Download Print this page

Furniture Solutions VEGA 18VEGBSX2.AB Manual

Barstool

Advertisement

Quick Links

Made in China
Imported by Furniture Solutions (Aust) Pty Ltd
10-16 Daisy St, Revesby, NSW. 2212
Your furniture purchase is an investment.
Here are a few tips to maximize the lifetime of your furniture with a minimum,
amount of effort.
Properly caring for your furniture can help ensure that it looks great year after year.
Wood Furniture Maintenance:
Note no added polishing is required.
Always dust, wipe, and clean with the grain of the wood.
Dust with a soft clean cloth.
Dust will scratch the furniture surface if not removed properly!
If a polished surface becomes foggy.
Rub it with a cloth dipped in a solution of one tablespoon
vinegar to one liter of water. Rub softly with the grain until the
surface is completely dry.
Soap and water are not advisable for wood surface.
Water can penetrate the finish and raise the grain on wood,
causing damage.
Remember to change dusting cloths frequently as dirty cloths
may scratch your furniture's surface.
Iron Work Maintenance:
Keep dust free; Bolts and screws must be checked and
re-tightened as necessary or minimum very 6 months.
Paint chips should be touched up as they occur. When bare
metal is exposed to environment, metal will first oxidize and next
stage will be rust, causing structural integrity to be
compromised.
VEGA BARSTOOL
Item# 18VEGBSX2.AB
Height: 762mm
Seat: 406mm Round
Stain: Aged Barley
The Enemies of Wood:
Moisture is wood's worst enemy.
Liquid spills should be gently wipe up immediately.
Coasters should be used under all beverages.
Do not allow rubber or vinyl materials to lie on the furniture.
Chemicals in rubber may leave a stain.
Put a strip of felt or leather under accessories that have
rubber or vinyl.
Heat creates a chemical change in the furniture's finish,
which result in a white spot. Use protective pads under hot
dishes, appliances, etc.
Sunlight's ultraviolet rays can damage the finish of
furniture.
Do not place furniture directly against a heater or radiator
and do not place in the path of hot streams of air from
central heating. This will cause extreme localized drying of
the wood.
The Enemies Iron Work:
All iron or steel products are painted to protect metal from
the elements.
Do not immerse in water. Liquid spills should cleaned off
immediately. Alcohol, fruit juice etc are acidic and can
cause paint finish to change colour. When cleaning please
use only Ph neutral products.
Page 1 of 6

Advertisement

loading
Need help?

Need help?

Do you have a question about the VEGA 18VEGBSX2.AB and is the answer not in the manual?

Questions and answers

Summary of Contents for Furniture Solutions VEGA 18VEGBSX2.AB

  • Page 1 Page 1 of 6 VEGA BARSTOOL Made in China Item# 18VEGBSX2.AB Imported by Furniture Solutions (Aust) Pty Ltd Height: 762mm 10-16 Daisy St, Revesby, NSW. 2212 Seat: 406mm Round Stain: Aged Barley Your furniture purchase is an investment. Here are a few tips to maximize the lifetime of your furniture with a minimum, amount of effort.
  • Page 2: Pre-Assembly Preparation

    Do not over tighten the screws and bolts as this may damage the threads MINUTES ALLOW TIME PEOPLE REQUIRED For any assistance with assembly or for missing parts Please contact: Place of purchase or Furniture Solutions. Customer Service (Australia) Phone-1300 794 188 Email- customerservice@furnituresolutions.com.au...
  • Page 3 Page 3 of 6 Vega Barstool Hardware and Component List Hardware List:Item #PVG420BS-AH Spring Washer 12PCS Flat Washer 12PCS 6mm x 13mm Bolt 12PCS 6mm x 16mm Tool 4mm Componet List Please note factory have pre-assembled seat frame, swivel plate and seat bottom frame. Factory has also pre-fitted the plastic plug in base of leg.
  • Page 4 Page 4 of 6 Assembly Instructions Prepare as instructed on page 2: Follow steps do not move ahead Step 1: Fit 3 legs to base of seat as shown below, note leg has a threaded hole inside of tube, this faces into the middle of stool seat.
  • Page 5 Page 5 of 6 Assembly Instructions Step 3: Fit last Leg as indicated in diagram. Please follow same method as previously shown. remember to only do bolts up finger tight. Once you have fitted by hand all bolts, you need to B A C ensure that the stool when finished is square/level.
  • Page 6 To make a warranty claim, customers can either contact the retailer where the purchase was made or Furniture Solutions on contact details below. Proof of purchase will be required before proceeding with any claim. In the case of product defects providing photos may be able to speed up processing of the claim.