Download Print this page
Siruba F007KD Parameter Manual

Siruba F007KD Parameter Manual

Electronic control parameter manual
Hide thumbs Also See for F007KD:

Advertisement

Available languages

Available languages

Quick Links

電控參數說明書
ELECTRONIC CONTROL PARAMETER MANUAL
F007KD

Advertisement

loading

Summary of Contents for Siruba F007KD

  • Page 1 電控參數說明書 ELECTRONIC CONTROL PARAMETER MANUAL F007KD...
  • Page 2 歡迎使用本公司產品,制衣行的正確投資選擇! Welcome to use the our products, it is the right investment choices in garment industry! 本說明書為本公司新研發的“節能 2 路 24V 直驅控制箱”產品參考手冊,請認真閱讀此手冊 以更好運用本公司產品。 This manual is a new product reference manual of the company's "Energy Saving 2 way 24V Direct Drive Control Box". Please read this manual carefully to make better use of our products. 一、安全說明:General SafetyInstructions 1:電機電控接通電源時(開機狀態)請不要把腳放在腳踏板上...
  • Page 3: Table Of Contents

    目錄 Content 一、產品介紹 Product instructions 二、安裝調試 Installation and trial-run 三、控制台使用說明 Control panel Instruction 四、一般故障處理 Common faults and treatment 五、作業環境要求 Environmental Requirements 六、保修服務 Warranty service...
  • Page 4: Product Instructions

    一、產品介紹: Product instruction 本產品由本公司自主研發,產品個性鮮明,真正體現出了機電一體化 的概念,更是節能、高效、環保、優美集結於一身。可廣泛適用於多 種縫紉設備。 This product by the company independent research and development, distinct personality, truly reflects the concept of mechanical and electrical integration, more energy saving, high efficiency, environmental protection, beautiful assembled in one. It can be widely applied to a variety of sewing equipment.
  • Page 5 照 明 燈 介 面 6P 多 功 能 (12V)說明表 2 埠如表 1 6P 多功能埠: 表 1 序號 編號 功能 備註 Serial No Number Number remarks 抬壓腳介面 1 為正;4 為負 foot presser 1 is positive pole lifter port 4 is negative pole 吸屑介面...
  • Page 6 ※:抬壓腳介面(24V)和吸屑介面(24V)埠只能使用 24V 電子閥(最大輸出 電流 200mA;如超出可能導致使用故障,嚴重導致控制器損毀。) ※:presser foot lifter(24V) and waste suction port (24V), the port can only use 24V valve (the biggest output current is 200mA; if over this, will occur error, even let the control box broken) B.電機: motor 電機轉子屬於稀土永磁材料,具備功率大,節能環保等各大優點。電機內設有霍...
  • Page 7: Installation And Trial-Run

    2. 220V、110V 性能參數指標:Specifications Specifications 220V 性能參數指標 220V 電源供電電壓 Voltage 220V 單相 1phase 頻率 Frequency 50~60HZ 電機轉速 Speed 200-5000RPM 電機扭矩 Motor torque ≤3.5NM 電機功率 550W 110V 性能參數指標 220V Specifications 電源供電電壓 Voltage 110V 單相 1 phase 頻率 Frequency 50~60HZ 電機轉速 Speed 200-5000RPM 電機扭矩...
  • Page 8 安裝示意圖: 直驅電機 Schematic diagram of the installation of direct drive motor 直驅電機安裝共 6 步驟:Motor installation of a total of 6 steps (1)裝底板:Install Plate a)拆掉縫紉機上的手輪、皮帶、皮帶罩。 Remove the hand wheel, belt cover and wind blade on the sewing machine. b)如安裝圖所示將圖①底板用圖②④螺釘,圖③墊片鎖在對應的縫紉 機孔位上。 According to the above install picture, use the screw(picture ② ④ ) , washer(picture③) installing the plate(picture①) into the sewing machine head.
  • Page 9 (3)裝電機:Install Moter a)如安裝圖所示將圖⑨電機裝入並用圖⑩螺釘鎖緊固定在圖①底板上 (注:電機裝入轉子要注意磁鐵吸力,小心夾到手。) According to the above install picture,use the screw(picture⑩)to fix the motor(picture⑨) in to the plate(picture①).(attention: please take care the magnetism to hurt the hand when put the motor to the rotor.) (4)檢查轉子和定子是否裝好 Check the rotor and the stator is installed or not A)拿出圖⑨上的橡膠孔塞。...
  • Page 10 Adjusted to fit back rubber hole stopper.(Notes: The distance between two flat as small as possible, if more than 1.5mm, motor will be calorific value more and torque decreases.) (5)裝風葉和外殼:Install Fan and the cover 用手轉動縫紉機,使機針停在最高位,縫紉機手輪如圖 B Use hand to turn the sewing machine head, let the needle stop in the highest position 如安裝圖所示將圖⑩風葉裝入並用圖⑪上的螺釘鎖緊,(注:...
  • Page 11 (6)檢查:手轉動手輪無卡擦現象,縫紉機也無加重。 Check: Hand wheel hand wheel without card wiping phenomenon, Sewing machine weight does not increase 三、控制台使用說明: Installation for Control Panel 各按鍵的用途:Each key purpose (1)“P”鍵的用途: Function of “P” key: 第一:“P”鍵為上、下停針鍵,按下“P”鍵,上燈孔亮,為上停針;下燈 孔亮,為下停針;兩個燈孔都不亮,為自由停針; First:”P” key for upperand lower stop needle position. Press “P”,if up pinhole lamp lights means it’s up stop needle, if down pinhole lamp lights means that it is down stop needle , if two lamps off means needle position is freedom.
  • Page 12 2. To enter the parameter method of operation: Example: How to change the motor from clockwise to counterclockwise: Step one: Open the power; Step two: Press the ”P” key, no leave, and press “+” key, the screen will display the P-00; Step third: Press “+”...
  • Page 13 抬壓腳起動時間 P-11 Presser foot ascend 0-2000ms starting time 抬壓腳保護時間 P-12 Ascension presser 1-120s foot protection time 老款平車電機選擇 1 是老款平縫機電機 0 是普通機 Old section flat Motor option 1 is old P-13 0 is ordinary sewing sewing machine section flat sewing machine selection machine 最大電流限制...
  • Page 14 吸氣維持功率 P-27 suction maintain 1-100% power 吸氣釋放時間 P-28 0-500ms 20ms suction release time 吸氣保護時間 吸氣單次動作最長時間 P-29 suction protection 1-120s the longest time of suction time single action 1 為觸發模式:後踏抬壓腳中 立不會自動放壓腳 0 為跟隨模式:後踏抬壓腳、 中立或前踏放壓腳 1 is trigger mode: back step 壓腳觸發模式 0:關閉...
  • Page 15: Common Faults And Treatment

    當電壓高於 395 會報警, (直流母線電壓/1.414=交 顯示直流母線電壓 流母線電壓)when the volt P-40 display DC buses 60-500V 320v is higher than 395V will voltage alarm,(DC buses volt/1.414 = AC buses volt ) 設為 0 關閉過壓報警,設 為 1 打開報警,當直流母 線電壓超過 395V 時,報 警 Er16,電機自動停止運 行,報警後當電壓低於 385v 電機可再次運行...
  • Page 16 1.電機超載 2.電機與電控相連接的四心線接觸不好 堵轉保護 3.電機斷線或壞了 Er04 Locked-rotor 1. The motor overload protection 2. The motor and the controller connected four hole line contact is not good 3. Motor is bad 1.電機超載 硬體過流保護 2.信號線接觸不好或斷了 Hardware 3.主機板壞了 Er05 over-current 1. The motor overload protection 2.
  • Page 17: 五、作業環境要求 Environmental Requirements

    五、作業環境要求:Environmental Requirements 1.請不要在過潮濕環境中作作業 Please do not work at damp place 2.用戶供電應保持穩定 210V-240V (注 : 110V 用戶供電應保持穩定 90V-130V) The voltage requires being stable (210v-240v)(Note: The power supply for 110V users should remain stable at 90V-130V) 3.用戶使用前必須接地,確保人身安全 Must be adequately grounded for safety 4.不要在過熱地方作業...
  • Page 18 由於對產品的改良及更新 , 本產品使用說明書中與零件圖之產品及外觀的修改恕不事先通知 ! The specification and/or the equipment described in the instruction book and parts list are subject to change because of modification with out previous notice F007KD.AUG.2020...

This manual is also suitable for:

F007kd f3x2