Page 1
HƯỚNG DẪN SỬ DỤNG VÀ VẬN HÀNH CÂN KỸ THUẬT FRH300 (CÂN ĐIỆN TỬ THỊNH PHÁT biên soạn dựa theo tài liệu hãng). do TPS OEM Original Equipment Manufacturer được Công ty Cổ Phần Cân Điện Tử Cân kỹ thuật FRH300 Thịnh Phát có...
Page 2
Chuẩn bị quả cân cấp chính xác F1. Có 2 cách hiệu chuẩn Hiệu chuẩn thông thường: Mở cân bằng nút "On/OFF" cân sẽ hiển thị TPS trước và đợi cân test Cách 1 từ FFFFF, EEEE, dddd, ccccc, bbbbb, AAAAA sau đó test từ 9999999 về 0000000 khi nào màn hình hiển thị - ------ ta nhấn phím ZERO cân hiện hiển thị...
Page 3
Pin sạc sử dụng pin sạc 6V/1.3AH kích thước (97 x 24 x 52) mm, sử dụng trong 80 giờ cho 1 lần Cân kỹ thuật FRH300 sạc đầy. Khi cân ở vị trí có biểu tượng PIN xuống nấc cuối cùng thì nên sạc nguồn cho cân, thời gian xạc lần đầu là 8 giờ...
FRH300 SAFETY PRECAUTIONS All safety messages are identified by the words "WARNING" and "CAUTION". These words mean the following: △ ! WARNING Important information to alert you to a situation that might cause serious injury and damage to your property if instructions are not followed.
Page 7
FRH300 CAUTIONS: 1. When the recharging sign “ ” indicates, please charge the battery for 8 to 10 hours. When the charging is done, the Orange indicate lights will turn into Green. Over-time charging will cause permanent damage. 2. To use only the charger (adapter) supplied with the indicator.
FRH300 FUNCTION SETTINGS 1.Press [ON/OFF] to turn on the scale, the display will show flash digits and then --------, press [PRINT] ( this function is selectable), the display will show b XXXX value ( press [UNIT] to select among 1200,2400,4800,9600), our default setting is 9600. Press [ZERO] to enter Parity mode, the display will show P XXX, press [UNIT] to select odd, even, none (odd stands for 7 data bits with odd parity, even stands for 7 data bits with even parity, none stands for 8 data bit without parity)our default setting is none.
FRH300 WEIGHING Before weighing Whenever possible, please allow the balance to warm up for 10 minutes after first turning to power on, so that the balance will function properly and accurately. Error messages Err-O: Overload Low battery Calibration may be required before weighing.
Page 10
FRH300 1/120000&1/200000 division available CALIBRATION When to calibrate Calibration may be required when it is initially installed, if the scale/balance is moved to a substantial distance. This is necessary because the weight of a mass in one location is not necessarily the same in another location. Also, with time and use, mechanical deviations may occur.
FRH300 SPECIFICATIONS Model VB302B VB302B FRH300 FRH600 Capacity 300 g 600 g 300 g 600 g Readability 0.01 g 0.01 g 0.01 g 0.01 g Pan Size Ø 115 mm Overall Size (260 x 185 x 90) mm. Weighing Units g, lb, tl.T, PCS...
Need help?
Do you have a question about the FRH300 and is the answer not in the manual?
Questions and answers