Quickie Easy 160i Directions For Use Manual page 6

Make sure that the attendant only holds the wheelchair using
securely mounted parts (e.g. not on the footrests or the
sideguards).
When using the lifting ramp make sure that the anti-tip tubes
fitted are positioned outside the danger area.
Secure your wheelchair on uneven ground or when transferring
(e. g. into a car) by using the brakes.
If and whenever possible, during a journey in a specially fitted
vehicle for disabled people, vehicle occupants should use the
seats in the vehicle and the appropriate restraint system. This is
the only way to ensure that occupants will have the maximum
protection if there is an accident. When using safety elements
offered by SUNRISE MEDICAL and using a specially designed
safety system, lightweight wheelchairs can be used as a seat
when being transported in a specially fitted vehicle. (See the
Chapter on "Transportation").
Depending on the diameter and setting of the castors, as well
as the centre of gravity setting of the wheelchair, the castors
may begin to wobble at high speeds. This can lead to the
castors being blocked and the wheelchair may tip over.
Therefore, please make sure that the castors are adjusted
correctly (see the Chapter "Castors"). In particular, do not travel
on an incline without brakes, travel at a reduced speed. We
recommend that novice users use anti-tip tubes.
Anti-tip tubes should prevent the chair tipping over backwards
unintentionally. Under no circumstances should they take the
place of transit wheels, and be used to transport a person in a
wheelchair with the rear wheels removed.
When reaching for objects (which are in front of, to the side or
behind the wheelchair) make sure that you do not lean too far
out of the wheelchair, as if you change the centre of gravity
there is a risk of tipping or rolling over. The hanging of
additional load (back pack or similar items) onto your chair
backposts can affect the rearward stability of your chair,
especially when used in combination with recliner backrests.
This can cause the chair to tip backwards causing injury.
For thigh amputees you must use anti-tip tubes.
Before setting off, check that your tyre pressure is correct. For
rear wheels it should be at least 3.5 bar (350 kPa). The max.
pressure is indicated on the tyre. The knee-lever brakes will
only work if there is sufficient tyre pressure and if the correct
setting has been made (see the Chapter on "Brakes").
If the seat and back sling are damaged, you must replace them
immediately.
Be careful with fire, in particular with burning cigarettes. Seat
and back slings can be set alight.
If the wheelchair is subject to direct sunlight for a long period of
time, then parts of the wheelchair (e.g. frame, legrests, brakes
and sideguard) may become hot (>41°C).
Always make sure that the quick-release axles on the rear
wheels are set properly and lock in. If the button on the quick-
release axle is not pressed in, the rear wheel cannot be
removed.
WARNING!
The effect of the knee-lever brake as well as the general driving
characteristics are dependant on tyre pressure. The wheelchair
is significantly lighter and easier to manoeuvre when the rear
wheels are pumped up correctly and both wheels have the
same pressure.
6
EASY 160i
WARNING!
Make sure that your tyres have sufficient tread! Please note that
you are subject to any and all traffic laws when driving in public
traffic.
WARNING!
Always be careful with your fingers when working or adjusting
the wheelchair!
The wheelchairs shown and described in this user guide may
not correspond in every detail exactly to your own model.
However, all instructions are completely relevant, regardless of
possible detail differences.
The manufacturer reserves the right to alter without notice any
weights, measurements or other technical data shown in this
manual. All figures, measurements and capacities shown in this
manual are approximate and do not constitute specifications.
We at SUNRISE MEDICAL have been awarded the ISO 13485
Certificate, which affirms the quality of our pro ducts at every
stage, from R & D to production. This product complies with the
standards set forth in EU directives. Optional equipment and
accessories are available at extra charge.