Luxen Home WHF1053 Instruction Manual

Luxen Home WHF1053 Instruction Manual

Metal crane and flowers outdoor resin fountain with solar light

Advertisement

Quick Links

Metal Crane and Flowers Outdoor Resin Fountain with Solar Light
Product Name:
SKU #:
WHF1053
Thank you for purchasing this Luxen Home product. This product has been manufactured with the highest
standards of safety and quality.
PLEASE READ ALL INSTRUCTIONS BEFORE ASSEMBLY.
Unpack all parts from Styrofoam and bubble wrap inside the carton to ensure there are no missing or damaged
parts. If any parts are missing or damaged, do not attempt to assemble or use the product.

CARTON CONTENTS:

Description
Fountain Base
Fountain Crane (Top)
Solar Panel
Pump
Compatible Pumps for this fountain:
Pump Model No.
JR-250
JB333
YH300-70
Tools required for assembly: No tools required for assembly.

Assembly Instructions:

1. Unpack the contents of the box and check to make sure that all items are accounted for and in good
condition.
2. Select a flat, level surface for the assembly and final location of your fountain.
3. Place solar panel for the light on the back of the crane.
4. Insert the water supply tube located on the underside of the crane fountain top into the pump. Place the
pump upright in the basin and draw the pump power cord out of the fountain back. Place the fountain crane
top on the base.
5. Add clean water into the basin. The water level should be approximately 1.18in (30mm) lower than the edge
of the basin. The pump will be submerged in the water.
6. Connect the pump power cord to a ground fault circuit interrupter (GFCI) outlet and the product will begin
to function as intended.
7. To eliminate the possibility of water damage around your fountain, check for leaks and excessive splashing
after the initial setup of your fountain. It is highly recommended that this fountain be placed in an area
where it cannot be damaged.
8. Do not leave your fountain running for extended periods of time when no one is present to observe the
performance.
9. Check the area around your fountain on a regular basis to ensure that there is no leakage.
Quantity
1
1
1
1
Contact: cs@winsomehouse.com
Please save this manual for future reference.
Instruction Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WHF1053 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Luxen Home WHF1053

  • Page 1 Product Name: SKU #: WHF1053 Thank you for purchasing this Luxen Home product. This product has been manufactured with the highest standards of safety and quality. PLEASE READ ALL INSTRUCTIONS BEFORE ASSEMBLY. Unpack all parts from Styrofoam and bubble wrap inside the carton to ensure there are no missing or damaged parts.
  • Page 2 Metal Crane and Flowers Outdoor Resin Fountain with Solar Light Product Name: SKU #: WHF1053 10. Please refresh the fountain with water each week to ensure it in good condition. 11. Do not add any harmful chemicals to the water as it may alter the paint finish.
  • Page 3 Instruction Manual Please save this manual for future reference. Metal Crane and Flowers Outdoor Resin Fountain with Solar Light Product Name: SKU #: WHF1053 Pump Instructions: Special Warnings and Cautions: CAUTION: • The pump has been evaluated for use with water only.
  • Page 4 Metal Crane and Flowers Outdoor Resin Fountain with Solar Light Product Name: SKU #: WHF1053 WARNINGS: 1. To reduce the risk of electric shock, connect only to a properly grounded, grounding type receptacle. 2. To reduce the risk of electric shock, use only on portable self-contained fountains no larger than 5 feet in any dimension.
  • Page 5 Metal Crane and Flowers Outdoor Resin Fountain with Solar Light Product Name: SKU #: WHF1053 TIPS AND TROUBLESHOOTING: 1. Ensure that the pump’s flow control switch is set to maximum (+) before operating. Once the flow is established, the pump can be adjusted downward to the desired level.

Table of Contents