. TSB P/N Reference No. Description MISCELLANEOUS B3406 72783358 024HC16014 CORE,BEADS HCB3216KF-601T20 B3407 72783358 024HC16014 CORE,BEADS HCB3216KF-601T20 B3408 72783358 024HC16014 CORE,BEADS HCB3216KF-601T20 B3410 72783358 024HC16014 CORE,BEADS HCB3216KF-601T20 B3601 72783357 024HC51513 CORE,BEADS...
Page 57
All manuals and user guides at all-guides.com ELECTRICAL REPLACEMENT PARTS LIST Location No. TSB P/N Reference No. Description MISCELLANEOUS CD4002 72783749 06CH2D4001 CORD,CONNECTOR CH2D4001 CD8101 72783755 122H0C1801 CORD,JUMPER 2H0C1801 CP1704 72796825 069W01001A CONNECTOR PCB SIDE 003P-2100 CP1706 72796825 069W01001A CONNECTOR PCB SIDE 003P-2100 ! CP1707 72796813...
Page 58
All manuals and user guides at all-guides.com ELECTRICAL REPLACEMENT PARTS LIST Location No. TSB P/N Reference No. Description MISCELLANEOUS X101 72796062 100DA32R01 CRYSTAL DT-26 X103 72799226 100WT01611 CRYSTAL HC-49/U-S X603 72781949 1002R01502 CERAMIC OSCILLATOR CSBLA503KECZF30-B0 X2401 72783833 100DT05501 CRYSTAL SMD-49 X2402 72783834 100DT02503...
Page 59
All manuals and user guides at all-guides.com TOSHIBA CORPORATION 1-1, SHIBAURA 1-CHOME, MINATO-KU, TOKYO 105-8001, JAPAN...