Page 1 PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936 PIONEER CORPORATION 2002 T –...
Page 2 PDP-433CMX, PDP-433MXE SAFETY INFORMATION This service manual is intended for qualified service technicians ; it is not meant for the casual do-it- yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual.
Page 3 PDP-433CMX, PDP-433MXE PRODUCT SAFETY NOTICE Many electrical and mechanical parts in PIONEER set have special Leakage Current Cold Check safety related characteristics. These are often not evident from With the AC plug removed from an AC power source, place a visual inspection nor the protection afforded by them necessarily jumper across the two plug prongs.
Page 4 PDP-433CMX, PDP-433MXE CHARGED SECTION AND HIGH VOLTAGE GENERATING POINT 7 Charged Section 7 High Voltage Generating Point The places where the commercial AC power is used without The places where voltage is 100V or more except for the charged passing through the power supply transformer.
Page 5 PDP-433CMX, PDP-433MXE [ Important symbols for good services ] In this manual, the symbols shown-below indicate that adjustments, settings or cleaning should be made securely. When you find the procedures bearing any of the symbols, be sure to fulfill them: 1.
Page 6: Table Of Contents
PDP-433CMX, PDP-433MXE CONTENTS 1. SPECIFICATIONS ..........7 2. EXPLODED VIEWS AND PARTS LIST ....8 3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM ... 32 (For SCHEMATIC DIAGRAM, refer to ARP3124) 4. PCB CONNECTION DIAGRAM ... Refer to ARP3124 5. PCB PARTS LIST ..........54 6.
Page 7: Specifications
Power supply ..AC 100 - 120 V, 50/60 Hz (PDP-433CMX) RGB signal (G ON SYNC compatible) Power supply ..AC 100 - 240 V, 50/60 Hz (PDP-433MXE) RGB ... 0.7 Vp-p/75 Ω/no sync. Rated current ....2.98 A - 2.48 A (PDP-433CMX) HD/CS, VD ...
Page 8: Exploded Views And Parts List
PDP-433CMX, PDP-433MXE 2. EXPLODED VIEWS AND PARTS LIST • NOTES: Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List. • mark found on some component parts indicates the importance of the safety factor of the part.
Page 9 See Contrast table (2) (English/French/German) Remote Control Unit AXD1459 Ferrite Core See Contrast table (2) (2) CONTRAST TABLE PDP-433CMX/LUCB and PDP-433MXE/YVLDK are constructed the same except for the following : Part No. Mark Symbol and Description PDP-433CMX PDP-433MXE Remarks LUCB...
Page 10 PDP-433CMX, PDP-433MXE 2.2 UNDER LAYER SECTION (1) 5 or 6 Upper side 7 or 8...
Page 11 PDP-433CMX, PDP-433MXE • UNDER LAYER SECTION (1) PARTS LIST Mark No. Description Part No. ADR CONNECT A Assy AWZ6678 ADR CONNECT B Assy AWZ6679 ADR CONNECT C Assy AWZ6680 ADR CONNECT D Assy AWZ6681 BRIDGE A Assy AWZ6674 BRIDGE B Assy...
Page 12 PDP-433CMX, PDP-433MXE 2.4 UNDER LAYER SECTION (3) Upper side Upper side X DRIVE Assy Upper side Upper side...
Page 13 PDP-433CMX, PDP-433MXE • UNDER LAYER SECTION (3) PARTS LIST Mark No. Description Part No. DIGITAL VIDEO Assy AWV1941 X DRIVE Assy AWV1930 MX AUDIO Assy AWZ6644 Metal Fitting ANG2464 Heat Sink ANH1594 Silicone Sheet AEH1039 Insulation Sheet AMR3263 Audio Sheet (43)
Page 14 PDP-433CMX, PDP-433MXE 2.5 UNDER LAYER SECTION (4) Upper side Upper side Upper side...
Page 15 PDP-433CMX, PDP-433MXE • UNDER LAYER SECTION (4) PARTS LIST Mark No. Description Part No. Y DRIVE Assy AWZ6683 Circuit Board Spacer AEC1872 • • • • • • • • • • Scan IC Spring (43L) ABK1029 Scan IC Spring (43R)
Page 16 PDP-433CMX, PDP-433MXE 2.6 UNDER LAYER SECTION (5) Upper side 10 17 10 Fan Jumper Wire Saddle Wire Saddle • Bottom View...
Page 17 PDP-433CMX, PDP-433MXE • UNDER LAYER SECTION (5) PARTS LIST Mark No. Description Part No. THERMAL SENSOR Assy AWZ6639 Heat Sink ANH1594 Silicone Sheet AEH1039 Rivet BEC1066 Insulation Sheet AMR3263 Metal Fitting ANG2464 Wire Saddle AEC1904 PCB Spacer AEC1121 Circuit Board Spacer...
Page 18 PDP-433CMX, PDP-433MXE 2.7 UNDER LAYER SECTION (6) Upper side 27 30 A6 A7...
Page 19 PDP-433CMX, PDP-433MXE • UNDER LAYER SECTION (6) PARTS LIST Mark No. Description Part No. Mark No. Description Part No. ADR CONNECT A Assy AWZ6678 J202 Flexible Flat Cable ADD1183 ADR CONNECT B Assy AWZ6679 Flat Clamp AEC1879 ADR CONNECT C Assy...
Page 20 PDP-433CMX, PDP-433MXE 2.8 MIDDLE LAYER SECTION (1) Upper side Upper side Upper side Upper side • MIDDLE LAYER SECTION (1) PARTS LIST Mark No. Description Part No. Mark No. Description Part No. Front Chassis V (43) ANA1672 Front Chassis HU (43)
Page 21 PDP-433CMX, PDP-433MXE 2.9 MIDDLE LAYER SECTION (2) • MIDDLE LAYER SECTION (2) PARTS LIST Mark No. Description Part No. IR Assy AWZ6643 MX LED Assy AWZ6642 J113 Wire O ADX2778 KEY CONNECTOR Assy AWZ6695 IR Holder ANG2494 Nyron Rivet AEC1671...
Page 22 PDP-433CMX, PDP-433MXE 2.10 MIDDLE LAYER SECTION (3) Bottom Side RGB Assy J201 J202 • MIDDLE LAYER SECTION (3) PARTS LIST Mark No. Description Part No. RGB Assy AWZ6697 SLOT CONNECTOR Assy AWZ6634 Spacer AEC1065 Card Spacer AEC1882 RGB Base ANA1662...
Page 23 PDP-433CMX, PDP-433MXE 2.11 MIDDLE LAYER SECTION (4) Upper Rear Side Upper Side • MIDDLE LAYER SECTION (4) PARTS LIST Mark No. Description Part No. Mark No. Description Part No. Terminal Panel CMX ANG2486 Screw AMZ30P060FZK Slot Spring (Under) ABK1028 Screw...
Page 24 PDP-433CMX, PDP-433MXE 2.12 UPPER LAYER SECTION (1) J201 J201 J201 J202 J109 J113...
Page 25 PDP-433CMX, PDP-433MXE • UPPER LAYER SECTION (1) PARTS LIST Mark No. Description Part No. I/O Assy AWZ6631 CONTROL Assy AWZ6633 SP OUT R Assy AWZ6636 SP OUT L Assy AWZ6635 Power Switch (S1) BSM1006 AC Inlet with Filter (CN1) AKP1223...
Page 26 PDP-433CMX, PDP-433MXE 2.13 UPPER LAYER SECTION (2) PDP-433CMX Only 100V SW101 200V...
Page 27 ADX2738 Screw AMZ30P060FZK Silicone Sheet P AEH1035 Solder Warning Label See Contrast table (2) (2) CONTRAST TABLE PDP-433CMX/LUCB and PDP-433MXE/YVLDK are constructed the same except for the following : Part No. Mark Symbol and Description PDP-433CMX PDP-433MXE Remarks LUCB YVLDK...
Page 28 Screw ABZ30P050FZK Screw VMZ30P060FZK Energy Star Label AAX2856 Display Label See Contrast table (2) (2) CONTRAST TABLE PDP-433CMX/LUCB and PDP-433MXE/YVLDK are constructed the same except for the following : Part No. Mark Symbol and Description PDP-433CMX PDP-433MXE Remarks LUCB YVLDK...
Page 29 AAX2878 Terminal Display Label L (43) See Contrast table (2) Rear Corner Label AAX2862 Bottom View (2) CONTRAST TABLE PDP-433CMX/LUCB and PDP-433MXE/YVLDK are constructed the same except for the following : Part No. Mark Symbol and Description PDP-433CMX PDP-433MXE Remarks...
Page 30 PDP-433CMX, PDP-433MXE 2.16 PDP SERVICE ASSY 433 (AWU1043) PDP Service Assy 433 (AWU1043) consists of the following parts. • PARTS LIST Mark No. Description Part No. Mark No. Description Part No. Panel Chassis (43) Assy AWU1038 Insullation Sheet AMR3263 Front Chassis V (43)
Page 31 PDP-433CMX, PDP-433MXE Caution in Replacement of Chassis Block Please order the PDP Service Assy 433 (AWU1043) when replacing the Chassis block. PDP Service Assy 433 is all common use parts of for business, public use and module. Supply it by the state that installed Circuit Board Spacer (AEC1872) and Wire Saddle (AEC1904) as follows.
Page 32: Block Diagram And Schematic Diagram
PDP-433CMX, PDP-433MXE 3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM 3.1 BLOCK DIAGRAM 3.1.1 OVERALL BLOCK DIAGRAM Driver Driver Driver Driver Driver Driver Driver Driver Driver Driver Driver Driver Driver Driver Driver Driver VADR2 VADR2 CLK/LE IC6501 CLK/LE IC6601 VADR2 ADR CONNECT A...
Page 33 PDP-433CMX, PDP-433MXE Note : When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or "PCB PARTS LIST". Driver Driver Driver Driver Driver Driver Driver Driver Driver Driver Driver Driver Driver Driver Driver Driver VADR2 VADR2...
Page 34 PDP-433CMX, PDP-433MXE 3.1.2 RGB ASSY IC5102 (PE5066ACK) SD RAM IC101 SD RAM VCLK(132) DEO(99) HDO(98) VDO(97) RAO[0:7]RBO[0:7] GAO[0:7]GBO[0:7] (LCX541) BAO[0:7]BBO[0:7] Selector IC5001 Buffer (???????) IC102 I/O ASSY (LCX125) CLK SEL IC4603 IC4004 (CXA3516R) 13.5V V+12V V+12V A/D PLL AMP HOLD...
Page 35 PDP-433CMX, PDP-433MXE DIGITAL VIDEO ASSY SD RAM SD RAM RGB ASSY 100MHz X'tal RA[0:9]RB[0:9] GA[0:9]GB[0:9] MCLKI(242) BA[0:9]BB[0:9] IC31 CLKOUT(88) (1/2) RAI[0:7]RBI[0:7] DEO(92) GAI[0:7]GBI[0:7] HDO(91) VD Shift BAI[0:7]BBI[0:7] OSDH(62) VDO(90) CLKI(286) HDI(297) IC5301 IC5602 DEI(296) VDI(299) (PD6357B) (MEM29L800TA-90PFIN) IC30 HIS(300) Flash ROM...
Page 36 PDP-433CMX, PDP-433MXE 3.1.3 DIGITAL VIDEO ASSY RGB ASSY DIGITAL VIDEO ASSY 3.3V 2.5V 3.3V IC1301 (IC31 L) (PD6358) Address Data RGB 2 phase 10 bit DRAM ADR CONNECT A - D Assy (Left section) Line IC5301 Buffer (PD6357) IC30 IC1401 (IC31 R)
Page 37 PDP-433CMX, PDP-433MXE 3.1.4 X DRIVE ASSY...
Page 38 PDP-433CMX, PDP-433MXE 3.1.5 Y DRIVE ASSY IC5V IC2504 Photo Coupler TC74ACT540FT Photo Coupler Photo Coupler OC2-1 To SCAN ASSY Photo Coupler (Lower) Photo Coupler Photo Coupler IC2501,IC2502, IC2001 IC2505,IC2510, TC74ACT541FT IC2512,IC2513, IC2514,IC2525, HCPL-M611 To SCAN ASSY (Upper) IC2506 TC74ACT540FT OC2-2...
Page 39 PDP-433CMX, PDP-433MXE VSUS Q2204 YPR-U1 YPR-U2 Q2205 IC2203 TND301S K2203 SUSOUT A 37-40 IC2212 TND301S 29,30 Q2219 K2220 PSUS Q2218 Q2215 Y CONNECTOR IC2213 ASS'Y TND301S Vsus Q2221 Q2220 K2212 SUSOUT B 37-40 IC2216 TND301S 29,30 Q2217 Q2226 Q2227 IC2217...
Page 40 PDP-433CMX, PDP-433MXE 3.1.6 MX AUDIO ASSY...
Page 41 PDP-433CMX, PDP-433MXE 3.1.7 SUB ADDRESS A and B ASSYS +60V Current - Voltage Over Current DET. Block Convert Block ADRGND CN8801 R8801 - R8805 Q8801 H : V MID CLAMP OFF L : V MID CLAMP ON ADR Output P.D. Output Block...
Page 42 PDP-433CMX, PDP-433MXE 3.1.8 ADR RESONANCE ASSY CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. REPLACE ONLY WITH SAME TYPE NO. ICP-S1.0 MFD +60V BY ROHM CO., LTD. FOR IC6704. +60V +60V ICP-S1, 0 +60V CN6702 IC6704 C6703 - C6708...
Page 43 PDP-433CMX, PDP-433MXE 3.1.10 VIDEO SIGNAL ROUTE...
Page 44 PDP-433CMX, PDP-433MXE 3.1.11 SYNC SIGNAL ROUTE...
Page 45 PDP-433CMX, PDP-433MXE 3.2 WAVEFORMS RGB ASSY CH1 : IC5505 - pin 29 (SCL) CH1 : IC5505 - pin 1 (TXD) CH2 : IC5505 - pin 30 (SDA) CH2 : IC5505 - pin 2 (CLK) V: 5V/div. H: 500µsec/div. V: 5V/div. H: 100µsec/div.
Page 46 PDP-433CMX, PDP-433MXE DIGITAL VIDEO ASSY K1327 (VDI) K1326 (DEI) K1308 (VDRB) K1328 (HDI) K1333 (VCLKL) IC1501 - pin 15 (LBLK) V: 2V/div. H: 4msec/div. V: 2V/div. H: 4µsec/div. V: 2V/div. H: 2msec/div. K1327 (VDI) K1326 (DEI) K1308 (VDRB) K1328 (HDI)
Page 47 PDP-433CMX, PDP-433MXE ADR CONNECT A - D SUB ADDRESS A, B RESONANCE ASSY ASSY ASSY CH1 : IC6702 - pin 2 CH1 : IC6501 - pin 8 (CLK) CH1 : IC8801 - pin 3 CH2 : IC6701 - pin 2...
Page 48 PDP-433CMX, PDP-433MXE VIDEO CARD (PDA-5002) IC7002 - pin 7 (VY) K7301 (CR) CH1 : IC7408 - pin 14 (VD_PLK) CH1 : IC7408 - pin 18 (CLK_PLK) V: 200mV/div. H: 20µsec/div. V: 200mV/div. H: 20µsec/div. CH2 : IC7408 - pin 15 (HD_PLK)
Page 49 PDP-433CMX, PDP-433MXE RGB VIDEO Signal Waveforms Waveform at Power ON Reset 2, D+2.5V, D+3.3V A+3.3V, D+2.5V, D+3.3V Wide UCOM, Reset 2, D+3.3V IC100 clk, Reset 2, D+3.3V V: 2V/div. H: 20msec/div. V: 2V/div. H: 50msec/div. V: 2V/div. H: 20msec/div. V: 2V/div. H: 20msec/div.
Page 50 PDP-433CMX, PDP-433MXE Information Point Information Trigger Signal (CH4) CN4103 - pin 2 Synchronize with K4805 (HD_PLL) Synchronize with K4805 (HD_PLL) CN4004 - pin 1 Synchronize with K4805 (HD_PLL) IC4402 - pin 17 IC4603 - pin 133 Synchronize with K4805 (HD_PLL)
Page 51 PDP-433CMX, PDP-433MXE CN4103 - pin 2 IC5301 - pin 276 IC4603 - pin 113 CN5702 - pin 26 V: 200mV/div. H: 10µsec/div. V: 1V/div. H: 10µsec/div. V: 2V/div. H: 10µsec/div. V: 2V/div. H: 10µsec/div. CN4004 - pin 1 IC5701 - pin 30...
Page 52 PDP-433CMX, PDP-433MXE IC4803 - pin 11 IC4402 - pin 31 K5314 (DE_SEL), K5315 (HD_SEL), K5314 (DE_SEL), K5315 (HD_SEL), V: 200mV/div. H: 4msec/div. V: 200mV/div. H: 4msec/div. K5316 (VD_SEL), K5317 (HD_30) K5316 (VD_SEL), K5317 (HD_30) V: 5V/div. H: 2msec/div. V: 5V/div. H: 2msec/div.
Page 53 PDP-433CMX, PDP-433MXE Sustain Waveforms Drive Pulse Waveforms Sustain Waveform (1 field) Reset Waveform Y Drive Pulse Control Waveform (1 field) ch 1 : K3107 (X.PSUS) - K3201 (SUSGND) ch 1 : K3107 (X.PSUS) - K3201 (SUSGND) V: 100V/div. H: 2msec/div.
Page 54: Pcb Parts List
PDP-433CMX, PDP-433MXE Mark No. Description Part No. Mark No. Description Part No. 5. PCB PARTS LIST NOTES : ÷ Parts marked by “ NSP ” are generally unavailable because they are not in our Master Spare Parts List. ÷ The mark found on some component parts indicates the importance of the safety factor of the part.
Page 55 PDP-433CMX, PDP-433MXE Mark No. Description Part No. Mark No. Description Part No. SCAN (B) ASSY BRIDGE B ASSY SEMICONDUCTORS SEMICONDUCTOR IC6001-IC6006 SN755860PJ D6431 D1FL20U(S) CAPACITORS CAPACITOR C6001,C6002,C6011,C6012 ACG1088 C6431 (0.1µF/100V) ACG1098 (0.1µF/250V) C6021,C6022,C6031,C6032 ACG1088 OTHERS (0.1µF/250V) CN6431 PH CONNECTOR B4B-PH-SM3...
Page 56 PDP-433CMX, PDP-433MXE Mark No. Description Part No. Mark No. Description Part No. ADR CONNECT B ASSY ADR CONNECT D ASSY SEMICONDUCTORS SEMICONDUCTORS IC6601 TC74VHC541FT IC6901 TC74VHC541FT Q6602 2SC2712 Q6902 2SC2712 Q6603 2SK209 Q6903 2SK209 D6601 DA227 D6901 DA227 COILS COILS L6601,L6602 (22µH/0.11A)
Page 57 PDP-433CMX, PDP-433MXE Mark No. Description Part No. Mark No. Description Part No. X DRIVE ASSY CAPACITORS C3205,C3206,C3212,C3213 (1.5µF) ACE1160 [X LOGIC BLOCK] C3225,C3226 (1.5µF) ACE1160 C3131,C3139,C3143 (0.1µF/630V) ACG1092 SEMICONDUCTORS C3223,C3224 (100pF/500V) ACG1100 IC3003 PE1012A C3132 (47µF/350V) ACH1346 IC3004 TC74ACT540FT IC3001,IC3008...
Page 58 PDP-433CMX, PDP-433MXE Mark No. Description Part No. Mark No. Description Part No. TRANSFORMER [Y DRIVE SUS BLOCK] T3701 ATK1153 SEMICONDUCTORS IC2202,IC2208 HCPL-M611 CAPACITORS IC2206,IC2214 STK795-460 C3701 (22µF/315V) ACH1345 IC2201 TC74ACT541FT C3717 (47µF/315V) ACH1346 IC2203,IC2204,IC2210,IC2212 TND301S C3704 CEHAT101M16 IC2213,IC2216,IC2217 TND301S C3706,C3711,C3714...
Page 59 PDP-433CMX, PDP-433MXE Mark No. Description Part No. Mark No. Description Part No. R2358-R2361 RS1/16S3300F D2711 D1FS4 R2263,R2264 RS1/2S100J D2725 EC8FS6 R2203 RS1/2S102J D2733 RD110P R2209 RS1/2S2R2J D2724 U1ZB330 R2202 RS1/2S561J D2713 U1ZB36 R2278,R2303 RS1MMF101J D2740 UDZ12B R2233,R2234 RS1MMF152J D2709,D2716 UDZ3.6B...
Page 60 PDP-433CMX, PDP-433MXE Mark No. Description Part No. Mark No. Description Part No. SLOT CONNECTOR ASSY COILS L8901 CHOKE COIL (100µH/0.45A) ATH1074 OTHERS L8902,L8903 COIL (22µH/0.11A) ATH1081 CN8102 SOCKET 120P AKP1219 CN8101 PCI SOCKET 120P AKP1220 CAPACITORS KN8101,KN8102 GROUND PLATE ANK1664...
Page 61 PDP-433CMX, PDP-433MXE Mark No. Description Part No. Mark No. Description Part No. [PANEL UCOM BLOCK] OTHERS X1201 CERAMIC RESONATOR ASS1159 SEMICONDUCTORS (16MHz) IC1101 HD64F2328VF CN1203 PH CONNECTOR B3B-PH-SM3 IC1103 NC7SZ08P5 CN1201,CN1202 8P PLUG CKS3130 IC1102 PST9228N Q1101,Q1103 DTC143EK D1101 AEL1171...
Page 62 PDP-433CMX, PDP-433MXE Mark No. Description Part No. Mark No. Description Part No. K1333,K1501,K1502,K1601,K1602 AKX9002 [RGB I/O BLOCK] TEST PIN SEMICONDUCTORS K1728,K1729 TEST PIN AKX9002 CN1503,CN1603 PH CONNECTOR B8B-PH-SM3 IC4110 24LCS21A CN1301 8P PLUG CKS3130 IC4108 BA7657F IC4107,IC4111 LT1399CS CN1702 30P CONNECTOR...
Page 63 PDP-433CMX, PDP-433MXE Mark No. Description Part No. Mark No. Description Part No. C4651,C4652,C4656,C4668 CEHAT101M10 RGB ASSY C4622 CFTLA105J50 C4662 CKSRYB102K50 [MATRIX BLOCK] C4608,C4619,C4627,C4628 CKSRYB104K16 SEMICONDUCTORS C4634,C4635,C4639,C4640 CKSRYB104K16 IC4402 CXA2101AQ C4610,C4647 CKSRYB105K6R3 IC4403 ML6426CS-1 C4675 CKSRYB184K10 IC4404 NJM072BM-E C4601,C4605,C4606,C4609 CKSRYF104Z16 Q4407-Q4409...
Page 64 PDP-433CMX, PDP-433MXE Mark No. Description Part No. Mark No. Description Part No. RESISTORS [IC30 BLOCK] R4814,R4818,R4835,R4915 RAB4C101J SEMICONDUCTORS R4913 RAB4C102J IC5302,IC5303 MS82V16520-8GA R4809 RAB4C152J IC5301 PD6357B R4825 RAB4C471J R4808,R4943 RAB4C472J CAPACITORS R4864 RS1/16S1802F C5301,C5308 CEHAT101M10 R4865 RS1/16S2702F C5302-C5307,C5309-C5322,C5324 CKSRYF104Z16 R4868...
Page 65 PDP-433CMX, PDP-433MXE Mark No. Description Part No. Mark No. Description Part No. [WIDE UCOM BLOCK] CAPACITORS C8602,C8617 CEAT101M16 SEMICONDUCTORS C8606,C8607 CEAT101M25 IC5601 HD64F2328VF C8610 CEAT221M16 IC5604 NC7SZ08P5 C8605,C8613,C8614 CEAT470M35 IC5603 PST9228N C8609,C8615,C8622 CEAT471M25 IC5605 TC7SH32FU IC5607,IC5608 TC7WH74FU C8611,C8618 CEAT4R7M50 C8612,C8619...
Page 66 PDP-433CMX, PDP-433MXE Mark No. Description Part No. Mark No. Description Part No. CAPACITORS SP OUT R ASSY C8001,C8002,C8005,C8006 CEAT1R0M50 COILS C8003,C8010 CEAT470M16 C8004,C8007,C8008 CKSRYB103K50 L8176,L8177 CHOKE COIL ATH1073 C8009 CKSRYB472K50 CAPACITORS RESISTORS C8182,C8183 CCSRCH101J50 R8006 RAB4C102J C8179 CCSRSL221J50 Other Resistors...
Page 67 PDP-433CMX, PDP-433MXE Mark No. Description Part No. Mark No. Description Part No. IR ASSY SEMICONDUCTORS Q8551 2SC2712 D8552 1SS226 D8551 1SS355 CAPACITORS C8551 CEV470M6R3 C8553 CKSQYB472K50 C8552 CKSRYB103K50 C8554 CKSRYF104Z16 RESISTORS All Resistors RS1/16S OTHERS 8551 REMOTE RECEIVER UNIT GP1UM26RK...
Page 68: Adjustment
PDP-433CMX, PDP-433MXE 6. ADJUSTMENT 6.1 SERVICE FACTORY MODE Perform the operations of Service Factory mode using the Remote Control Unit provided with the Plasma Display (AXD1459). 6.1.1 State Transition Diagram Normal Operation At standby Mode (within 3 sec.) "Menu" key (AA8B) STANDBY/ON (AA1C) ‘...
Page 69 PDP-433CMX, PDP-433MXE • AXD1459 (PDP-503CMX / PDP-433CMX) POWER POWER MENU SCREEN DISPLAY CALL SIZE SCREEN SIZE FULL AUTO FULL AUTO ZOOM ZOOM DISPLAY CALL SURROUND MUTE MODE MUTE SOUND AUDIO SOUND VOLUME MENU VOLUME AV MEMORY SURROUND MODE AV SELECT AUDIO •...
Page 70 PDP-433CMX, PDP-433MXE Caution of Operation of the Remote Control Unit • In the service factory mode, use the key which does not exist in a remote control unit (AXD1459) attached to this product as the direct selection key of item when selects each item. These keys can use with the attached remote control units (AXD1432 and AXD1673) in the PDP-501HD and PDP-502HD.
Page 71 PDP-433CMX, PDP-433MXE 6.1.2 Adjustment Items Table of Service Factory SLOT Adjustment Range Name OSD Display Name RS-232C Command Service Factory Operation (OFFSET Reference Value) Y-DELAY REF/OFS-SLOT-1 0 to 15 [8] YOUTLEV Y-OUT LEVEL REF/OFS-SLOT-2 0 to 63 [32] TINT CD TINT...
Page 72 PDP-433CMX, PDP-433MXE COLOR TEMP (VIDEO OPTION) Adjustment Range Name OSD Display Name RS-232C Command Service Factory Operation (OFFSET Reference Value) COLOR COLOR VOP-CT-3 0 to 255 [128] IC102 TINT TINT VOP-CT-4 0 to 255 [128] MCONTRAST CONTRAST VOP-CT-1 0 to 255 [128]...
Page 73 PDP-433CMX, PDP-433MXE 6.1.3 Display Description of Service Factory Menu 1. In Adjustment Item ∗ O F S – S L O T – – I N 4 – 0 4 – Display color : White Halftone : Blue (second row/15th row...
Page 74 PDP-433CMX, PDP-433MXE 2. INFORMATION ∗ I N F O – – I N 4 – 0 2 – V E R S I O N ∗ ∗ ∗ M A I N U C O M ∗ ∗ ∗ W I D E U C O M ∗...
Page 75 PDP-433CMX, PDP-433MXE 3. OSD Display in INFORMATION VERSION ∗ I N F O – – I N 4 – 0 2 – V E R S I O N ∗ ∗ ∗ M A I N U C O M ∗...
Page 76 PDP-433CMX, PDP-433MXE TEMPERATURE ∗ I N F O – – I N 4 – 0 2 – • Each display is the value of A/D input or D/A output of the microcomputer (0 to 255). T E M R A T •...
Page 77 PDP-433CMX, PDP-433MXE 4. REFERENCE ∗ R E F – – I N 4 – 0 2 – Display color : White Halftone : Blue (Second row / 15th row for each 1th to 32th columns) R G B 1 Basic Operation •...
Page 78 PDP-433CMX, PDP-433MXE REFERENCE — RGB1 ∗ R E F – R G B 1 – – I N 4 – 0 2 – Display color : White Half tone : Blue (second row / 15th row for each 1 to 32th columns) ∗...
Page 79 PDP-433CMX, PDP-433MXE REFERENCE — RGB2 ∗ R E F – R G B 2 – – I N 4 – 0 2 – Display color : White Half tone : Blue (second row / 15th row for each 1 to 32th columns) ∗...
Page 80 PDP-433CMX, PDP-433MXE REFERENCE — DIGITAL ∗ R E F – D I G – – I N 4 – 0 2 – Display color : White Half tone : Blue (second row / 15th row for each 1 to 32th columns) ∗...
Page 81 PDP-433CMX, PDP-433MXE REFERENCE — SLOT (At Connected SLOT ST1) • This mode is effective for SLOT ST1 only in connection ∗ Display color : White R E F – S L O T – – I N 4 – 0 2 –...
Page 82 PDP-433CMX, PDP-433MXE 5. OFFSET ∗ O F S – – I N 4 – 0 2 – Display color : White Half tone : Blue (second row / 15th row for each 1 to 32th columns) R G B 1...
Page 83 PDP-433CMX, PDP-433MXE OFFSET — RGB1 ∗ O F S – R G B 1 – – I N 4 – 0 2 – Display color : White Half tone : Blue (second row / 15th row for each 1 to 32th columns) ∗...
Page 84 PDP-433CMX, PDP-433MXE OFFSET — RGB2 O F S – R G B 2 – – I N 4 – 0 2 – Display color : White Half tone : Blue (second row / 15th row for each 1 to 32th columns)
Page 85 PDP-433CMX, PDP-433MXE OFFSET — DIGITAL ∗ O F S – D I G – – I N 4 – 0 2 – Display color : White Half tone : Blue (second row / 15th row for each 1 to 32th columns) ∗...
Page 86 PDP-433CMX, PDP-433MXE OFFSET — SLOT (At Connected SLOT ST1) • This mode is effective for SLOT ST1 only in connection ∗ O F S – S L O T – – I N 4 – 0 2 – Display color : White...
Page 87 PDP-433CMX, PDP-433MXE 6. VIDEO OPTION V I D E O O P T – – I N 4 – 0 2 – Display color : White Half tone : Blue (second row / 15th row for each 1 to 32th columns)
Page 88 PDP-433CMX, PDP-433MXE Operating specification • Start from SIDE MASK LEVEL (Key 1) when shifted to this setting screen. However, the movement original item to be selected when shifted from the lower layer. • When each key was pressed, follow the required operation.
Page 89 PDP-433CMX, PDP-433MXE SIDE MASK LEV. Adjustment ∗ V O P – M A S K – – I N 4 – 0 2 – Display color : White Half tone : Blue (second row / 15th row for each 1 to 32th columns) ∗...
Page 90 PDP-433CMX, PDP-433MXE COLOR MODE2 Adjustment ∗ V O P – M O D E 2 – – I N 4 – 0 2 – COLOR MODE indication of second row/31th columns displays the default. (It is not controlled with the COLOR MODE in adjustment.)
Page 91 PDP-433CMX, PDP-433MXE COLOR TEMP Adjustment Display color : White ∗ V O P – M I D – – I N 4 – 0 2 – Half tone : Blue (second row / 15th row for each 1 to 32th columns) ∗...
Page 92 PDP-433CMX, PDP-433MXE 7. INITIALIZE ∗ I N I T – – I N 4 – 0 2 – Display color : White Half tone : Blue (second row / 15th row for each 1 to 32th columns) C O L O R...
Page 93 PDP-433CMX, PDP-433MXE Operating specification • Start from COLOR DET (Key 1) when shifted to this setting screen. However, the movement original item to be selected when shifted from the lower layer. • When each key was pressed, follow the required operation.
Page 94 PDP-433CMX, PDP-433MXE : YES/NO selection ∗ I N I T – – I N 4 – 0 2 – : Store the SET DATA at YES selection and shift to INIT screen. Hold the NOW DATA at NO selection and shift to INIT screen.
Page 95 PDP-433CMX, PDP-433MXE 16. MEMO: Display and edit the memo data. <MEMO/SELECT> ∗ • Select MEMO to edit with 5∞ keys. I N I T – – I N 4 – 0 2 – • Shift to the <MEMO/EDIT> screen with the SET key.
Page 96 PDP-433CMX, PDP-433MXE FINAL SETUP Details Items Initial Setting Remarks Key Remote control input Power supply (STANDBY/ON) NO CARE Input function INPUT1 VIDEO WIDE (In the video signal input) Every each input function 1 DOT BY DOT (In the PC signal input) Every each input function...
Page 97 PDP-433CMX, PDP-433MXE Items Initial Setting Remarks FULL MASK R LEVEL Default value SIDE MASK G LEVEL Default value B LEVEL Default value Set is common MASK CONTROL ORBITER MODE INVERSE MODE COLOR MODE MODE1 Set is common MIRROR MODE FAN CONTROL AUTO &&&PLASMA&&&...
Page 98 PDP-433CMX, PDP-433MXE MASK1 ∗ I N I T – M A S K – – I N 4 – 0 2 – Display color : White Half tone : Blue (second row / 15th row for each 1 to 32th columns)
Page 99 PDP-433CMX, PDP-433MXE MASK2 ∗ I N I T – M A S K – – I N 4 – 0 2 – Display color : White Half tone : Blue (second row / 15th row for each 1 to 32th columns)
Page 100 PDP-433CMX, PDP-433MXE Cassification 1 of Input Signal Mode (VIDEO) INPUT5 V. Frequency H. Frequency Display Pixel (DVI input) SIG Mode Signal Type OSD display fv (Hz) fh (Hz) Number Correspondence 784 × 768 4 : 3 • 1024 × 768 FULL •...
Page 101 PDP-433CMX, PDP-433MXE Classification 2 of Input Signal Mode (PC) INPUT5 V. Frequency H. Frequency Display Pixel SIG Mode Signal Type OSD Display (DVI input) v (Hz) h (Hz) Number Correspondence 640 × 400 1024 × 768 × (non-correspondence) 20 • 2 FULL 24.8...
Page 102 PDP-433CMX, PDP-433MXE INPUT5 V. Frequency H. Frequency SIG Mode Signal Type OSD Display Display Pixel (DVI input) v (Hz) h (Hz) Number Correspondence 768 × 768 81 • 1 4 : 3 (TYPE) 1152 × 864 ? (correspondence) 53.7 1024 × 768 81 •...
Page 103 PDP-433CMX, PDP-433MXE 6.2 ADJUSTMENT REQUIRED WHEN THE SET IS REPAIRED OR REPLACED RGB Assy Y DRIVE Assy When repaired When repaired 1. Adjustment is impossible when replaced the Matrix IC or 1. VOFS/VH/IC5V voltage adjustment AD/PLL/AMP IC. 2. Timing adjustment of pulse module 2.
Page 104 PDP-433CMX, PDP-433MXE 6.3 ADJUSTMENT 6.3.1 Main Unit Adjustment VOFS/VH/IC5V Voltage Adjustment Adjusting Point Input Signal Adjusting Method VOFS (Offset voltage) adjustment Method 1 1. Write down a adjustment value of V-OFFSET of REF-DIG mode in the factory mode. 2. Set this adjustment value to center (128).
Page 105 PDP-433CMX, PDP-433MXE Sustain Pulse Waveform Adjustment Adjusting Point Adjusting Method Input Signal REF_DIG mode in Factory mode X-SUS-B, Y-SUS-B Adjustment White 100% X-SUS-B : key 9 Set to the indicated value with a key on the remote control unit. Y-SUS-B : key 11 (Refer to "Timing adjustment of control signal of X and Y Drive Assys".)
Page 106 PDP-433CMX, PDP-433MXE Color Balance Adjustment Adjusting Point Adjusting Method Input Signal REFERENCE1 mode Color Balance Adjustment in Factory mode Fresh color After adjusting the white balance, check the flesh color of figures in LD still pictures. If the color COLOR : key 3 is not natural, adjust it with the keys on the remote control unit.
Page 107 PDP-433CMX, PDP-433MXE Timing Adjustment of X and Y DRIVE Assys Control Signal Purpose • Pulse module loads in DRIVE Assy as one of heat measures of DRIVE Assy. Adjust the drive timing of the pulse module driving parallel with VR.
Page 108 PDP-433CMX, PDP-433MXE Measuring Waveform of Pulse Module Timing Adjustment Timing adjustment of the pulse module control signal adjusts with the sustain pulse of eighth pulse (X DRIVE) and the ninth pulse (Y DRIVE) from the back of 6SF. Measuring point of waveform...
Page 109 PDP-433CMX, PDP-433MXE SUS-D Adjustment (Y DRIVE) SUS-U Adjustment (Y DRIVE) 1ms/div 1ms/div Magnify 6SF block Magnify 6SF block 5µs/div 5µs/div Magnification Magnification 1ms/div 1ms/div Magnify 6SF block Magnify 6SF block 500ns/div 200ns/div Magnification Magnification 1ms/div 1ms/div Magnify 6SF block Magnify 6SF block...
Page 110 PDP-433CMX, PDP-433MXE SUS-B Ground Timing Adjustment It is necessary to readjust this adjustment when replaced the X or Y DRIVE Assy and the pulse module. Measurement point and method Measurement point X DRIVE Assy : SUSOUT A : K3105 , GND : K3201...
Page 111 PDP-433CMX, PDP-433MXE Y DRIVE Assy X DRIVE Assy K2720 K2716 K3708 K3213 (PSUS) (VH) (VRN_OVP) (1/2VSUS) K2218 K3214 K2215 K2217 K3702 K2717 K3707 (1/2 VSUS) (SUSGND) (SUS_B) (SUS_U) (SUS. GND) K3706 (VH CONT) (VRN) (X DC-DC PD) K2214 (SUS_G) K2216...
Page 112 PDP-433CMX, PDP-433MXE 6.4 COMMAND 6.4.1 RS-232C COMMAND (for adjustment) Ο − − Ο Ο Ο Ο − Ο Ο Ο Ο − Ο Ο Ο Ο − Ο Ο Ο Ο − Ο Ο Ο − − Ο Ο Ο...
Page 113 PDP-433CMX, PDP-433MXE 6.4.2 RS-232C COMMAND (for setting) − Ο − − − − − Ο − − Ο Ο Ο − − Ο Ο Ο − − Ο − − − − Ο − − − − Ο − −...
Page 114 PDP-433CMX, PDP-433MXE Ο Ο Ο − − y t i Ο − − − − Ο Ο − − − Ο Ο − − − Ο − − Ο − i t l Ο Ο − − − Ο Ο...
Page 115 PDP-433CMX, PDP-433MXE Ο Ο Ο − − r r i Ο Ο Ο − − Ο Ο Ο − − Ο Ο Ο − − Ο Ο Ο − − Ο Ο Ο − − Ο Ο − − −...
Page 116 PDP-433CMX, PDP-433MXE 6.4.3 GET Command Command Description Command Function Output data of an electronic VR adjustment value and a drive system adjustment value Output data to be related to white balance adjustment of the panel Output data such as version information, hour meter and pulse meter...
Page 117 PDP-433CMX, PDP-433MXE GS1: Output data such as version information, hour meter and pulse meter • Output it according to transmission order and size of the table below. • Command is invalid except RS-232C factory adjustment mode. Order Data Contents Size...
Page 118 PDP-433CMX, PDP-433MXE GS2: Output data of power down, temperature and dew drop information • Output it according to transmission order and size of the table below. • In the PD (Power Down) of RS-232C factory adjustment mode, NG except dew drop and AUDIO occurs and a command that except for 30 seconds to SD (shut down) is invalid.
Page 119 PDP-433CMX, PDP-433MXE GAS (Get Adjust Slot): Output data to be related to picture quality setting • Transmit data according to transmission order and size of the table below. • Data are SLOT sections of the factory menu. • When current input function is except for VIDEO input of SLOT system, command is invalid.
Page 120 PDP-433CMX, PDP-433MXE GAR: Output data to be related to picture quality (RGB1 of the factory menu) • Transmit data according to transmission order and size of the table below. • Command is invalid except RS-232C factory adjustment mode. Order Data Contents...
Page 121 PDP-433CMX, PDP-433MXE (Get Power Down), PD (Power Down) Outputs information (contents of PD INFORMATION of service factory MENU) • Output the acquired data according to the transmission order and size of the table below. • Except RS-232C factory adjustment mode and PD state, command is invalid.
Page 122 PDP-433CMX, PDP-433MXE GWB (Get White Balance): Output data to be related to picture quality / white balance • Transmit data according to transmission order and size of the table below. • Except each normal operation mode / RS-232C integrator adjustment / RS-232C factory adjustment mode, command is invalid.
Page 123 PDP-433CMX, PDP-433MXE GSS: Output data to be related to various established state (SET UP item of menu mode / integrator menu) • Transmit data according to transmission order and size of the table below. • Except each normal operation mode / RS-232C integrator adjustment / RS-232C factory adjustment mode, command is invalid.
Page 124 PDP-433CMX, PDP-433MXE GSO: Output data to be related to various established state (OPTION item of menu mode / integrator menu) • Transmit data according to transmission order and size of the table below. • Except each normal operation mode / RS-232C integrator adjustment / RS-232C factory adjustment mode, command is invalid.
Page 125: General Information
PDP-503CMX, PDP-503MXE, PDA-5002 7. GENERAL INFORMATION 7.1 DIAGNOSIS 7.1.1 PCB LOCATION ADR CONNECT A Assy DIGITAL VIDEO Assy BRIDGE A Assy ADR CONNECT B THERMAL Assy SENSOR SUB ADDRESS A Assy Assy RESONANCE Assy SCAN (B) Assy ADR CONNECT C Assy Y DRIVE SW POWER SUPPLY...
Page 126: Shut Down/Power Down Diagnosis By Led Display
PDP-433CMX, PDP-433MXE 7.1.2 SHUT DOWN/POWER DOWN DIAGNOSIS BY LED DISPLAY When internal circuit abnormality and other operation abnormality occurred from this unit, self-diagnose display function by STANDBY/ON (LED) indicator is loaded. Each NG point by LED blinking and a PD (power down) point are as follows.
Page 127 PDP-433CMX, PDP-433MXE Block Diagram of Shut Down Signal System...
Page 128 PDP-433CMX, PDP-433MXE Shut down diagnosis 1 Panel microcomputer NG 30 32 When a module microcomputer failed in communication with a panel microcomputer, this NG occurs. Shut down after OSD display for 30 seconds from the NG detection. Abnormality to expect...
Page 129 PDP-433CMX, PDP-433MXE 5 FAN NG 30 32 When a fan does not function, this NG occurs. Shut down after OSD display for 30 seconds from the NG detection. * FAN NG detection functions only in case of following. • When FAN CONTROL setting is maximum WAR N I NG •...
Page 130 PDP-433CMX, PDP-433MXE Block Diagram of Power Down Signal System...
Page 131 2.5V OVP P.D. by 2.5V overvoltage 2.5V UVP P.D. by 2.5V undervoltage (= overcurrent) Reference OVP : Over Voltage Protect UVP : Under Voltage Protect OCP : Over Current Protect Note 1: AC200V P.D. is not applicable to the PDP-433MXE model.
Page 132 PDP-433CMX, PDP-433MXE Diagnosis Method in Power Down 1st/2nd/time stamp are stored eight times of power down in the past. 1 OSD display of PD history Display with "INFORMATION" of the factory menu. Display of PD point 30 32 Power Down Point OSD Display ∗...
Page 133 PDP-433CMX, PDP-433MXE...
Page 134 PDP-433CMX, PDP-433MXE Block diagram for Power supply section SW POWER SUPPLY MODULE Y DRIVE ASSY VOFS VOFS DC/DC -45V Converter +B395V VSUS AC IN Power Factor VSUS DC/DC 100 - 240V Control Converter 215V VH DC/DC 130V Converter VADR VADR DC/DC...
Page 135: Automatic Backup Of Digital Video Assy Data
PDP-433CMX, PDP-433MXE 7.1.3 AUTOMATIC BACKUP OF DIGITAL VIDEO ASSY DATA Description Auto copies data of EEPROM (IC1204/2k bit) on the DIGITAL VIDEO Assy as data for backup in the Assy replacement to one part of EEPROM (IC5502/64k bit) of the RGB Assy (area A of figure below).
Page 136 PDP-433CMX, PDP-433MXE Actual automatic backup operation 1. In the DIGITAL VIDEO Assy replacement (Use the service Assy) Do not need modification of key words. Replace DIGITAL VIDEO Assy with DIGITAL VIDEO Assy for service, and auto copies the backup data from EEPROM of RGB Assy to EEPROM of DIGITAL VIDEO Assy by turning the power on.
Page 137: Disassembly
PDP-433CMX, PDP-433MXE 7.1.4 DISASSEMBLY SW Power Supply Module Remove the Rear Case (M). (Screws × 20) Insert the SW Power Supply Module into the slit of Sub Frame L and R. ×2 ×2 ×2 ×2 Slit SW Power Supply Module...
Page 138 PDP-433CMX, PDP-433MXE DIGITAL VIDEO Assy Remove the Rear Case (M). (Screws × 20) Remove the DIGITAL VIDEO Assy. (Connector, Circuit Board Spacer × 6) Remove the SW Power Supply Module. (Connector, Screws × 4) Remove a screw of earth block.
Page 139 PDP-433CMX, PDP-433MXE Y DRIVE, SCAN (A) and (B) Assemblies Remove the Rear Case (M). (Screws × 20) Remove the three screws. Remove the Y DRIVE Assy. (Connector, PCB Spacer × 3, Screws × 8) Remove the Front Chassis V. (Screws × 5) Remove the Scan IC Spring 43L and 43R.
Page 140 PDP-433CMX, PDP-433MXE X DRIVE Assy Diagnosis of the Video Card (PDA-5002) Remove the Rear Case (M). (Screws × 20) Remove the Rear Case (M). (Screws × 20) Remove the X DRIVE Assy. (Connector, Screws × 8) Remove the Video Card. (Screws × 2) Remove the SLOT CONNECTOR Assy from the RGB Assy and reconnect it with the Jig Cable (GGD1035).
Page 141: Ic Information
PDP-433CMX, PDP-433MXE 7.2 IC INFORMATION ¶ The information shown in the list is basic information and may not correspond exactly to that shown in the schematic diagrams. • List of IC SN755860PJ, M30624FGAFP, HD64F2328VF, GAL22V10, M30624FGAFP, PD6358A, PST9246N, FS781BZB, ML6426CS-1,...
Page 142 PDP-433CMX, PDP-433MXE • Block Diagram • Pin Function...
Page 143 PDP-433CMX, PDP-433MXE M30624FGAFP (RGB ASSY : IC5505) • Main Microcomputer • Pin Function Pin Name Function Serial 3 line data output Serial 3 line clock FAN control Audio VOL control H_SYNC Horizontal synchronizing signal input for signal distinction V_SYNC Vertical synchronizing signal input for signal distinction...
Page 144 PDP-433CMX, PDP-433MXE Pin Name Function 51 FR_SEL Output free running in the video signal no input 52 RGB_SEL Input switch of INPUT1 (Dsub15) / INPUT2 (BNC) 53 POWER POWER ON/OFF output 54 BUSY Busy input from the microcomputer 55 BUSY30...
Page 145 PDP-433CMX, PDP-433MXE HD64F2328VF (RGB ASSY : IC5601) • Wide Microcomputer • Pin Function Pin Name Function Non connection Not used Non connection 3.3V power supply Address bus 0 with each IC Address bus Address bus UA10 UA11 UA12 UA13 Address bus...
Page 146 PDP-433CMX, PDP-433MXE Pin Name Function Data bus UD10 UD11 UD12 UD13 Data bus UD14 UD15 3.3V power supply D_TXD Communication data output to the main unit microcomputer EXT_TXD 232C communication output to the external personal computer (FLASH2) D_RXD Communication data input from the main unit microcomputer...
Page 147 PDP-433CMX, PDP-433MXE Pin Name Function Reading of external address space HWRB Upper rank data (D15 to D8) writing of external address space PLL_CE Chip enable signal output for AD/PLL WAIT_IP WAIT input for IC102 Non connection TXD_WU Communication data output (AD/PLL)
Page 148 PDP-433CMX, PDP-433MXE HD64F2328VF (DIGITAL VIDEO ASSY : IC1101) • Panel Microcomputer • Pin Function t i s...
Page 149 PDP-433CMX, PDP-433MXE . ) r . ) r . ) r l l i d l i l l i d l i...
Page 150 PDP-433CMX, PDP-433MXE c i f...
Page 151 PDP-433CMX, PDP-433MXE GAL22V10 (X DRIVE ASSY : IC2006) • Drive Protect PLD • Pin Assignment (Top View) I/CLK I/O/Q I/O/Q I/O/Q I/O/Q I/O/Q I/O/Q I/O/Q I/O/Q I/O/Q I/O/Q • Block Diagram XSUS_BI 1_50 XSUS_BO 1_24 1_40 XSUS_UI 1_49 XSUS_UO 1_23...
Page 152 PDP-433CMX, PDP-433MXE GAL22V10 (Y DRIVE ASSY : IC3003) • Drive Protect PLD • Pin Assignment (Top View) I/CLK I/O/Q I/O/Q I/O/Q I/O/Q I/O/Q I/O/Q I/O/Q I/O/Q I/O/Q I/O/Q • Block Diagram sus_mute_in 1_64 1_63 ysusbin ysusbout 1_39 1_62 1_20 ysusuin...
Page 153 PDP-433CMX, PDP-433MXE M30624FGAFP (DIGITAL VIDEO ASSY : IC1207) • Module Microcomputer • Pin Function l a i n i l l a i n i l n i l , y l l l u l l u t i s...
Page 154 PDP-433CMX, PDP-433MXE a l l g i l g i l t s i l a i n i l...
Page 155 PDP-433CMX, PDP-433MXE PD6358A (DIGITAL VIDEO ASSY : IC1301) • Picture Improved IC • Pin Function ) t r ) t i...
Page 156 PDP-433CMX, PDP-433MXE ) t r ) t i ) t i ) t i ) t i ) t i f i f ) t i ) t i ) t i ) t i ) t i ) t i...
Page 157 PDP-433CMX, PDP-433MXE ) t r ) t i...
Page 158 PDP-433CMX, PDP-433MXE ) t r ) t i f i f ) t i ) t i r i f ) t i ) t i ) t i r i f ) t i ) t i f i f...
Page 159 PDP-433CMX, PDP-433MXE ) t i r i f ) t i ) t r...
Page 160 PDP-433CMX, PDP-433MXE ) t i ) t i ) t i ) t i ) t i ) t i ) t i r i f ) t i ) t i ) t i ) t i ) t i...
Page 161 PDP-433CMX, PDP-433MXE ) t i ) t i ) t i ) t i ) t i ) t i ) t i...
Page 162 PDP-433CMX, PDP-433MXE PST9246N (DIGITAL VIDEO ASSY : IC1208) • Reset IC • Pin Assignment (Top View) SOT - 25 (TOP VIEW) • Block Diagram • Pin Function Pin No. Pin name Functions control pin Substrate pin GND pin Reset signal output pin...
Page 163 PDP-433CMX, PDP-433MXE FS781BZB (DIGITAL VIDEO ASSY : IC1802) • Low EMI Clock IC • Pin Assignment (Top View) Xout FS78x FSOUT 8 Pin SOIC Package • Block Diagram Loop Filter 4(6) 250 K Reference 1(3) Divider Phase 8 pF Detector 10 pF.
Page 164 PDP-433CMX, PDP-433MXE ML6426CS-1 (RGB ASSY : IC4403) • LPF IC • Pin Assignment (Top View) A/B MUX SYNC IN R IN A/Y IN A DISABLE GNDO V CC R OUT /Y OUT R IN B/Y IN B V CCO G IN A/U IN A...
Page 165 PDP-433CMX, PDP-433MXE CXA3516R (RGB ASSY : IC4603) • AD + PLL IC • Pin Assignment (Top View)
Page 166 PDP-433CMX, PDP-433MXE • Block Diagram...
Page 167 PDP-433CMX, PDP-433MXE • Pin Function...
Page 168 PDP-433CMX, PDP-433MXE...
Page 169 PDP-433CMX, PDP-433MXE...
Page 170 PDP-433CMX, PDP-433MXE BA5417 (MX AUDIO ASSY : IC8601) • Power Amp. • Block Diagram T . S . D S T . B Y F I L T E R • Pin Function...
Page 171 PDP-433CMX, PDP-433MXE STK795-460 (X DRIVE ASSY : IC3200, IC3201) (Y DRIVE ASSY : IC2206, IC2214) • PDP Pulse Module IC • Block Diagram...
Page 172: Panel Facilities
PDP-433CMX, PDP-433MXE 8. PANEL FACILITIES AND SPECIFICATIONS 8.1 PANEL FACILITIES MAIN UNIT Operation panel on the main unit Main unit Note When optional speakers have been connected, the operation panel on the main unit will not be operable. Main unit...
Page 173 For connection of components that have RGB or CONTROL IN/OUT (monaural mini jacks) component output jacks such as a personal computer, For connection of PIONEER components that bear the Î mark. Making CONTROL connection enables control DVD player, or external RGB decoder. Make sure that the connection made corresponds to the format of the of the plasma display as a component in a system.
Page 174 PDP-433CMX, PDP-433MXE AUDIO INPUT (Stereo mini jack) Use to obtain sound when INPUT1, INPUT2 or INPUT5 is selected. Connect this jack to the audio output connector of the device connected to the plasma display’s INPUT1 or INPUT2, or to the audio output connector of the device connected to the video card’s INPUT5.
Page 175 PDP-433CMX, PDP-433MXE REMOTE CONTROL UNIT SCREEN SIZE button Press to select the screen size. INPUT buttons Use to select the input. MENU button Press to open and close the on-screen menu. ADJUST (5/∞/3/2) buttons Use to navigate menu screens and to adjust various settings on the unit.
Page 176 PDP-433CMX, PDP-433MXE INSTALLATION OF THE UNIT Installation using the supplied display stand 3 Fix this unit using the supplied washer and bolt. Be sure to fix the supplied stand to the installation surface. Use commercially available M8 bolts that are 25 mm longer than the thickness of the installation surface.
Page 177 ÷ When possible, please install using parts and accessories on a flat, unwarped surface. manufactured by PIONEER. PIONEER will not he held responsible for accident or damage caused by the use of parts and accessories manufactured by other companies.

This manual is also suitable for:

Pdp-433cmx

Pioneer PDP-433MXE Service Manual

1 Specifications

2 Exploded Views and Parts List

3 Block Diagram and Schematic Diagram

4 PCB CONNECTION DIAGRAM Refer to ARP3124

5 Pcb Parts List

6 Adjustment

7 General Information

8 Panel Facilities

Quick Links

Summary of Contents for Pioneer PDP-433MXE

Page 6: Table Of Contents

Page 7: Specifications

Page 8: Exploded Views And Parts List

Page 32: Block Diagram And Schematic Diagram

Page 54: Pcb Parts List

Page 68: Adjustment

Page 125: General Information

Page 126: Shut Down/Power Down Diagnosis By Led Display

Page 135: Automatic Backup Of Digital Video Assy Data

Page 137: Disassembly

Page 141: Ic Information

Page 172: Panel Facilities

This manual is also suitable for:

Pioneer PDP-433MXE Service Manual

1 Specifications

2 Exploded Views and Parts List

3 Block Diagram and Schematic Diagram

4 PCB CONNECTION DIAGRAM Refer to ARP3124

5 Pcb Parts List

6 Adjustment

7 General Information

8 Panel Facilities

Quick Links

Related Manuals for Pioneer PDP-433MXE

Summary of Contents for Pioneer PDP-433MXE

This manual is also suitable for:

Table of Contents