Safety Precautions; Specifications; Identification Of Parts; Before Installation - Toto TLP02309 Installation Manual

03N51E
Appearance of the Wall-Mounted Single Handle Faucet (Embedded Type)
Install the product according to this Installation Manual so that the product fulfills its function. When the installation is over, fully explain how to use the single handle faucet to the customer.

Safety Precautions

Please read these Safety Precautions before installation work in order to install the product properly.
●This manual employs various indications in order to install
the product properly and to prevent harm to the customer
and other people, as well as damage to their properties.
The indications and meanings are as follows:
This indication means that if
the content in the column of
WARNING
this indication is ignored or
handled wrongly, death or
serious injury may occur.
This indication means that if
the content in the column of
CAUTION
this indication is ignored or
handled wrongly, injury or
property damage may occur.
Do not use supply water at a temperature higher than 90°C.
If you use the water at a temperature higher than 90°C, the water may scald
you and the life of the faucet may shorten causing it to break and leak water
that may wet household articles and cause damage to your property.
Prohibited
Do not mount the product on glass, mirrors, etc.
Otherwise, the glass, mirror, etc. may break and injure you, and water
may leak, wet household articles and cause damage to your property.
Do not disassemble or remodel the product with other
items than what are described in this manual.
Otherwise, the water may scald or injure you and the product may break and
Disassembly
leak water that may wet household articles and cause damage to your property.
Prohibited

Specifications

Minimum water pressure
Cold / Hot
Maximum water pressure
water supply
pressure
Recommended
water pressure
Temperature water supply
Environmental temperature used
Application
Water discharge volume

Before Installation

●In order to prevent scalding due to erroneous operation, be sure to set the
cold water supply pressure higher than the hot water supply pressure or
set them to the same pressure. Even when applying pressure to the hot
water side, be sure to set the hot water supply pressure side lower than
the cold water side.
●In the case of an instantaneous hot-water heater, the water heater may
not ignite according to the conditions such as performance and water
pressure of the water heater.
●Since the flow is examined before packaging the product, some water may
remain in the product, but nothing is wrong with the product.
Installation Manual
(Be sure to follow all precautions for safety sake.)
●The contents you must observe are
classified into the following symbols;
their meanings are explained.
Indicates things that you
must not do as "Prohibited".
The left figure indicates that
"Disassembly is Prohibited".
Indicates things that you
must do without fail as
"Mandatory".
The left figure indicates to
"Execute it without fail".
WARNING
0.05 MPa (Dynamic)
1.0 MPa (Static)
0.1~0.5 MPa (Dynamic)
4~90°C. Recommended
hot water temperature 60°C
1~40°C
For restroom in general house
5.0 L/min. constant
flow valve incorporated
Do not subject the product to strong force or impact.
Otherwise, the product may break and leak water that may wet
household articles and cause damage to your property.
Do not use the product in any place where freezing can
Prohibited
be expected.
Otherwise, parts may break and leak water that may wet household
articles and cause damage to your property.
Using appropriate embedment setscrews, be sure to
mount the product on a wall or building member that has
an enough strength to bear the product.
If the embedded part is anchored in walls that do not have enough
strength, such as clay walls, chalk walls, etc., the spout and the
handle may come off or the wall may break and injure you, and water
may leak, wet household articles and cause damage to your property.
Mandatory
The clearance between the plastic cover of the embedded
part and the wall should be assuredly waterproofed with
waterproof sheet and silicone.
Water may leak, wet household articles and cause damage to your
property.

Identification of Parts

Identify the following parts.
O-ring
Spout
Accessories
Joint Spring
Setscrew setscrew washer
(x 3) (x 2) (x 2)
Necessary parts (Procured in the field)
1
TLP02309
TLP02310
CAUTION
Appearance
Handle member Joint
operating section
Others
Hand it over to the customer without fail.
Hexagonal wrench
Installation
Operation (Distance across faces:
Manual
Manual 2.5 mm, 2 mm)
Silicone
Continued on the back cover
2017.8
Water drain