Advertisement
Quick Links
FEEDER CUBE
Plus
CE-48
ALL PURPOSE
OIL RESISTANT MODEL
IMPORTANT: APPLICATION NOTE
Replacement Parts:
Item
Designation Quantity
Control Card (quan. 1)
Fuse
(quan. 1)
Fuse Holder
(quan. 1)
Triac
(quan. 1)
S1
(quan. 1)
Switch Boot
(quan. 1)
Pot. Assembly (quan. 1)
Terminals
Knob
*Recommended spare parts to keep in stock.
RODIX INCORPORATED
rd
2316 23
Ave., ROCKFORD IL 61104
TOLL FREE (800) 562-1868, FAX (815) 316-4701
E-mail custserve@rodix.com
www.rodix.com
Characteristics Rodix P/N
240V
8 A, 250V
20 A, 250V
DPST
100K ohm
20A, 600V,2C Rodix No. 105-90
Rodix No. 123-294*
Rodix No. 106-20*
Rodix No. 106-17
Rodix No. 115-32*
Rodix No. 104-80*
Rodix No. 104-26
Rodix No. 123-229
Rodix No. 122-10
CE-48 Plus 24-211.doc 9/6/2012 Cover
Manufacturer P/N
Littelfuse 0214008
Littelfuse 03540901ZXGY
ST Micro. BTA40-600B-LF
Tyco 1520284-1
APM Hex. C1131/35-20
Altech CSCP2.5T
APEM 42011-3B-1/4
Advertisement
Related Manuals for Rodix FEEDER CUBE CE-40 Plus Series
Summary of Contents for Rodix FEEDER CUBE CE-40 Plus Series
- Page 1 Rodix No. 104-26 APM Hex. C1131/35-20 Pot. Assembly (quan. 1) 100K ohm Rodix No. 123-229 Terminals 20A, 600V,2C Rodix No. 105-90 Altech CSCP2.5T Knob Rodix No. 122-10 APEM 42011-3B-1/4 *Recommended spare parts to keep in stock. CE-48 Plus 24-211.doc 9/6/2012 Cover...
- Page 2 The can be smoothly adjusted from zero to maximum Rodix control operates on 50 or 60 Hz. by the main control knob. If part sensors are used, the control starts and stops automatically...
-
Page 3: Adjustments & Set Up
speed of the vibratory feeder. When very precise C. Low Voltage DC can be used to turn the ADJUSTMENTS & SET UP adjustment of the MAIN CONTROL DIAL is needed, control ON and OFF. Move jumper "J1" from increase the MIN trimpot setting and/or decrease the terminal 7, to terminal 5, (6 remains the MAX trimpot setting. -
Page 4: Warranty
Disable LVC Rodix Inc., ATTN: Repair Department 2-Speed Operation If under warranty, Rodix will repair or replace your control at 30/40 Pulse Operation no charge; If out of warranty, we will repair it and you will be Low Amplitude at “1”... -
Page 5: Line Filter
The plug and socket must have a breaking capacity of at least the amperage of the vibratory feeder(s). 4/27/12 2000, 2012 RODIX INC The size of the Mains supply wires should be 1.5mm² (#16 AWG) or larger. - Page 6 Rodix controls have been designed with a AUX output. The shield “drain” wire high degree of immunity to electrical RECTIFIER should be tied to the chassis in the Rodix noise; however, depending on the control RELAY DIODE control. The drain wire should be kept...
- Page 7 Machine Safety Report Number – 98021628.J02 Machine Safety testing performed by: Intertek Testing Services, 7435 4th Street North, Oakdale, MN 55128 EMC testing was performed by Rodix at: L.F. Research, 12790 Route 76, Poplar Grove, IL 61065 Machine Description: Vibratory Feeder Control...
- Page 8 R.C. or D.C. A.C. Rectified Full Wave AC Direct Current Alternating Current Half Wave Full Wave 3600 Vibrations Per Min. 7200 Vibrations Per Min. From TUV Rheinland, FAQ http://www.jpn.tuv.com/en/services/product_testing/all_types_of_products/electromagnetic_compatibility_services_emc_/emc_faq.php © RODIX Inc. 2006 E:\Eng\CE\CE restrictions for harmonic current emissions 060501.doc...
- Page 9 The amount of voltage fluctuations and flicker depends on how often the electrical load is turned On and Off by the machine and how large the load is. From TUV Rheinland, FAQ http://www.jpn.tuv.com/en/services/product_testing/all_types_of_products/electromagnetic_compatibility_services_emc_/emc_faq.php © RODIX Inc. 2006 E:\Eng\CE\CE Flicker 060511.doc...
- Page 10 195 On/Off cycles per 1 minute Unlimited On/Off cycles per 1 minute This chart is based on Rectangular voltage changes at equal intervals using the Pst=1 chart, fig. 4 of standard EN61000-3-3. Plt = Pst x 0.65 © RODIX Inc. 2006 E:\Eng\CE\CE Flicker 060511.doc...
Need help?
Do you have a question about the FEEDER CUBE CE-40 Plus Series and is the answer not in the manual?
Questions and answers