Advertisement
Product Name:
SKU #:
Thank you for purchasing this Luxen Home product. This product has been manufactured with the highest
standards of safety and quality.
PLEASE READ ALL INSTRUCTIONS BEFORE ASSEMBLY.
Unpack all parts from Styrofoam and bubble wrap inside the carton to ensure there are no missing or damaged
parts. If any parts are missing or damaged, do not attempt to assemble or use the product.
CARTON CONTENTS:
Description
Fountain
Pump
Compatible Pumps for this fountain:
Pump Model No.
JR350/LED
JB350/LED
YH400/LED
Tools required for assembly: No tools required for assembly.
Assembly Instructions:
1. Unpack the contents of the box and check to make sure that all items are accounted for and in good
condition.
2. Select a flat, level surface for the assembly and final location of your fountain.
3. From the opening at the back of the fountain, insert the water supply tube into the pump outlet. Insert the
LED connector into the pump connector, and twist to tighten. Place the pump inside the back of the
fountain, and draw the pump power cord out of the fountain back.
4. Add clean water to the fountain. The water level should be approximately 30mm lower than the edge of the
basin.
5. Connect the power cable to outlet. If installed properly, water flow in the fountain will begin shortly.
6. Please do not use the electrical plug in wet weather conditions. Please note: On first use, there may be air in
the pump. It may take several minutes until all the air escapes.
7. To eliminate the possibility of water damage around your fountain, check for leaks and excessive splashing
after the initial setup of your fountain. It is highly recommended that this fountain be placed in an area
where it cannot be damaged.
8. Do not leave your fountain running for extended periods of time when no one is present to observe the
performance.
9. Check the area around your fountain on a regular basis to ensure that there is no leakage.
10. Please refresh the fountain with water each week to ensure it in good condition.
Resin Old Man Tree Outdoor Fountain
WHF1021
Quantity
1
1
Contact: cs@winsomehouse.com
Instruction Manual
Please save this manual for future reference.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Luxen Home WHF1021
Summary of Contents for Luxen Home WHF1021
- Page 1 Resin Old Man Tree Outdoor Fountain SKU #: WHF1021 Thank you for purchasing this Luxen Home product. This product has been manufactured with the highest standards of safety and quality. PLEASE READ ALL INSTRUCTIONS BEFORE ASSEMBLY. Unpack all parts from Styrofoam and bubble wrap inside the carton to ensure there are no missing or damaged parts.
- Page 2 Please save this manual for future reference. Product Name: Resin Old Man Tree Outdoor Fountain SKU #: WHF1021 11. Do not add any harmful chemicals to the water as it may alter the finish. Note: The above diagram is for illustrative purposes only. Contact: cs@winsomehouse.com...
- Page 3 Instruction Manual Please save this manual for future reference. Product Name: Resin Old Man Tree Outdoor Fountain SKU #: WHF1021 Pump Instructions: Special Warnings and Cautions: CAUTION: • The pump has been evaluated for use with water only. Risk of electric shock. Do not remove cord and strain relief. Do not connect conduit to pump.
- Page 4 Product Name: Resin Old Man Tree Outdoor Fountain SKU #: WHF1021 WARNINGS: 1. To reduce the risk of electric shock, connect only to a properly grounded, grounding type receptacle. 2. To reduce the risk of electric shock, use only on portable self-contained fountains no larger than 5 feet in any dimension.
- Page 5 Please save this manual for future reference. Product Name: Resin Old Man Tree Outdoor Fountain SKU #: WHF1021 CARE & MAINTENANCE: 1. Keep the water clean – clean water will prolong the useful life of your pump. 2. Use a pre-filter on your pump if available.
Need help?
Do you have a question about the WHF1021 and is the answer not in the manual?
Questions and answers