Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ElectrIQ eiQODGRSS
Summary of Contents for ElectrIQ eiQODGRSS
- Page 1 USER MANUAL GAS PATIO HEATER eiQODGRSS STAINLESS STEEL eiQODGRBL BLACK eiQODGRWH WHITE eiQODGAG GREY 0063-21 WARNING: FOR OUTDOOR USE IN WELL VENTILATED AREAS ONLY. DO NOT USE INDOORS. PLEASE KEEP THE MANUAL FOR FUTURE REFERENCE...
-
Page 2: Table Of Contents
CONTENTS SAFETY PARTS LIST ASSEMBLY OPERATION LEAK TESTING GAS INFORMATION MAINTENANCE STORAGE TROUBLESHOOTING TECHNICAL SPECIFICATIONS SUPPORT... -
Page 3: Safety
IMPORTANT SAFETY INFORMATION Please read this user manual before using this heater and keep it safe for future reference. Read the following instructions carefully and be sure your patio heater is properly ⚫ installed, assembled and cared for. Retain the instructions for future reference. Failure to follow these instructions may result in serious bodily injury and/or ⚫... - Page 4 For use outdoors or in well ventilated areas. • A well-ventilated area must have a minimum of 25% of the surface area open. • The surface area is the sum of the walls surface. • The use of this appliance in enclosed areas dangerous PROHIBITED.
-
Page 5: Parts List
PRODUCT OVERVIEW AND PART LIST... - Page 6 PART PART PICTURE PICTURE NAME NAME Reflector Dome Right Panel Reflector Emitter Screen Wheel Assy Mesh Support Base weight Mesh plate Control Glass Dial Tube Cylinder fastener Spiral Fixing PART PART Glass NAME Base M4 x 10 Burner M4 x 10 Assy M5 x 12 Left...
-
Page 7: Assembly
ASSEMBLY Required Tools: Philips Screwdriver / Adjustable Spanners / Wrenches Leak Detection Solution: One-part detergent and three parts water Before assembly, ensure all packing material and any transit protection is removed. Step 1 Parts required: Mesh Support Rod x 3 Mesh x 3 12 x CC M5x12 screws Connect the three Mesh Support Rods to the three Mesh Panels using 12 x M5x12 screws... - Page 8 Step 3 Parts required: 3 x AA M4x10 Screws Attach the Relector to the Mesh Assembly using M4x10 screws Step 4 Parts required: 1 x 1 Reflector Dome 3 x EE Washers 3 x FF M6 Dome Nuts Attach the Reflector Dome to the pillars on the Reflector using the Washers and Dome Nuts...
- Page 9 Step 5 Parts required: 2 x II M6x20 Bolts 1 x Base 1 x Wheel Assembly Attach the Wheel Assembly to the Base using the 2 x M6x20 Screws Step 6 Parts required: Base weight plate 4X JJ M4X10 screws Screw the weight plate onto the base assembly...
- Page 10 Step 7 Parts required: Left Panel Right Panel 6 x CC M5x12 screws Attach the Left and Right Panels to the Base using 6 M5x12 screws Step 8 Parts required: Door Panel 4 x BB M4x10 screws 4 x DD M4 nuts Attach the Door Panel by fitting nuts and screws to the hinges on the Door Panel and Right Panel...
- Page 11 Step 9 Cylinder Fastner x1 Unscrew the locking nut on the main body as shown. Then place the cyclinder fastner inside the main body and esnure that it fits securley onto the inside of the body. Through the hole shown above, feed the inbuilt screw through and re attach the locking nut to secure the cyclinder fastner.
- Page 12 Step 11 Parts required: 2 x BB M4x10 Screws 4 x CC M5x12 Screws Spiral Fixing Glass Base Add the Spiral using M4x10 screws, then the Fixing Glass Base with M5x12 screws Step 12 Parts required: Glass Tube Insert the Glass Tube onto the Burner Assembly...
- Page 13 Step 13 Parts required: 3 x HH M5x16 Screws Slide the Mesh Assembly over the Glass Tube and fasten in place with the three M5x16 screws Step 14 Parts required: Battery (not included) Open the Panel Door, remove the control dial and insert one AA battery...
- Page 14 Step 15 GAS CONNECTION Parts required: Cylinder (not included) Attach the gas line to the cylinder valve and ensure the connection is secure. Step 16 Parts required: None Your Patio Heater is now ready...
-
Page 15: Operation
OPERATING INSTRUCTIONS BEFORE FIRST USE AND AFTER EVERY GAS CYLINDER CHANGE, GAS DELIVERY SYSTEM MUST BE PURGED OF AIR BEFORE IGNITING! TO DO THIS, TURN THE CONTROL DIAL ANTI-CLOCKWISE TO THE PILOT SETTING. PRESS THE DIAL IN AND HOLD FOR 1 MINUTE BEFORE ATTEMPTING IGNITION. BATTERY REPLACMENT Remove the control dial. -
Page 16: Leak Testing
LEAK TESTING NEVER USE A NAKED FLAME TO CHECK FOR LEAKS. NEVER LEAK TEST WHILE SMOKING. The gas connections on this appliance are leak tested at the factory prior to shipment. This appliance needs to be periodically checked for leaks and an immediate check is required if the smell of gas is detected. -
Page 17: Maintenance
MAINTENANCE To enjoy years of outstanding performance from your heater, make sure you perform the following maintenance activities on a regular basis: • Keep exterior surfaces clean. • Use warm soapy water for cleaning. Never use flammable or corrosive cleaning agents. •... -
Page 18: Troubleshooting
TROUBLESHOOTING PROBLEM CONDITION Cylinder valve is closed Open valve Blockage in orifice or pilot tube Clean or replace orifice or pilot tube Open gas line and bleed it (pressing Air in the gas line control dial in) for not more than 1- Pilot won’t light 2 minutes or until you smell gas Low gas pressure... -
Page 19: Technical Specifications
TECHNICAL SPECIFICATIONS Model: eiQODGRSS eiQODGRBL eiQODGRWH eiQODGAG Model Identifier: SRPH84 Nominal Heat input =6.0kW Consumption: 800 g/h(G30) - 786g/h(G31) BG-CZ-DK- BE-CH-CY- EE-FI-FR- CZ-ES-FR- HR-HU-IS- AT-CH-DE- Country Code GB-GR- IE- IT-LT-LU- IT-LT-LU-LV- MT-NL-NO- PT-SK-SI RO-SE-SI- SK-TR Gas Category 3+(28-30/37) 3B/P(30) 3B/P(50)
Need help?
Do you have a question about the eiQODGRSS and is the answer not in the manual?
Questions and answers