Advertisement
Edit IP
Mac Address
Address
.
.
192 168
1 . 45
Subnet Mask
255 255 255 . 0
.
.
.
.
Gateway
192 168
1 . 1
Username
admin
Password
OK
⑤
Checkmark the device you want to add and then click "Add" button.The
NVR will automatically refresh the cameras and return to "Edit Camera"
interface. "Online" status means connecting the device successfully and
you will see the live image. You may select the added device and click
button to modify channel, IP address, etc.
Edit Camera
Edit Camera Group
IP Planning
No.
Camera Name
Address
Port
Status
Protocol
Model
1
IP Camera 1
192.168.1.20
80
Online
Nuvico Xcel
NCT-5ML-B2
2
Nuvico Xcel
NCT-5ML-B2
IP Camera 2
192.168.1.38
80
Offline
Nuvico Xcel
NCT-5ML-B2
3
IP Camera 3
192.168.1.45
80
Online
Remain Bandwidth: 85/120Mb
Edit Camera
Camera Name
IP Camera 1
Address
192 168
.
.
1 . 58
Port
9008
Nuvico Xcel
Protocol
NCT-5ML-E2
Model
Username
admin
Password
Test
OK
►WAN
① Set the network of the NVR. Go to Start → Settings → Network → PPPoE.
Enable PPPoE and then enter the user name and password received from your
ISP.
② Go to Start → Settings → Camera. Click "Add Camera" or
column of the search camera and select "Manually Add" to add the IP cameras.
Enter IP address, server port, username and password of the IP camera. The IP
camera must be connected over WAN. And here the IP address of the IP camera
must be a WAN IP address.
8. UPnP
You can use the UPnP function to enable the fast connection of the device to
WAN via a router without port mapping.
① Go to Start → Settings → Network → UPnP, and enable UPnP and then
click "Apply" button to save.
② Enable the UPnP function in the router.
③ Click "Refresh" button to refresh the UPnP status. If the UPnP status were
still "Invalid UPnP" after refreshing it for several times, the port would be wrong.
Please change the mapping type to "Manual" and then click
Sync to IPC
port until the UPnP status turns to "valid UPnP".
Cancel
9. NAT
►NAT Settings
Search Camera
① The NVR shall be powered on and connected to the network.
Preview
Edit
Upgrade
Version
② Go to Start → Settings → Network → TCP/IP. You can obtain the IP address,
4.1.0.0
4.1.0.0
subnet mask and gateway automatically. You can also manually enter them
4.1.0.0
according to the actual network situation. Please make sure the network segment
is the same as that of the network which is used.
③ Set the preferred or alternative DNS Server. Click "Apply" to save the
parameters.
④ Go to Start → Settings → Network → NAT tab. Enable NAT and select the
Sync to IPC
NAT Server Address (The default NAT Server Address is nat.autonat.com).
Click "Apply" to save the parameters.
Cancel
►
NAT Access
After finishing the NAT settings, you can enter www.autonat.com in the
behind the
address bar of your browser and then press enter to go to the following
interface. If you are the first time to access the NAT, you shall download and
install the ActiveX according to the popup tips. After installing ActiveX
successfully, it will pop the login box.
UPnP
Enable
Map Type
Auto
Port
Port Type
External Port
External Address
UPnP Status
Edit
HTTP Port
80
183.17.254.19
80
Valid UPnP
183.17.254.19
443
Valid UPnP
HTTPS Port
443
Valid UPnP
Server Port
6036
183.17.254.19
6036
554
Invalid UPnP
RTSP Port
554
Refresh
Apply
NAT
Visit Address
www.autonat.com
Enable
NAT Server Address
nat.autonat.com
Apply
Enter device serial number
Enter Username
Enter Password
Login
Device Serial Number
: Click
interface to check the serial number or go to Start
Network Status to check the serial number of the NVR).
to modify the
Username: The username of the NVR. The default username is admin.
Password: The password of the NVR. The password is set by yourself when
you configure the wizard for the first time.
10. Manual Recording
Before recording, please install and format a HDD. In the live interface
you can see the menu toolbar. Click
it again to stop recording. You can also click
the recording.
11. Playback
►
Instant playback
Click "Instant Playback" in the right-click menu of the camera's preview
window to select or drag the playback progress bar to change the playback
time to play back the record.
►General playback
Click
on the tool bar at the bottom of the live preview interface or click
Start → Playback to go to the playback interface as shown below. You can also
add the playback cameras manually. Click
up the "Add Camera" window. Check the cameras in the window and then click
"Add" to add playback camera. The record files of the added playback camera
will be played in the playback interface.
on the menu bar at the bottom of the live
→
→
→
Settings
Network
button to start recording. Click
to check the status of
in the playback window to pop
TN-P1600AI-8P450041001209 A0
Advertisement
