Subscribe to Our Youtube Channel
Related Manuals for ElectrIQ EQODHMBR
Summary of Contents for ElectrIQ EQODHMBR
- Page 1 USER MANUAL GAS PATIO HEATER EQODHMBR EQODHMGR WARNING: FOR OUTDOOR USE ONLY OR IN WELL VENTILATED AREAS PLEASE KEEP THE MANUAL FOR FUTURE REFERENCE...
-
Page 2: Table Of Contents
CONTENTS SAFETY PARTS LIST ASSEMBLY OPERATION LEAK TESTING GAS INFORMATION MAINTENANCE STORAGE TROUBLESHOOTING TECHNICAL SPECIFICATIONS SUPPORT... -
Page 3: Safety
IMPORTANT SAFETY INFORMATION Please read this user manual before using this heater and keep it safe for future reference. Read the following instructions carefully and be sure your patio heater is properly ⚫ installed, assembled and cared for. Retain the instructions for future reference. Failure to follow these instructions may result in serious bodily injury and/or ⚫... -
Page 4: Assembly
For use outdoors or in well ventilated areas. • A well-ventilated area must have a minimum of 25% of the surface area open. • The surface area is the sum of the walls surface. • The use of this appliance in enclosed areas can be dangerous and is PROHIBITED. -
Page 5: Parts List
PRODUCT OVERVIEW PART DESCRIPTION QUANTITY Reflector Panel Reflector Plate Burner head Assembly Deck Ring Wicker table Wicker tank housing assembly Post Wheel kits... - Page 6 PATIO HEATER ASSEMBLY Required Tools: Philip Screwdriver / Adjustable Spanners / Wrenches Leak Detection Solution: one-part detergent and three parts water Assemble all nuts and bolts loosely at first. Tighten all connections after completion of assembly. This eases your work and increases the stability of your appliance.
- Page 7 4. Attach the reflector panels (A) together using M6 x 8mm screws (FF), Φ6 washers (DD) and cap nuts (GG). Secure loosely with cap nuts (GG). Note: In order to achieve proper alignment of reflector sections, it may be necessary to loosen the preassembled bolts prior to assembly and retighten once complete.
- Page 8 7. Connect hose & regulator to gas pipe (I). Insert gas pipe with hose & regulator assembly (I/J) through top of the housing (F) and Post (G), tighten gas pipe (I) to head assembly(C). Secure the head assembly (C) to the post (G) using preassembled bolts M5 x 10 (HH), lock washer (JJ), and Φ5 washers (EE).
-
Page 9: Operation
OPERATING INSTRUCTIONS BEFORE FIRST USE AND AFTER EVERY GAS CYLINDER CHANGE, GAS DELIVERY SYSTEM MUST BE PURGED OF AIR BEFORE IGNITING! TO DO THIS, TURN THE CONTROL DIAL ANTI-CLOCKWISE TO THE PILOT SETTING. PRESS THE DIAL IN AND HOLD FOR 1 MINUTE BEFORE ATTEMPTING IGNITION. BATTERY REPLACMENT Remove the ignition cap from the BURNER ASSEMBLY (J) by turning cap counterclockwise. -
Page 10: Leak Testing
LEAK TESTING NEVER USE A NAKED FLAME TO CHECK FOR LEAKS. NEVER LEAK TEST WHILE SMOKING. The gas connections on this appliance are leak tested at the factory prior to shipment. This appliance needs to be periodically checked for leaks and an immediate check is required if the smell of gas is detected. -
Page 11: Maintenance
MAINTENANCE To enjoy years of outstanding performance from your heater, make sure you perform the following maintenance activities on a regular basis: • Keep exterior surfaces clean. • Use warm soapy water for cleaning. Never use flammable or corrosive cleaning agents. •... -
Page 12: Troubleshooting
TROUBLESHOOTING PROBLEM CONDITION Cylinder valve is closed Open valve Blockage in orifice or pilot tube Clean or replace orifice or pilot tube Open gas line and bleed it (pressing Air in the gas line control dial in) for not more than 1- Pilot won’t light 2 minutes or until you smell gas Low gas pressure... -
Page 13: Technical Specifications
The appliance shall only be installed or operated with maximum height from the rim of reflector to the ground, so the adjustable device shall be fixed according to this requirement. Close the valve of the gas cylinder or the regulator after use. electriQ UK SUPPORT www.electriQ.co.uk/support...
Need help?
Do you have a question about the EQODHMBR and is the answer not in the manual?
Questions and answers