Download Print this page
Avanti 57641 Owner's Manual & Safety Instructions

Avanti 57641 Owner's Manual & Safety Instructions

Hvlp turbine spray gun

Advertisement

Owner's Manual & Safety Instructions
Save This Manual
operating, inspection, maintenance and cleaning procedures. Write the product's serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
NOTICE
CLEAN IMMEDIATELY
Clean the Spray Gun
IMMEDIATELY after EVERY
use and when it will be idle
for more than 30 minutes.
Delayed or inadequate
cleaning will permanently
clog the Spray Gun.
Email our technical support at: productsupport@harborfreight.com
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
©
Copyright
2021 by Harbor Freight Tools
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Keep this manual for the safety warnings and precautions, assembly,
Visit our website at: http://www.harborfreight.com
®
. All rights reserved.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
21a

Advertisement

loading
Need help?

Need help?

Do you have a question about the 57641 and is the answer not in the manual?

Questions and answers

Summary of Contents for Avanti 57641

  • Page 1 Owner’s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.
  • Page 2: Table Of Contents

    3. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. Page 2 For technical questions, please call 1-888-866-5797. Item 57641...
  • Page 3 These carry important safety information. Contact the solvent or coating manufacturer as If unreadable or missing, contact needed regarding potential chemical reactions. Harbor Freight Tools for a replacement. Item 57641 For technical questions, please call 1-888-866-5797. Page 3...
  • Page 4 SAVE THESE INSTRuCTIONS. Page 4 For technical questions, please call 1-888-866-5797. Item 57641...
  • Page 5 Do not use solvents improperly. National pipe thread, straight WARNING marking concerning Risk of Electric Shock. WARNING marking concerning Properly connect power cord Risk of Eye Injury. to appropriate outlet. Wear ANSI-approved eye protection. Item 57641 For technical questions, please call 1-888-866-5797. Page 5...
  • Page 6 3. The tool must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances. The plug and outlet should look like those in the preceding illustration. (See 3-Prong Plug and Outlet.) Page 6 For technical questions, please call 1-888-866-5797. Item 57641...
  • Page 7: Specifications

    Canada) to indicate it is acceptable for outdoor use. Specifications Cup Capacity 32 fl. oz. Tip Size 1.3mm NOZZLE CHART Material Thickness Nozzle Size Thin Medium Thick 0.8 mm 1.3 mm 1.8 mm 2.2 mm Item 57641 For technical questions, please call 1-888-866-5797. Page 7...
  • Page 8: Setup

    Attach Spray Gun to Air Hose by pulling down Coupler, inserting Spray Gun Coupler fully into Air Hose, then releasing Coupler. Pull on Air Hose to make sure Spray Gun is fully seated. Coupler Page 8 For technical questions, please call 1-888-866-5797. Item 57641...
  • Page 9: Operation

    2. Before spraying, mask nearby objects not being The work area must not allow access by children sprayed and lay cloths (not included) on the floors. or pets to prevent distraction and injury. Item 57641 For technical questions, please call 1-888-866-5797. Page 9...
  • Page 10 NOTICE: Do not use any kind of lubricant. The lubricant will mix with paint, causing poor results. Waste Disposal After cleaning, dispose of waste according to the solvent manufacturer’s directions and local hazardous waste standards. Page 10 For technical questions, please call 1-888-866-5797. Item 57641...
  • Page 11 Air Control Knob, then spray on scrap material until desired consistency is achieved. 6. If paint is too thick, thin paint according to manufacturer’s instructions and repeat instructions above. Item 57641 For technical questions, please call 1-888-866-5797. Page 11...
  • Page 12 Pattern Adjustment While Spray Gun is facing forward and Trigger is released: a. To increase pattern size, turn Air Cap clockwise. b. To decrease pattern size, turn Air Cap counterclockwise. Page 12 For technical questions, please call 1-888-866-5797. Item 57641...
  • Page 13 NOTICE: Do not use any kind of lubricant. The lubricant will mix with paint, causing poor results. Waste Disposal After cleaning, dispose of waste according to the solvent manufacturer’s directions and local hazardous waste standards. Item 57641 For technical questions, please call 1-888-866-5797. Page 13...
  • Page 14: Maintenance

    • misalignment or binding of moving parts, • clogged fluid nozzle or air cap, • cracked or broken parts, and • any other condition that may affect its safe operation. Page 14 For technical questions, please call 1-888-866-5797. Item 57641...
  • Page 15 Valve 3. Push ends of new Air Tube over fittings on Spray Gun and Cup Lid. If necessary, add a small amount of water as lubricant to interior of tube. Item 57641 For technical questions, please call 1-888-866-5797. Page 15...
  • Page 16 3. Cup and/or Lid loose. 3. Tighten Cup and/or Lid. 4. Clogged Check Valve. 4. Clean Check Valve. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect power supply before service. Page 16 For technical questions, please call 1-888-866-5797. Item 57641...
  • Page 17 3. Airflow too high. 3. Reduce Airflow. 4. Clogged Check Valve. 4. Clean Check Valve. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect power supply before service. Item 57641 For technical questions, please call 1-888-866-5797. Page 17...
  • Page 18: Parts List And Diagram

    Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Parts may not be interchangeable. Specify UPC number when ordering: 193175419248 Page 18 For technical questions, please call 1-888-866-5797. Item 57641...
  • Page 19 Clean the Spray Gun Body and Cup IMMEDIATELY after EVERY use and when it will be idle for more than 30 minutes. Delayed or inadequate cleaning will permanently clog the Spray Gun. Paint hardens quickly and permanently inside Spray Gun. Assembly Diagram Item 57641 For technical questions, please call 1-888-866-5797. Page 19...
  • Page 20: Warranty

    Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.