HighPoint SSD7103 Installation Manual
Nvme raid controller
Hide thumbs
Also See for SSD7103:
- Installation manual (15 pages) ,
- Quick installation manual (9 pages) ,
- Installation manual (11 pages)
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for HighPoint SSD7103
Summary of Contents for HighPoint SSD7103
- Page 1 SSD7103 Linux Debian10.3.0 Installation Guide HighPoint NVMe RAID Controller SSD7103 Linux Debian 10.3.0 Installation Guide Version 1.0 Copyright © 2019 HighPoint Technologies, Inc. All rights reserved. Last updated on April 3, 2020...
-
Page 2: Table Of Contents
SSD7103 Linux Debian10.3.0 Installation Guide Table of Contents 1 Overview ............................1 2 Installing Linux Debian on SSD7103 controller ................ 1 Step 1 Prepare Your Hardware for Installation ................. 1 Step 2 Check System EFI Settings .................... 1 Step 3 Flash UEFI Rom to SSD7103 ..................3 Step 4 Create Array ........................ -
Page 3: Overview
SSD7103 only support EFI boot. If you have other SCSI adapters installed, you must make sure the SSD7103 controller EFI will be loaded firstly. If not, try to move it to another PCI slot. Otherwise you may be unable to boot up your system. - Page 4 SSD7103 Linux Debian10.3.0 Installation Guide Disable "Secure Boot", set "Attempt Secure Boot" to "Disabled". 2. Set UEFI setting with ASUS PRIME X299 -DELUXE motherboard as an example: Set "Boot from Storage Devices" to "UEFI driver first"; And "Boot Device Control" to "UEFI Only" or "UEFI and Legacy OPROM";...
-
Page 5: Step 3 Flash Uefi Rom To Ssd7103
Set "OS Type" to "Other OS". Step 3 Flash UEFI Rom to SSD7103 Unzip SSD7103 UEFI package to root dir(/) of a USB flash driver,and insert the USB flash drive to the motherboard; Booting from the UEFI USB flash and enter the UEFI environment ;... -
Page 6: Step 4 Create Array
SSD7103 Linux Debian10.3.0 Installation Guide Step 4 Create Array Attach four NVMe SSD to SSD7103 Controller ; Note Make sure your USB flash partition format is NTFS or FAT32. Boot, in the presence of the motherboard Log screen, there will be NVMe SSD information：... -
Page 7: Step 5 Prepare The Driver Diskette
SSD7103 Linux Debian10.3.0 Installation Guide " " Command create RAID0 Create RAID0 array with all disks and with maximum capacity. ； " " Command exit For more command usages, refer to Appendix A. Step 5 Prepare the Driver Diskette Extract HighPoint_NVMe_Debian_10.3.0_x86_64_vx.x.x_xx_xx_xx.tar.gz to top(/) directory of an USB flash drive. - Page 8 SSD7103 Linux Debian10.3.0 Installation Guide d. When the Installation screen appears, press ‘e’ to edit boot command line option On the edit command window, move the cursor to the end of line “linux /install/vmlinuz... ”, and append "modprobe.blacklist=nvme" (double quotation mark are not include).
- Page 9 SSD7103 Linux Debian10.3.0 Installation Guide ← Unmount the USB flash drive # umount /hptdd When the USB flash drive is unmounted, please unplug the USB flash drive from the mainboard. And then execute following command to install driver to install the Linux Debian.
-
Page 10: Monitoring The Driver
This command will show the driver version number, physical device list and logical device list. 4 Installing RAID Management Software HighPoint RAID Management Software is used to configure and keep track of your hard disks and RAID arrays attached to controller. Installation of the management SSD7103 software is optional but recommended. - Page 11 SSD7103 Linux Debian10.3.0 Installation Guide Appendix A Support command: help/info/quit/exit/create/delete. Create Command Syntax Create Array Type (RAID0/RAID1/RAID10) Member Disk list (1/1,1/2|*)Capacity(100|*) Examples <<< create RAID0 <<< create RAID0 * <<< create RAID0 * * Create RAID0 array with all disks and with maximum capacity.
- Page 12 SSD7103 Linux Debian10.3.0 Installation Guide This is help message. - 10 -...
Need help?
Do you have a question about the SSD7103 and is the answer not in the manual?
Questions and answers