Cisco N540-FH-CSR-SYS Install Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Network Router
  5. N540-FH-CSR-SYS
  6. Install manual

Cisco N540-FH-CSR-SYS Install Manual

Hide thumbs Also See for N540-FH-CSR-SYS:
Table of Contents

Advertisement

Quick Links

Download this manual
Install the Device
Before you begin this task, ensure that you have read and understood the safety warnings in the Standard
Warning Statements section of the Safety Warnings handout.
•
•
Install N540-FH-CSR-SYS
Installing the Cisco N540-FH-CSR-SYS involves these tasks:
Rack Compatibility
We recommend that you follow these rack specifications.
Rack Types
Figure 1: Rack specification EIA (19 inches and 23 inches)
Install N540-FH-CSR-SYS, on page 1
Install Cisco N540-FH-AGG-SYS, on page 23
Install the Device
1

Advertisement

Table of Contents
loading

Related Manuals for Cisco N540-FH-CSR-SYS

Summary of Contents for Cisco N540-FH-CSR-SYS

  • Page 1 Install N540-FH-CSR-SYS, on page 1 • Install Cisco N540-FH-AGG-SYS, on page 23 Install N540-FH-CSR-SYS Installing the Cisco N540-FH-CSR-SYS involves these tasks: Rack Compatibility We recommend that you follow these rack specifications. Rack Types Figure 1: Rack specification EIA (19 inches and 23 inches)
  • Page 2 Install the Device Rack Types Table 1: Rack specification EIA (19 inches and 23 inches) Post Type Rack Type Rack Front Opening Rack Mounting Hole Mounting Flange Centre-Centre (Y) Dimension (Z) 4 Post 19 inches (48.3 450.8mm (17.75”) 465mm (18.312”) 482.6mm (19”) centimeters) 2 Post...

  • Page 3: Set Up Device On Rack

    Figure 3: Two Post Rack Type Set up Device on Rack You can set up the Cisco N540-FH-CSR-SYS on a rack. Rack Mount The device is shipped with rack mounting brackets that are to be secured on the sides of the device.
  • Page 4 Install the Device Rack Mount 1. Attach the rack-mount brackets and the cable guides to the router as follows: a. The router has port-side intake modules, position the router so that its ports are facing the cold aisle. b. Position the bracket ears facing front or middle rack-mount, on the side of the chassis so that the holes are aligned.
  • Page 5 Install the Device Rack Mount Figure 5: Installing Cable Management and 19 inch Rack-Mount Brackets in the Front Figure 6: Installing Cable Management and 19 inch Rack-Mount Brackets in the Middle Install the Device...
  • Page 6 Install the Device Rack Mount Figure 7: Installing Cable Management and 19 inch Rack-Mount Brackets in the Rear Figure 8: Installing Cable Management and 23 inch Rack-Mount Brackets in the Front Install the Device...
  • Page 7 Install the Device Rack Mount Figure 9: Installing Cable Management and 23 inch Rack-Mount Brackets in the Middle Figure 10: Installing Cable Management and ETSI Rack-Mount Brackets in the Front Install the Device...

  • Page 8: Ground The Device

    Install the Device Ground the Device Figure 11: Installing Cable Management and ETSI Rack-Mount Brackets in the Middle Figure 12: Installing Cable Management and ETSI Rack-Mount Brackets in the Rear Ground the Device Before you begin this task, ensure that you have read and understood the safety warnings in the Preventing ESD Damage section of the Safety Warnings handout.

  • Page 9: Install The Ac Power Cables

    Install the Device Install the AC Power Cables Before you connect the power or turn on the power to the device, you must provide an adequate device ground (earth) connection to your device. This section describes how to ground the device. The grounding lug location is on the back panel of the device. 1.

  • Page 10: Activate An Ac Power Supply Module

    [2, 4] in the figure below. Figure 14: Attach the AC Power Tie-and-Clip Cord Note These images are for only representation purposes. Certain variants of Cisco NCS 540 do not include a tie for the power supply cord. Activate an AC Power Supply Module...

  • Page 11: Install The Dc Power Cables

    When installing DC power supply, use 12AWG, 90°C temperature rated cable. The recommanded cable length is three meters maximum from source. For lengths up to five meters, use 10AWG, and for lengths up to three meters, use 12AWG, 90°C temperature rated cable. For other lengths, contact Cisco. Note •...

  • Page 12: Activate A Dc Power Supply Module

    Install the Device Activate a DC Power Supply Module Figure 16: Attach the DC Power Supply Wires Activate a DC Power Supply Module Perform the following procedure to activate a DC power supply: Step 1 Remove the tape from the circuit-breaker router handle, and restore power by moving the circuit-breaker router handle to the On (|) position.

  • Page 13: Connect To The Console Port

    • Download software updates. The system console port is an RJ-45 receptacle for connecting a data terminal to perform the initial configuration of Cisco NCS 540 fixed-port chassis. The console cable is shipped with the hardware. Note Only RJ45 to DB-9 adapter cable is provided in the package.

  • Page 14: Connect To The Management Ethernet Port

    Install the Device Connect to the Management Ethernet Port Figure 17: Connecting the USB Console Cable to the Chassis RJ45 Port Console cable Follow this procedure to connect a data terminal to the console port: 1. Set your terminal to these operational values: 115200 bps, 8 data bits, no parity, and two stop bits. 2.

  • Page 15: Connecting Timing Cables

    Install the Device Connecting Timing Cables The management Ethernet port provides out-of-band management, which enables you to use the Command Line Interface (CLI) to manage the router by its IP address. This port uses a 10/100/1000 Ethernet connection with an RJ-45 interface. Note To prevent an IP address conflict, do not connect the management Ethernet port until the initial configuration is complete.

  • Page 16: Connecting Cables To A Gps Interface

    Install the Device Connecting Cables to a GPS Interface Connecting Cables to a GPS Interface Note When installing the cables to the RSP, we recommend that you leave a service loop of extra cable to enable fan tray removal. The following sections describe how to connect cables from the router to a GPS unit for input or output timing of frequency: Connecting a Cable to the Input 10-MHz or 1-PPS Interface Step 1...

  • Page 17: Safety Precautions For Module Installation And Removal

    Install the Device Install and Remove Transceiver Module Figure 19: Installing the GNSS Module in the RSP Install and Remove Transceiver Module This section shows how to install and remove transceiver module. Safety Precautions for Module Installation and Removal Be sure to observe the following safety precautions when you work on the chassis. Warning Class 1 laser product.

  • Page 18: Install And Remove Sfp Modules

    Install the Device Install and Remove SFP Modules Warning Do not stare into the beam or view it directly with optical instruments. Statement 1011 Warning Invisible laser radiations present. Statement 1016 Install and Remove SFP Modules Before you remove or install an SFP or SFP+ module, read the installation information in this section. Warning Class I (CDRH) and Class 1M (IEC) laser products.

  • Page 19: Bale Clasp Sfp Or Sfp+ Module

    Install the Device Bale Clasp SFP or SFP+ Module Figure 20: SFP/SFP+ Module Cage Cover Caution Protect the SFP or SFP+ modules by inserting clean dust covers into them after the cables are removed. Be sure to clean the optic surfaces of the fiber cables before you plug them back into the optical ports of another module.

  • Page 20: Install A Bale Clasp Sfp Or Sfp+ Module

    Install the Device Install a Bale Clasp SFP or SFP+ Module Figure 21: Bale Clasp SFP or SFP+ Module Install a Bale Clasp SFP or SFP+ Module To install this type of SFP or SFP+ module: 1. Attach an ESD-preventive wrist or ankle strap and follow its instructions for use. 2.

  • Page 21: Remove A Bale Clasp Sfp Or Sfp+ Module

    Install the Device Remove a Bale Clasp SFP or SFP+ Module Note When installing an SFP or SFP+ module, you should hear a click as the triangular pin on the bottom of the SFP module snaps into the hole in the receptacle. This click indicates that the module is correctly seated and secured in the receptacle.

  • Page 22: Connect Interface Ports

    Install the Device Connect Interface Ports Figure 23: Removing a Bale Clasp SFP or SFP+ Module 5. Place the SFP module that you removed on an antistatic mat, or immediately place it in a static shielding bag if you plan to return it to the factory. 6.

  • Page 23: Maintain Transceivers And Optical Cables

    • Inspect routinely for dust and damage. Clean and then inspect fiber ends under a microscope to determine whether any damage has occurred. Install Cisco N540-FH-AGG-SYS Installing the Cisco N540-FH-AGG-SYS involves these tasks: Rack Compatibility We recommend that you follow these rack specifications.

  • Page 24: Rack Types

    Install the Device Rack Types Rack Types Figure 24: Rack specification EIA (19 inches and 23 inches) Table 4: Rack specification EIA (19 inches and 23 inches) Post Type Rack Type Rack Front Opening Rack Mounting Hole Mounting Flange Centre-Centre (Y) Dimension (Z) 4 Post 19 inches (48.3...
  • Page 25 Figure 25: Four Post Rack Type Set up Device on Rack You can set up the Cisco N540-FH-AGG-SYS on a rack. Rack Mount The device is shipped with rack mounting brackets that are to be secured on the sides of the device.
  • Page 26 Install the Device Rack Mount b. Position the bracket ears facing front or middle rack-mount, on the side of the chassis so that the holes are aligned. c. Position the bracket extension facing rear side so that the holes are aligned properly. d.
  • Page 27 Install the Device Rack Mount Figure 27: Installing Cable Management and 21 inch Rack-Mount Brackets Figure 28: Installing Cable Management and 23 inch Rack-Mount Brackets Install the Device...
  • Page 28 Install the Device Rack Mount Figure 29: Installing 19 inch Rack-Mount Brackets in the Middle with Cable Management Attached in Front Position Bracket Figure 30: Installing 21 inch Rack-Mount Brackets in the Middle with Cable Management Attached in Front Position Bracket Install the Device...
  • Page 29 Install the Device Ground the Device Figure 31: Installing 23 inch Rack-Mount Brackets in the Middle with Cable Management Attached in Front Position Bracket Ground the Device Before you begin this task, ensure that you have read and understood the safety warnings in the Preventing ESD Damage section of the Safety Warnings handout.
  • Page 30 Install the Device Install the AC Power Cables Figure 32: Ground Lug 2. Attach one end of the shelf ground cable (#6 AWG cable) to the ground point on the rear of the chassis using the specified dual-hole lug connector. •...
  • Page 31 Activate an AC Power Supply Module Figure 33: Attach the AC Power Tie-and-Clip Cord Note These images are for only representation purposes. Certain variants of Cisco NCS 540 do not include a tie for the power supply cord. Activate an AC Power Supply Module...
  • Page 32 When installing DC power supply, use 12AWG, 90°C temperature rated cable. The recommanded cable length is three meters maximum from source. For lengths up to five meters, use 10AWG, and for lengths up to three meters, use 12AWG, 90°C temperature rated cable. For other lengths, contact Cisco. Note •...
  • Page 33 Install the Device Activate a DC Power Supply Module Figure 35: Attach the DC Power Supply Wires Activate a DC Power Supply Module Perform the following procedure to activate a DC power supply: Step 1 Remove the tape from the circuit-breaker router handle, and restore power by moving the circuit-breaker router handle to the On (|) position.
  • Page 34 • Download software updates. The system console port is an RJ-45 receptacle for connecting a data terminal to perform the initial configuration of Cisco NCS 540 fixed-port chassis. The console cable is shipped with the hardware. Note Only RJ45 to DB-9 adapter cable is provided in the package.
  • Page 35 Install the Device Connect to the Management Ethernet Port Figure 36: Connecting the USB Console Cable to the Chassis RJ45 Port Console cable Follow this procedure to connect a data terminal to the console port: 1. Set your terminal to these operational values: 115200 bps, 8 data bits, no parity, and two stop bits. 2.
  • Page 36 Install the Device Connecting Timing Cables The management Ethernet port provides out-of-band management, which enables you to use the Command Line Interface (CLI) to manage the router by its IP address. This port uses a 10/100/1000 Ethernet connection with an RJ-45 interface. Note To prevent an IP address conflict, do not connect the management Ethernet port until the initial configuration is complete.
  • Page 37 Install the Device Connecting a Cable to the Input 10-MHz or 1-PPS Interface Connecting a Cable to the Input 10-MHz or 1-PPS Interface Connect one end of a mini-coax cable to the GPS unit. Connecting a Cable to the Output 10MHz or 1PPS Interface Step 1 Connect one end of a mini-coax cable to the Slave unit.
  • Page 38 Install the Device Install and Remove Transceiver Module Install and Remove Transceiver Module This section shows how to install and remove transceiver module. Safety Precautions for Module Installation and Removal Be sure to observe the following safety precautions when you work on the chassis. Warning Class 1 laser product.
  • Page 39 Install the Device Remove a Bale Clasp SFP or SFP+ Module 3. Line up the SFP module with the port and slide it into the port. (See the figure below.) Figure 40: Installing a Bale Clasp SFP Module into a Port Note When installing an SFP or SFP+ module, you should hear a click as the triangular pin on the bottom of the SFP module snaps into the hole in the receptacle.
  • Page 40 Install the Device Remove a Bale Clasp SFP or SFP+ Module Figure 41: Removing a Bale Clasp SFP or SFP+ Module 5. Place the SFP module that you removed on an antistatic mat, or immediately place it in a static shielding bag if you plan to return it to the factory.
  • Page 41 Install the Device Connect Interface Ports Connect Interface Ports You can connect optical interface ports on line cards with other devices for network connectivity. Connect a Fiber-Optic Port to the Network Depending on the line card model that you are using, you can use either QSFP+ or QSFP28 transceivers. Some transceivers work with fiber-optic cables that you attach to the transceivers and other transceivers work with pre-attached copper cables.
  • Page 42 Install the Device Maintain Transceivers and Optical Cables Install the Device...

Table of Contents