1. Manuals
  2. Brands
  3. JBO Manuals
  4. Test Equipment
  5. eMultiCheck
  6. Instruction manual

JBO eMultiCheck Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
eMultiCheck-Instruction manual

Advertisement

Table of Contents
loading

Related Manuals for JBO eMultiCheck

Summary of Contents for JBO eMultiCheck

  • Page 1 manual...

  • Page 2: Table Of Contents

    INTRODUCTION ......................2 Starting up ................................3 Switching on ................................4 Switching off ................................4 Procedure of inspection for internal threads with gauges ..............4 USING THE EMULTICHECK ................... 5 Screwing in: ................................5 2.1.1 Manual mode ..................................5 2.1.2 Through-holes ...................................

  • Page 3: Introduction

    SAFETY INSTRUCTIONS ..................... 13 1 Introduction The eMultiCheck is the latest development by JBO. The "e" stands for a combination of our well- proven MultiCheck with a motorised drive which is controlled by a microprocessor. Scope of delivery: 2. 2. Gauge sleeve 4.

  • Page 4: Starting Up

    Before the device is used for the first time, it should be fully charged in order to ensure a maximum battery life. To do this, just push the eMultiCheck into the charging station. An indexing system on both parts ensures that it can only be pushed in the right way round. The first time, the charging time should be at least one hour.

  • Page 5: Switching On

    Button C Button B Button A Fig 4: eMultiCheck 1.3 Switching off The device switches off automatically after about 3 minutes when none of the buttons are pressed. 1.4 Procedure of inspection for internal threads with gauges Application of the GO screw plug gauge The GO thread plug gauge checks the virtual size of the internal thread.

  • Page 6: Using The Emulticheck

    2 Using the eMultiCheck The eMultiCheck is operated with the two buttons on the front of the device. The blue button (button C) at the side is used for adjustment. 2.1 Screwing in: To begin the measuring process, press the black button (button B) on the front and the plug gauge begins to turn slowly (phase 1).

  • Page 7: Display

    3 Display Cover for RS 232-interface Battery cover (Cr2032) (MODE) button (SET) button Electronics data: Range Power supply 1 Lithium Batterie 3V, Typ CR2032 Resolution 0,01 mm Consumption 40yA Accuracy 40ym Battery life 5000 Stunden Repeatability 10ym Data output RS232-kompatibles Format Max.

  • Page 8: Preset Mode

    3.3 Preset mode Preselection of a reference value (preset) The two reference values (REF I and REF II) can be preselected differently and up to a maximum preset value of ± 2999.99 mm / ± 89.9995 IN. 1. Select active reference value (in reference mode). 2.

  • Page 9: Setting

    4 Setting Before changing to Setting mode you must change to the M8 thread plug gauge which is delivered as standard (except for changing the depth mode). A gauge sleeve is not needed in this case! Press and hold the blue button at the side (button C) for a while (approx. 3 seconds) to change to Setting mode.

  • Page 10: Pattern Of Movement

    4.1.1 Pattern of movement Different patterns of movement can occur during the setting process. These are characterised by: (left-hand rotation) 1. One short turn 1st hole is the next hole 2. Two short turns 2nd hole is the next hole 3.

  • Page 11: Setting Level 2, Depth Measurement

    4.2 Setting level 2, Depth measurement In the depth measurement, the aim is to move gently towards the end of the thread, as previously described above. This is done by counting and saving the number of revolutions required for the previous measurement.

  • Page 12: Screwing In The Gauge Sleeve

    For thread sizes of more than M14, the gauge sleeve must be screwed in first and then the plug gauge. The sleeve can be pulled back at the opening in the gauge sleeve. The eMultiCheck is now ready for use. Fig 8: eMultiCheck ready for use...

  • Page 13: Charger

    Short-circuit protection 7 Option – operation with wall power supply Here, the power supply for the eMultiCheck is supplied from a standard household mains socket (100 – 240 V/AC, 50/60 Hz). The wall power supply has short-circuit and overload protection.
  • Page 14 Protect the product from extreme temperatures, direct sunlight, strong impacts, high humidity, wetness, flammable gases, vapours and solvents. Never immerse the eMultiCheck in water, salt water, drinks or other liquids. Do not subject the product to mechanical stress. If safe operation is not possible, put the device out of service and take measures to ensure that it is not used inadvertently.
  • Page 15 Other Please consult an expert if you are in any doubt about product functions, safety or electrical connection. Always have maintenance, alteration and repair work carried out by a specialist or a specialist dealer. The product is manufactured in accordance with the ROHS Directive (Restriction of Hazardous Substances) and can therefore be disposed of in accordance with the WEEE Directive.

Table of Contents