Maintenance; Protecting The Environment - Black & Decker GL7033 Manual

ENGLISH
Automatic line feed does not work
Keep the tabs depressed and remove the spool cover
u
from the housing.
Pull the cutting line until it protrudes 11 cm from the hous-
u
ing. If insufficient cutting line is left on the spool, install a
new spool of cutting line as instructed above.
Align the tabs on the spool cover with the cut outs in the
u
housing.
Push the cover onto the housing until it snaps securely
u
into place.
If the cutting line protrudes beyond the trimming blade, cut
u
it off so that it just reaches the blade.
If the automatic line feed still does not work or the
spool is jammed, try the following suggestions:
Carefully clean the spool cover and housing.
u
Remove the spool and check if the lever can move freely.
u
Remove the spool and unwind the cutting line, then wind it
u
on neatly again as described above. Replace the spool as
instructed.

Maintenance

Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory opera-
tion depends upon proper tool/appliance care and regular
cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
u
tool if the appliance/tool has a separate battery pack.
Or run the battery down completely if it is integral and then
u
switch off.
Unplug the charger before cleaning it. Your charger does
u
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your tool/appliance
u
and charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
Regularly clean the cutting line and spool using a soft
u
brush or dry cloth.
Regularly use a blunt scraper to remove grass and dirt
u
from the underneath of the guard.

Protecting the environment

Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
10
(Original instructions)
Technical data
GL7033
Type 1
Voltage V 230
AC
Power Input W 700
No-Load Speed min 7000
-1
Weight kg 3.2
Level of sound pressure:
Sound pressure (L ) 81 dB(A), uncertainty (K) 1.2 dB(A)
pA
Sound power (L ) 95 dB(A), uncertainty (K) 1.2 dB(A)
WA
Vibration total values (triax vector sum) according to EN 50636-2-91:
Vibration emission value (a ) 8.2 m/s , uncertainty (K) 1.5 m/s
2
h
EC declaration of conformity
MACHINERY DIRECTIVE
%
OUTDOOR NOISE DIRECTIVE
GL7033/GL8033/GL9035 - Trimmer
Black & Decker declares that these products described under
"technical data" are in compliance with:
2006/42/EC, EN60335-1:2012 + A11:2014 + A13:2017 +
A1:2019 + A14:2019 + A2:2019, EN50636-2-91:2014,.
2000/14/EC, Lawn Mower, L < 50cm, Annex VI,
DEKRA Testing and Certification GmbH,
Handwerkstraße 15, 70565 Stuttgart
Location Certification Body,
Dinnendahlstr. 9, 44809 Bochum Germany
Notified Body number: 0158
L (measured sound power level) 95 dB(A),
WA
Uncertainty (K) = 1,2 dB(A),
L (guaranteed sound power) 96 dB(A).
WA
These products also comply with directive
2014/30/EU and 2011/65/EU.
For more information, please contact Black & Decker at the
following address or refer to the back of the manual.
GL8033 GL9035
Type 1 Type 1
230 230
800 900
7000 7000
3.2 3.2
2