1. Manuals
  2. Brands
  3. RGBlink Manuals
  4. Computer Hardware
  5. FLEX 16
  6. Quick start manual

RGBlink FLEX 16 Quick Start Manual

Hide thumbs Also See for FLEX 16:
Table of Contents

Advertisement

Quick Links

Download this manual
FLEX 16
Quick Start
● Fully Modular 16 ×16 signal architecture
● Mixed signal matrix switching
● Up to 33 mega pixels output splicing
● Load and save up to 256 presets
● Output resolution up to 2048x1152@60Hz /
2560x816@60Hz
● EDID management
● Remote control by XPOSE and RGBlink OpenAPI

Advertisement

Table of Contents
loading

Related Manuals for RGBlink FLEX 16

Summary of Contents for RGBlink FLEX 16

  • Page 1 ● Mixed signal matrix switching ● Up to 33 mega pixels output splicing ● Load and save up to 256 presets ● Output resolution up to 2048x1152@60Hz / 2560x816@60Hz ● EDID management ● Remote control by XPOSE and RGBlink OpenAPI...

  • Page 2: Table Of Contents

    CONTENTS Product Introduction.............................. 3 Packing Configuration............................4 Hardware Orientation............................5 Front Panel...............................5 Rear Panel................................ 7 Software Operation..............................8 Software Installation............................. 8 Software Operation............................11 Login to the Software...........................11 Connect Setting............................. 13 Output Setting............................15 Operation Mode.............................19 System Setting............................31 Access control............................33 Logout..............................35 Contact Information.............................

  • Page 3: Product Introduction

    Product Introduction FLEX 16 is a matrix capable to distribute any input signal to any output signal through its consistent modular capability to control up to 16 different inputs and 16 different outputs independently. Different devices can be connected in each output and input. It supports HDMI, DVI, SDI, USB and HDBaseT input and output signals, as well as DP output.

  • Page 4: Packing Configuration

    Packing Configuration AC Power Cable Ethernet Cable Converter DVI-VGA Converter DVI-RCA USB Disk HDMI To DVI Antistatic Bag Cable Note: AC Power Cable supplied as standard according to destination market Upgrade tool package and user manual are stored in the USB disk, please keep it. 4/30...

  • Page 5: Hardware Orientation

    Hardware Orientation Front Panel Standard Front Panel Panel Instruction LAN indicator indicating communication through LAN USB interface for upgrading port ， lights up when LAN port is connected, flashes when LAN communication happens IR indicator Power indicator Indicate IR communication flashes lights when device has power supply.
  • Page 6 Matrix Panel for option Panel Instruction IN 1~16， Input signal source selection USB interface, for upgrading button LCD Panel OUT 1~1，Output port selection Show operation menu items button Power indicator Menu button to open up menu items lights when device has power supply. and back Serial Port indicator lights up when serial port is connected,...

  • Page 7: Rear Panel

    Rear Panel Input Interface Input Module Slots Supports input signals including HDMI, DVI, SDI, USB and HDBaseT. Output Interface Output Module Slots Supports input signals including HDMI, DVI, SDI, USB, HDBaseT and DP. Control Interface LAN Port and Serial Port Power Connection Power Supply Module, IEC-3 7/30...

  • Page 8: Software Operation

    Software Operation Software Installation Minimum Requirements Windows Operation System Windows 7/8/10 Processor 1GHz/32 bit or 64 bit processor Memory Hard Disk 16Gb Graphics 128Mb/DirectX9 Display 1280X720 Operation System Mac OS Processor 1.0GHz+ Memory 512M+ Hard Disk 512M+ Graphics 512M+ Display 1366x768 8/30...
  • Page 9 1. Double click icon , it will pop-up the Installer Language box, select the language, for example, select “English”, and click “OK” to confirm. It will pop-up the installer box, and click “Next” to install, as follows: 2. Select “Browse...” to select the XPOSE software install location and click install: 9/30...
  • Page 10 User should get the rights in “Roles Management” when install the software to disk C if the system is Windows 7 or above. 3. Click “Finish” and is ready to run the XPOSE management software: 10/30...

  • Page 11: Software Operation

    The user name is Admin, and default there is no password. Select “FLEX 16”, select language “English” and enter the software by clicking “Login”. 2. If user wants to change the language to Chinese, click the drop down arrow after “Language” and select “Chinese”, then click “Login”...
  • Page 12 XPOSE management software consists of Output Setting, Operation Mode, System Settings, Access Control and Log out. In the following parts come with the details. 12/30...

  • Page 13: Connect Setting

    Connect Setting The remote controller PC which runs XPOSE connects with Flex 16 by the network cable or USB-RJ11 serial cable (with the standard accessories). After login on XPOSE, Search device and find FLEX 16 Click the FLEX 16 icon and sync...
  • Page 14 And sync done. 14/30...

  • Page 15: Output Setting

    Output Setting Output setting 28 types of standard resolution available to choose. 15/30...
  • Page 16 User can custom the resolution if no proper resolution in the list, Note:avoid using following resolution 720x480i@60Hz and 720x576i@50Hz (not supported on all output modules), 2560*816@60and 2048*1152@60 (not supported on DVI and HDMI output) . 16/30...
  • Page 17 Output setting is for all output ports from one output EXT (EXT-4 or EXT-6) DE setting Board type:EXT-6 (EXT 4F-OS Splicing EXT interface) EXT 4 (EXT 4F OM Matrix EXT interface, EXT 4F IM matrix input ext interface) Port :1-16 Output Type:DVI or HDMI Color Range:Image or Video Bits:DVI 8bits, HDMI 8bits|10bit|12bit...
  • Page 18 DE setting done 18/30...

  • Page 19: Operation Mode

    Operation Mode There are 2 working modes, including the Matrix mode and Splitting Mode. Click the “Operation Mode”, and enter the interface as follows: Matrix Mode and Splitting Mode are included in operation mode, specific as follows: 1. Matrix Mode Click the “Matrix Mode”, and enter to the interface as follows: In matrix mode, is available signal selection, bank selection, transition time and black out setting.
  • Page 20 Default source 1 to monitor 1, source 2 to monitor 2, and so on. Select the signal, and drag it to the source that will set. For example, set signal 3 for source 13, as shown in the figure below: Source 13 will be switched to signal 3, click source 1, then click “TAKE”...
  • Page 21 Signal List The signal list is shown as follows: It displays the input module type, the quantity of inputs and input format. Right click the input for the following settings: Change Name: Select “New Name”, and input the new name, click “OK” after setting. Refresh Signals: Right click the input and select “Refresh Signals”.
  • Page 22 USB movie player setting: Can select play in order, random, single cycle and all cycle, switch to pre or next, pause or play, and read the movie name, progress bar and time. USB picture play time: Click the picture, it will display the setting interface, default the time is 0s. Set the switch time, and click “Set”.
  • Page 23 Scale: Set the X, Y, width and height. Crop: Crop the left, top, width and height. Display Mode: Select “Live” or “Freeze”. Mirror: Enable or disable the mirror function, default “OFF”. Bypass Mode: Enable or disable the bypass mode. When select “ON”, the output format will be the same with the input format.
  • Page 24 Output Setting Click on shortcut , it will enter the interface as follows: Close monitor: Click the icon on the top right corner of the monitor to close one monitor, or click the shortcut on the right side of the interface to close all monitors. Reset outputs: User can reset outputs by clicking the shortcut on the right side of the interface.
  • Page 25 Auto tile: User can enable or disable the auto tile function by clicking the auto tile shortcut on the right side of the interface. If select auto tile “ON’, the layer will automatically snap to the output grid when move the layer to the position within the threshold value.
  • Page 26 Layer Setting New Layer: In input screen zone of controlling software, press the left mouse key and drag on the intended output screen to cover the whole current screen. And the below interface will be displayed. A layer can also be opened by double right clicking the left signal source to be shown on the window.
  • Page 27 or layer backward “ ”. The layer can be set as background by click “ ” and click “ ” to close layer background. Close one layer or all layers: Click the icon on the top right corner of the layer to close one layer, or click the shortcut key “...
  • Page 28 Color Term: Set the color temp (red, green and blue), the adjustment range is 0~100. Reset: Select “Reset”, the input property will be recover to factory setting. Take The take interface is shown as the figure below: Set the transition time, and the adjustment range is 0~10S. Slide the black out switch to enable or disable the black function.
  • Page 29 Loop Click the loop shortcut “ ”, and pop-up window as follows: Slide the loop switch to enable or disable the loop function for the bank. If select “ON”, the bank play time can be set. Sync Click the sync shortcut “ ”...
  • Page 30 Factory Reset Click the factory reset shortcut “ ” to reset to factory settings. Page Set Click the page set shortcut “ ” to load and save pages. Shortcut Keys Click the shortcut “ ”, and pop-up window as follows: Use shortcut key to operate fast and easily.

  • Page 31: System Setting

    System Setting Click “System Settings” in the main interface: 1. Connect Setting Click “Connect Setting”: Select ”COM Port” and “Baud Rate”, click the drop down arrow after them, and click “OK”. Setting the device connecting ways: Serial Connect, Ethernet Connect and Search by this configuration. After setting ”COM Port”...
  • Page 32 2. IP Settings Click the “IP Settings”, and pop-up window as follows: Default “Auto get IP address”. Users can also set IP address, Mask and GateWay manually. This is usually used if one computer control some devices or remote control. It takes effect after reboot the software if change IP through network.

  • Page 33: Access Control

    Display the device version information. Including Model Number, Serial Number, IP Address, firmware version, etc. 4. Factory Reset Click “Factory Reset”, and pop-up window as follows: Click “OK” or “Cancel” to confirm the reset. Access control Click “Access control” in the main interface: Role management and rights management are included in access control, specific as follows: 33/30...
  • Page 34 1. Access Control Click “Access Control” and pop-up window as follows: Add: Input the user name and password, and select the user type as “Admin’ or “Users”, click “Add” after setting. Edit: Select the admin or users in user’s list, then edit the password or user type, click “Edit” after setting. Del: Select the admin or users in user’s list, then click “Del”, the selected user will be deleted.

  • Page 35: Logout

    Logout Click “Logout” to exit the XPOSE sorftware, and pop up window as follows: Click “cancel” or “OK” to confirm User also can be click the right corner red button to exit software directly. 35/30...

  • Page 36: Contact Information

    All video products are designed and tested to the highest quality standard and backed by full 3 years parts and labor warranty. Warranties are effective upon delivery date to customer and are non-transferable. RGBlink warranties are only valid to the original purchase/owner. Warranty related repairs include parts and labor, but do not include faults resulting from user negligence, special modification, lighting strikes, abuse(drop/crush), and/or other unusual damages.

Table of Contents