Optimal Use Of The Battery - Panasonic PV-GS36 Operating Instructions Manual

Condensation
If you turn the Camcorder on when condensation
occurs on the head or the tape, Condensation
Indication [ ] is displayed on the Viewfinder or
the LCD Monitor and the messages
[ DEW DETECT] or [
when the tape is inserted) appear. In this case, follow
the procedure below.
1
Remove the tape if it is inserted.
• It takes about 20 seconds to open the Cassette
Holder. This is not a malfunction.
2
Leave the Camcorder with the Cassette
Compartment Cover closed to cool or
warm it to the ambient temperature.
3
Turn the Camcorder on again, set it to
the Tape Recording/Playback Mode and
then check if the condensation indication
disappears.
Especially in cold conditions, dew may be frozen.
In this case, it may take more time before the
condensation indication disappears.
Watch for Condensation even before the
Condensation Indication is displayed.
• The condensation indication may not appear
depending on circumstances. When condensation
occurs on the lens or the Camcorder, it also may
occur on the head and the tape. Do not open the
Cassette Compartment Cover.
When the Lens Is Fogged:
Set the [OFF/ON] Switch to [OFF] and leave the
Camcorder in this condition for about 1 hour. When
the lens temperature becomes close to the ambient
temperature, the fog disappears naturally.
Video Head Clogging and Care
If the heads (the parts that make contact with the
tape) are dirty, mosaic-pattern noise may appear
on the playback image, or the screen as a whole
becomes black. If the heads are extremely dirty,
recording performance deteriorates, and, in the worst
case, the Camcorder cannot record at all.
Causes of Dirty Heads
• Large quantity of dust in the air
• High-temperature and high-humidity environment
• Damaged tape
• Long operating hours
Using Panasonic cleaning cassette
(AY-DVMCLA)
1
Set the Mode Dial to Tape
Playback Mode.
• The One-Touch Navigation icon is
displayed on the lower right of the
screen.
EJECT TAPE] (only
2
Insert the Head Cleaner into the
Camcorder in the same manner as a Video
Cassette.
3
Move the Joystick Control [▲], and
approximately 15 seconds later, move the
Joystick Control [▼]. (Do not rewind the
tape.)
4
Take out the Head Cleaner. Insert a Video
Cassette and start recording. Then, play
the tape back to check the recorded
image.
5
If the image is not still clear, repeat Steps
1 to 4. (Do not use the Head Cleaner 3
times or more consecutively.)
Notes:
• Do not rewind every time you use the Head
Cleaner. Rewind only when the tape reaches the
end, and then use it again from the beginning in the
same manner as before.
• If the heads become dirty soon after cleaning, the
tape may be damaged. In this case, immediately
stop using that Cassette.
• Do not clean the heads excessively. (Excessive
cleaning may cause excessive wear of the heads. If
the heads are worn, images cannot be played back
even after the heads are cleaned.)
• If the dirty heads cannot be cleaned with the Head
Cleaner, the Camcorder needs to be cleaned at a
Servicenter. Please consult a dealer.
• Head cleaning due to dirty heads is not considered
a malfunction of the product. It is not covered by
the warranty.
Periodical Check-up
To maintain the highest image quality, we
recommend replacement of worn parts, such as
heads, etc., after approximately 1000 hours of use.
(This, however, depends on operating conditions,
such as temperature, humidity, dust, etc.)

Optimal Use of the Battery

Battery Characteristics
This Battery is a rechargeable lithium ion battery. Its
ability to generate power is based upon the chemical
reaction that takes place inside it. This reaction is
susceptible to the surrounding temperature and
humidity, and, if the temperature is too high or too
low, the operating time of the Battery becomes
shorter. If the Battery is used in an extremely cold
environment, the Battery may operate only for about
5 minutes. If the Battery becomes extremely hot, a
protective function may operate, and the Battery may
become unusable for a while.
59