Download  Print this page

Pioneer PDP 433CMX Operating Instructions Manual

Pioneer pdp-503cmx, pdp-433cmx plasma display cran plasma operating instructions.
Hide thumbs

Advertisement

Plasma Display

Écran à plasma
プラズマディスプレイ
PDP-503CMX
PDP-433CMX
Operating Instructions
Mode d'emploi
高調波ガイドライン適合品
Contents related to system specifications, power requirements,
accessories, and other information differ with respect to the
country where this unit is purchased. For customers living in the
U.S.A. or Canada, please use and refer to the instructions written
in either English or French. For customers in Japan, please use
and refer to the instructions written in Japanese.
Les caractéristiques, les spécifications d'alimentation, les
accessoires et d'autres informations diffèrent d'un pays à
l'autre. Si vous vivez au Canada ou aux États-Unis, reportez-
vous aux instructions en français ou en anglais. Si vous vivez
au Japon, reportez-vous aux instructions en japonais.
電源、付属品等の差異がありますので、日本国内でご購入・ご使
用の際は、本書の日本語ページをご覧下さい。その他の国、地
域でご購入・ご使用の際は、英語またはフランス語ページをご覧
下さい。
「据付工事」 について
本機は十分な技術・技能を有する専門業者が据え付け
を行うことを前提に販売されているものです。据え付
け・取付けは必ず工事専門業者または販売店にご依頼
ください。
なお、据え付け・取り付けの不備、誤使用、改造、天
災などによる事故損傷については、弊社は一切責任を
負いません。
販売店様へ
この取扱説明書は据付け終了後お客様に必ずお渡しし
て、取扱い方法の説明を行ってください。

Advertisement

Table of Contents

   Related Manuals for Pioneer PDP 433CMX

   Summary of Contents for Pioneer PDP 433CMX

  • Page 1: Plasma Display

    Plasma Display Écran à plasma プラズマディスプレイ PDP-503CMX PDP-433CMX Operating Instructions Mode d’emploi 高調波ガイドライン適合品 Contents related to system specifications, power requirements, accessories, and other information differ with respect to the country where this unit is purchased. For customers living in the U.S.A.
  • Page 2 English This unit has been designed for use as a computer display monitor. The optional video card is required if you wish to view other video signals on the monitor. For details consult your local retail dealer. Français Cet appareil est conçu pour une utilisation comme moniteur d’affichage d’ordinateur.
  • Page 3: Operating Instructions

    Operating Instructions Thank you very much for purchasing this PIONEER product. Before using your Plasma Display, please read the “Safety Precautions” and these “Operating Instructions” carefully so you will know how to operate the Plasma Display properly. Keep this manual in a safe place. You will find it useful in the future.
  • Page 4: Safety Precautions

    Safety Precautions IMPORTANT NOTICE The serial number for this equipment is located on the rear panel. Please write this serial number on your enclosed warranty card and keep it in a secure area. This is for your security. CAUTION: WHEN POSITIONING THIS EQUIPMENT ENSURE THAT THE MAINS PLUG AND SOCKET IS EASILY ACCESSIBLE.
  • Page 5: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS READ INSTRUCTIONS — All the safety and operating instructions should be read before the product is operated. RETAIN INSTRUCTIONS — The safety and operating instructions should be retained for future reference. HEED WARNINGS — All warnings on the product and in the operating instructions should be adhered to.
  • Page 6: Declaration Of Conformity

    Address: P.O. BOX 1760, LONG BEACH, CA., 90801-1760 U.S.A. Phone: (800)421-1625 URL: http://Pioneerelectronics.com Please do not ship your product to Pioneer without first calling the Customer Support Division at the above listed number for assistance. Pioneer Electronics (USA) Inc. Customer Support Division P.
  • Page 7: Table Of Contents

    Contents Safety Precautions ... i Features ... 2 Before Proceeding ... 3 How to Use This Manual ... 3 Checking Supplied Accessories ... 5 Part Names and Functions ... 6 Main Unit ... 6 Remote Control Unit ... 7 Connection Panel ... 8 Installation and Connections ...
  • Page 8: Features

    While equipped with a high-precision (1280x768) panel, this unit achieves the highest energy-saving of any display in its class (50- inch XGA class: 380 W; 20% less than previous Pioneer products). In addition, when the Power Control function is selected, power consumption is reduced by 20% compared to the normal operating mode (MODE 1, with color-bar signal input).
  • Page 9: Before Proceeding

    Before Proceeding How to Use This Manual This manual is set up to follow the course of actions and operations in the order that would seem most logical for someone setting up this unit. Once the unit has been taken out of the box and it has been confirmed that all the parts have been received, it may be beneficial to look over the section “Part Names and Functions”...
  • Page 10 Before Proceeding About operations in this manual Operations in this manual are outlined in step by step numbered procedures. Most of the procedures are written in reference to the remote control unit unless the button or control is only present on the main unit. However, if a button or control on the main unit has the same or similar name as that on the remote control unit, that button can be used when performing operations.
  • Page 11: Checking Supplied Accessories

    Checking Supplied Accessories Check that the following accessories were supplied. Power cord Remote control unit AA (R6) batteries (x 2) Cleaning cloth (for wiping front panel) Speed clamps (x 2) Bead bands (x 2) Before Proceeding Display stands (x 2) Washers (x 2) Hex hole bolts (x 2) Remote control unit holder...
  • Page 12: Part Names And Functions

    Part Names and Functions Main Unit Main unit Main unit Display stand Remote control sensor Point the remote control toward the remote sensor to operate the unit (page 8). STANDBY/ON indicator This indicator is red during standby mode, and turns to green when the unit is in the operation mode (page 19).
  • Page 13: Remote Control Unit

    Remote Control Unit When handling the remote control unit ¶ Do not drop or shake the remote control. ¶ Do not use the remote control unit in a location subject to direct sunlight, heat radiation from a heater, or in a place subject to excessive humidity.
  • Page 14: Connection Panel

    Connect a speaker that has an impedance of 8 -16 (page 14). CONTROL IN/OUT (monaural mini jacks) For connection of PIONEER components that bear the Î mark. Making CONTROL connection enables control of this unit as a component in a system (page 15).
  • Page 15 Illustration depicts PDP-503CMX model. CONTROL SPEAKER – Synchronizing signal impedance selector switch Depending on the connections made at INPUT2, it may be necessary to set this switch to match the output impedance of the connected component’s synchronization signal. When the output impedance of the component’s synchronization signal is below 75 , set this switch to the 75 position (pages 12, 14).
  • Page 16: Installation And Connections

    Installation and Connections Installation of the Unit Installation using the supplied display stand Be sure to fix the supplied stand to the installation surface. Use commercially available M8 bolts that are 25 mm longer than the thickness of the installation surface. 1 Fix the supplied stand to the installation surface at each of the 4 prepared holes using commercially available M8 bolts .
  • Page 17 PIONEER stand or installation bracket (sold separately) ÷ When possible, please install using parts and accessories manufactured by PIONEER. PIONEER will not be held responsible for accident or damage caused by the use of parts and accessories manufactured by other companies.
  • Page 18: Connection To Input1 And Input2

    Installation and Connections Connection to INPUT1 and INPUT2 The INPUT 1 and INPUT 2 jacks are used to connect the display to a computer. After making the connections, adjust the screen settings in accordance with the computer’s signal output. See pages 17-18 for information regarding settings.
  • Page 19 When connecting to INPUT1 INPUT1 OUTPUT ANALOG RGB (ANALOG RGB) Connect the cable corresponding to the shape of the input terminal on this unit and the personal computer’s output terminal. Secure by tightening the terminal screws on both units. After connecting, on-screen setup is necessary. Please see pages 17 and 18.
  • Page 20: Audio Connections

    Installation and Connections Connection of composite SYNC analog RGB source Make composite SYNC connections for a personal computer with output that has the vertical synchronization signal layered on top of the horizontal synchronization signal. When connecting to INPUT1 INPUT1 OUTPUT ANALOG RGB (ANALOG RGB) On-screen setup is necessary after connection.
  • Page 21: Control Cord Connection

    Control Cord Connection When control cord connections are made, remote control operation of connected PIONEER components that bear the Î logo mark is done through the remote sensor on this unit. When the connection is made to the CONTROL IN jack on another unit, the remote sensor of that component will no longer receive signals.
  • Page 22: How To Route Cables

    Installation and Connections How to Route Cables Speed clamps and bead bands are included with this unit for bunching cables together. Once components are connected, follow the following steps to route cables. Organize cables together using the provided speed clamps. Insert 1 into an appropriate hole on the rear of the unit, then snap 2 into the back of 1 to fix the clamp.
  • Page 23: Setting Up The System

    Setting Up the System Setup after Connection After components have been connected to INPUT1 or INPUT2, on-screen setup is necessary. Follow the procedure described below and make settings as they apply to the type of components connected. Screen Mode setup Note These settings are required only when using the following input signal refresh rates: 1 31.5 kHz horizontal / 60 Hz vertical;...
  • Page 24 Setting Up the System CLAMP POSITION setup Depending on the signal, analog RGB signals may result in the screen image appearing with a whitish or greenish cast. In such cases, set “CLAMP POSITION” to LOCKED. ÷ Normally, leave this setting at AUTO. Setup of CLAMP POSITION Press MENU to display the menu screen.
  • Page 25: Operations

    Operations Selecting an Input Source This section explains the basic operation of this unit. Outlined on the following pages is how to turn the main power on and off, put this unit in the operation or standby mode and how to select connected components. Before you begin, make sure you have: •...
  • Page 26: To Adjust The Volume

    Operations To adjust the volume VOLUME +/– Press VOLUME on the remote control unit. Use VOLUME + or VOLUME – to adjust the volume of the connected speakers. V O L U ME To mute the sound MUTING Press MUTING on the remote control unit. Press MUTING again to restore the sound.
  • Page 27: Screen Size Selection

    Screen Size Selection This unit incorporates screen modes of various height and width ratios. For optimal viewing, we recommend that you select the screen mode that best matches the video source that you are viewing. Although these modes are designed for full display of a picture on a wide screen, it is our hope that you make use of them with a full understanding of the manufacturer’s intentions.
  • Page 28 Operations 4 PARTIAL (*Supported only on PDP-503CMX) The PARTIAL setting is available only during personal computer input (1280 x 1024/60 Hz only). The input signal and the screen maintain a dot to line ratio of 1:1. Display is highly faithful to the source. However, in order to maintain the 1:1 ratio, a portion of the display will not appear on the screen.
  • Page 29: Partial Image Enlargement (point Zoom)

    Partial Image Enlargement (POINT ZOOM) This display allows any one of nine screen areas (AREA 1 to AREA 9) to be selected and enlarged to x1.5, x2, x3, or x4. When performing point zoom enlargement, the direction buttons (5/∞/2/3) can be used to move the enlarged portion up-down and right-left.
  • Page 30: Automatic Power Off

    Operations Automatic Power OFF This display is equipped with automatic power- management and auto-power-off functions, which allow the unit to automatically switch to power-saving mode when no sync signal is detected. (A warning message appears onscreen before these functions operate.) Notes ÷...
  • Page 31: Display Panel Adjustments

    Display Panel Adjustments Adjusting the Picture Quality Press MENU to display the menu screen. MAIN MENU PICTURE SCREEN SET UP CO NT RA S T I GHT . R L E V E L : 6 0 G L E V E L : 6 0 B L E V E L H E NH AN CE...
  • Page 32: Adjusting The Image Position And Clock (automatic Adjustment)

    Display Panel Adjustments Adjusting the Image Position and Clock (Automatic Adjustment) Pressing AUTO SET UP on either the display or the remote control unit will adjust the screen position and clock to optimum values. Note Perform this adjustment individually for each input function (INPUT 1, INPUT 2), and each signal type.
  • Page 33: Manual Adjustment Of Screen Position And Clock

    Manual Adjustment of Screen Position and Clock Press MENU to display the menu screen. MAIN MENU PICTURE SCREEN SET UP CO NT RA S T I GHT . R L E V E L : 6 0 G L E V E L : 6 0 B L E V E L H E NH AN CE...
  • Page 34: Other Operations

    Other Operations Rewriting the Input Display (INPUT LABEL) This function allows rewriting of the screen contents displayed with differing inputs. For example, the default “INPUT 1” can be changed to “COMPUTER” or other name describing the connected component (up to maximum of 8 characters).
  • Page 35: Power Control Function

    Power Control Function The power control function allows screen brightness to be suppressed as a means of lowering power consumption and reducing display deterioration. Press MENU to display the menu screen. The menu will be displayed. MAIN MENU PICTURE SCREEN SET UP CO NT RA S T I GHT .
  • Page 36: Audio Output (audio Out)

    Other Operations Press SET to select INPUT 1. The factory default setting is OFF. Each time SET is pressed the selector function switches alternately as shown: 3 OFF INPUT1 2 ÷ When OFF is selected, AUTO FUNCTION is disabled. ÷ When INPUT 1 is selected, the display input automatically switches to INPUT 1 when a signal is detected at the INPUT 1 jack.
  • Page 37: Additional Information

    Immediately turn off power, remove power plug from its outlet, and consult a Pioneer service center or your dealer. been attempted. Check input signals, connections and other settings. for 1-2 minutes, then try turning power on again.
  • Page 38: General Problems

    Additional Information General problems Problem • No power • Is the power cord disconnected? (page 15) • Has the MAIN POWER switch been switched on? (page 9) • Unit cannot be operated. • External influences such as lightning, static electricity, etc., may cause improper operation. In this case, operate the unit after first turning the MAIN POWER on/off, or unplugging the power cord and re-plugging it in after 1 to 2 minutes.
  • Page 39 Although this unit incorporates high precision technology in its design, please understand that there may be extremely slight pixel breakup, or light emission fault. Note In order to protect the panel and internal circuitry, this display is provided with a cooling fan designed to turn on/off and change speed automatically in accordance with ambient temperature conditions (the fan sound will change in accordance with its speed).
  • Page 40: Specifications

    Additional Information Specifications General (PDP-503CMX) Light emission panel ... 50 inch plasma display panel Number of pixels ... 1280 x 768 Power supply ... AC 100 - 120 V, 50/60 Hz Rated current ... 3.8 A - 3.1 A Standby power consumption ... 1 W External dimensions ...
  • Page 41: Supplement 1

    Supplement 1 -1/2: PDP-503CMX PC signal compatibilty table (INPUT1, INPUT2) Refresh rate Resolution (Dot x Line) Vertical Horizontal 56.4Hz 24.8kHz 640x400 70.1Hz 31.5kHz 31.5kHz 60Hz 640x480 35.0kHz 66.7Hz 37.9kHz 72.8Hz 37.5kHz 75Hz 43.3kHz 85Hz 35.2kHz 800 x600 56Hz 37.9kHz 60Hz 48.1kHz 72Hz 46.9kHz...
  • Page 42: Supplement 2

    Additional Information Supplement 1 -2/2: PDP-433CMX PC signal compatibilty table (INPUT1, INPUT2) Refresh rate Resolution (Dot x Line) Vertical Horizontal 56.4Hz 24.8kHz 640x400 31.5kHz 70.1Hz 31.5kHz 60Hz 640x480 35.0kHz 66.7Hz 37.9kHz 72.8Hz 37.5kHz 75Hz 43.3kHz 85Hz 35.2kHz 800 x600 56Hz 37.9kHz 60Hz 48.1kHz...
  • Page 43: Explanation Of Terms

    Supplement 2 Signal assignment of INPUT 1 (Mini D-sub 15 pin socket connector) 15 11 Pin No. Input R or C G or Y B or C NC (No connection) DDC + 5V NC (No connection) NC (No connection) DDC SDA NC (No connection) HD or H/V SYNC DDC SCL...
  • Page 44 Published by Pioneer Corporation. Copyright © 2002 Pioneer Corporation. All rights reserved.

This manual is also suitable for:

Pdp-503cmx

Comments to this Manuals

Symbols: 0
Latest comments: