Page 3
If you control the products with a software from CETONI GmbH, you agree to the applicable license agreement, which can be read in the corresponding software manual. This and all other current product manuals can be found at https://www.cetoni.com/service/manuals.
Overviews and Indexes 1.1 Content Overviews and Indexes Content Change History Introduction Foreword Symbols and Key Words Used Norms and directives General Description of the Device Intended Use Reasonably Foreseeable Faulty Application Safety Advice Scope of Supply Base Module Base 120 Hardware Operation Technical Data 4.2.1...
Page 6
5.2.3 Interfaces 5.2.4 Environment Extension Base Module Base 600XT Hardware Operation Technical Data 6.2.1 Mechanical Data 6.2.2 Electrical Data 6.2.3 Ambient Conditions In-Line System Extension Off-Line Power Supply Transportation and Storage Maintenance and Care Disposal Base Module Hardware Manual...
1.2 Change History DATE CHANGE VALID FOR 2.00 08.04.2015 Thematic splitting of the manual “Qmix date of purchase after 08.04.2015 hardware” 2.01 11.03.2016 New corporate design date of purchase after 08.04.2015 2.03 24.05.2017 New image material for new design of Base date of purchase after 08.04.2015 120 and Base 600 2.04...
Introduction 2.1 Foreword Thank you for purchasing a product from CETONI. With this user manual we would like to support you as well as possible when handling the device. If you have any questions or suggestions, please do not hesitate to contact us.
2.4 General Description of the Device The base modules Base 120, Base 600 und Base 600XT are used to supply a CETONI system with a supply voltage of 24V. Base 120 and Base 600 also provide a USB interface for connection to a PC.
2.7 Safety Advice For the safe operation of a base module, it is essential to observe the safety measures in the CETONI System manual. IMPORTANT. Please read this manual as well as the related software manual carefully and completely before putting your Qmix system into operation.
Scope of Supply The delivery of the Base 120 and Base 600 should include the following items in addition to the unit itself (does not apply to BASE 600 XT): COUNTRY SPECIFIC POWER CABLE FOR NON- HEATING APPARATUS USB CABLE INTERCONNECT CABLE 0,5m BUS TERMINATING PLUG Base Module Hardware Manual...
Page 12
HARDWARE-MANUAL AND CD WITH SOFTWARE- MANUAL, SOFTWARE AND DRIVERS Base Module Hardware Manual...
Base Module Base 120 4.1 Hardware Operation Type Plate USB-socket (type B) Fuse Power Switch Power Socket The base module supplies all other modules with power and serves as an interface to your PC. The Base 120 base module can continuously supply a power of 120 W. In the section technical data →...
4.2 Technical Data 4.2.1 Mechanical Data DIMENSION (L X B X H) 310 x 100 x 56 mm WEIGHT ≈1800 g 4.2.2 Electrical Data SUPPLY VOLTAGE 90 ~ 260VAC FREQUENCY 47 ~ 63 Hz POWER OUTPUT 24VDC; 5A; 120 W 4.2.3 Interfaces 1.1 und 2.0...
Base Module Base 600 5.1 Hardware Operation Ventilation Grille Type Plate USB-Port Type B Fuse Mains switch Mains Connection The Base Module supplies all connected modules with electricity and serves as an interface to your PC. The Qmix Base Module can provide a maximum power output of 650W permanently. For any module connect, power consumption...
Page 16
The mains switch is located to the right of the mains connection. It will light up red when the device is connected and switched on. The USB-port (type B) is used to connect the Qmix system with your PC. Pay attention not to cover the ventilation grilles. Otherwise the device might switch off to avoid damage due to overheating.
5.2 Technical Data 5.2.1 Mechanical Data DIMENSION (L X B X H) 310 x 200 x 56 mm WEIGHT ≈3700 g 5.2.2 Electrical Data SUPPLY VOLTAGE 90 ~ 260VAC FREQUENCY 47 ~ 63 Hz POWER OUTPUT 24VDC; 27A; 650 W 5.2.3 Interfaces 1.1 und 2.0...
Extension Base Module Base 600XT 6.1 Hardware Operation The Extension Base Module is used if the power of the normal Base Module is not sufficient to feed your entire system with energy. It also provides a maximum power of 650 W. For any module you connect, the power consumption value can be found in the section Technical Data of the appropriate manual.
The Extension Base Module can only be operated in connection with an existing system. It automatically turns on and off with this. The connections of the Extension Base Module are explained below: DESCRIPTION Mains connection with fuse (Ø5x20mm see type plate) Connector for connection to the base system via Interconnect cable Display for the current power output (650W max.) Three connectors for off-line loads (450W max.
6.2.2 Electrical Data SUPPLY VOLTAGE 264VAC FREQUENCY 63 Hz POWER OUTPUT 24VDC; 27A; 650 W 6.2.3 Ambient Conditions OPERATING TEMPERATURE 0°C to 50°C STORAGE TEMPERATURE -20°C to 75°C OPERATING / STORAGE AIT HUMIDITY 20% to 90%, non-condensing The extension base module can be used in two different ways, which are explained below: 6.3 In-Line System Extension In the case of in-line system extension, the Extension Base Module is connected to an existing base system via an interconnect cable.
Page 21
System Extension Interconnect cable Base System Simply connect the last module of your base system to the corresponding connector of the Extension Base Module via the interconnect cable. Furthermore connect it to the mains supply. Interconnect Cable Power Supply Cable Base Module Hardware Manual...
6.4 Off-Line Power Supply When used Off-Line, at most three devices can be supplied with power by the Extension Base Module. Only devices with potentially high power consumption, which are equipped with the appropriate connector, can be connected Off-Line. All other devices of the base system are still supplied with power by the Base-Module of the base system.
Page 23
Mains Connection Plug and tighten Base Module Hardware Manual...
Transportation and Storage Please do not lift and transport the modules in the plugged-together state. Transport in the plugged- together state only permitted in the original packaging. Use the original packaging for transport and shipping of the modules. Observe the specifications in chapter "Technical data" for storage. CAUTION.
CETONI GmbH to coordinate further actions. The device may only be opened by CETONI GmbH or thereby authorized service staff. Otherwise the warranty and guarantee claims are void.
Disposal Please send your old devices back to CETONI GmbH. We will take care of proper disposal. If necessary, please decontaminate the device before sending it back and attach a completed decontamination declaration with your shipment. Base Module Hardware Manual...