Related Manuals for Panasonic NE-1024F
Summary of Contents for Panasonic NE-1024F
- Page 1 Panasonic Operati ng Instructions Commercial Microwave Ovens Model NE-l0547 NE-l0247 Betore operating this oven, please read these instructions completely.
-
Page 2: Table Of Contents
TABLE OF CONTENTS TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE PRECAUTIONS MICROWAVE ENERGY S A F E T Y I N S T R U C T I O N S ...., ..I M P O R T A N T Installation and Grounding Instructions... - Page 3 Your microwave oven is a cooking device and you should use as When using this electric appiiance, basic safety precautions should be lollowed. includrng the following: reduce tne risk ot burns, etectric WARNING-To shock, fire, injury to persons or exposure to excesstve microwave energy: 1.
- Page 4 (120 V). Using a higher voltage is dangerous and may result in a fire or other accident causing oven damage. Using a lower voltage will cause slow heating. Panasonic is NOT responsible for damage resulting from the use of the oven with other than specified voltaqe.
- Page 5 General Use '1 . DO NOT tamper with or make any adjustments or repairs to door, control panel housing, satety interlock switches or any other part of the oven. Do NOT remove outer panel from oven. Repairs should only be done by a qualified service person.
- Page 6 Microwaves are a form of high frequency radio waves similar to those used by a radio including AM; FM and CB. They are, however, much shorter than radio waves; approximately tive inches long. Electricity is converled into microwave energy by the magnetron tube.
- Page 7 Timer Control Panel Door Saiety Lock System 1 . Make sure unit is plugged into a three-prong grounded 120 V circuit. 2. Open the door. PLACE CONTAINER OF FOOD in the oven. 3. CLOSE THE DOOR securely. 4. SET A OESIFIED HEATING TIME. >...
- Page 8 Digital Display Window Indicator Locations A - PBOG lndicator B - DOUBLE OUANTITY (x 2) Heating Indicator C - Memory Pad Number and Heating Time Display (min. sec.) - each indicator 0-9 D - Stage Heating Indicaior - 3 maximum NE-'10547 Control Panel Digital Display Windov, (see below)
- Page 9 Before Operating Vake sure the oven is connected to a properly groundgd electrical outlet. lvren the door is closed, the Display Window is still blank. When the door is opened, the Display Window shows "0". .cr the detail operation, see the page on each feature. This oven is preset at the factory for the following: ' Memory Pads are preset to High Power for the indicated heating times Jor single stage heating.
-
Page 10: Heating
HEATING Open the door and place food in lhe oven cavity. Close the door. "0" must be shor,ving in the Display Window. A. Manual Single Stage Heating: This fealure gives the user maximum llexibility to set the oven to desired heating time and power level. Ideal for menus that require various h€ating requirements. -
Page 11: Programmed Heating
C. Programmed Heating: Example: 1 stage; Memory Pad I to heal tor 3 minutes at HIGH Power 3. Beep tone will sound. Example: 2 stage; Memory Pad 3 (to See page 13 to program Memory Pad. See page l5 to activate Program Lock. ' t . -
Page 12: Programming
Programming - DO NOT OPEN THE DOOR _ The Display Window MUST be blank before programming can begin. lf any indicator light is illuminated in the digital Display Window: Close the door, press STOP/RESET Pad and wait 1 minute until the Display Window goes blank. A. -
Page 13: Programming Memory Pads For 2 Or 3 Stage Heating
NOTE: . Program the remaining Memory Pads as desired by repeating steps 1-5. You may insert up to 10 memory Programs. . When the PROG indicator is blinking, the program can be cancelled and/or the Pad erased by pressing the STOP/RESET Pad. -
Page 14: Programming The Double Quantity Pad For Multiple Portion Heating
C. Programming the Double Quantity Pad - For multiple portion heating: your oven is lactory set to automatically double thg programmed time for multiple portion heating - this is the correct setting tor heating multipleportions of most small foods items. No Iurther programming of the time is necessary for these lood items The time iequired to heat multiple portions ot some large planers and most bulk food loads is slightly less than double that ol a single portion. -
Page 15: Other Features
Other Features A. To Activate Program Lock: This procedure "Locks" the control panel Memory Pads into their programmed heating times and power levels. DO NOT OPEN THE DOOR. The Display Window must be blank before the Program Lock leature can be activated. N O T E : . - Page 16 C. To Read Program List: Allows you to review all currently programmed Pad Number, heating time and power level for each 1. Open the door. , F;;;I I START I NOTE: .lf you want to go to another program, press the Memory Pad you desired to read program, while the information ot lvlemory Pad is being displayed.
- Page 17 D. To Select Beep Tone Options: The Beep Tone can be set. ON or OFF. Open the door. E ''- E. To Read the Cycle Counter: The oven can dispiay the total number of times the oven has been operated cumulatively. Great for analyzing usage of the oven and tratfic flow at the,ocation.
- Page 18 This oven monitors its operation and displays a Failure Code in the Display Window when a problem occurs. Whal to do when a failure code appears: C O D E 'Overcooked lood .Temperature of exhaust air too high. 'Defective sensor circuit F33-34 'When a pad was pressed for more than 30 seconds...
- Page 19 Power Source Required Power Output' Frequency Outer Dimensions ( H x W x D ) Cavity Dimensions ( H x W x D ) Timer 99 min 99 sec (Digital) FRONTVIEW N E - 1 0 5 4 7 120V,60 Hz, single phase 13.44 1 0 0 0 w 2,450 MNZ...
- Page 20 PANASONIC CONSUMER ELECTONIC COMPANY COMPANY DIVISION OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA One Panasonic Way,4A-4, Secaucus, NJ 07094 {€01l 348-5377 TooogopooAp )rinted in Taiwan...