Subscribe to Our Youtube Channel
Related Manuals for Dahua HD Box
Summary of Contents for Dahua HD Box
- Page 1 HD Box Network Camera Quick Start Guide ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD. V1.0.1...
-
Page 2: Foreword
Quick Start Guide Foreword General This manual introduces the functions, installation and operations of the camera. Safety Instructions The following categorized signal words with defined meaning might appear in the manual. Signal Words Meaning Indicates a medium or low potential hazard which, if not avoided, could result in slight or moderate injury. - Page 3 Quick Start Guide occurring when using the device. If there is any uncertainty or controversy, we reserve the right of final explanation. ...
-
Page 4: Important Safeguards And Warnings
Quick Start Guide Important Safeguards and Warnings Electrical safety All installation and operation should conform to your local electrical safety codes. The power source shall conform to the Safety Extra Low Voltage (SELV) standard, and supply power with rated voltage which conforms to Limited Power Source requirement according to IEC60950-1. - Page 5 Quick Start Guide It is recommended connect the grounding hole to the ground to enhance the reliability of the device. Do not touch the image sensor directly (CMOS). Dust and dirt could be removed with air blower, or you can wipe the lens gently with soft cloth that moistened with alcohol. Device body can be cleaned with soft dry cloth, which can also be used to remove stubborn ...
-
Page 6: Table Of Contents
Quick Start Guide Table of Contents Foreword ................................II Important Safeguards and Warnings ......................IV 1 Introduction ..............................1 Device Structure ..................................1 Connecting Alarm Input/output ............................4 2 Network Configuration ..........................6 Initializing Device ..................................6 Modifying Device IP Address ..............................7 Logging in to Web Interface.............................. -
Page 7: Introduction
Quick Start Guide Introduction Device Structure Structure type might vary with different devices, and the actual product shall prevail. Figure 1-1 Device Structure Figure 1-2 Device Structure... - Page 8 Quick Start Guide Figure 1-3 Device Structure For more information about ports, see Table 1-1. Table 1-1 Port Information Port Name Port Function VIDEO OUT Video output port Outputs analog video signal. It can connect to TV monitor to check image. Previews image via the DVR which supports ...
- Page 9 Quick Start Guide Port Name Port Function Ground end of RS232 serial port. RS232 port Sending end of RS232 serial port Receiving end of RS232 serial port RS485 port RS485_B port, control external PTZ etc. RS485_A port, control external PTZ etc. IR light port External IR light signal control port.
-
Page 10: Connecting Alarm Input/Output
Quick Start Guide Port Name Port Function Some devices are only equipped with 1 channel audio input port. /OPT Network port /MB LAN: Connect to standard Ethernet cable and optical fiber port provide PoE power supply function. OPT: Transmit MB Ethernet data. SD card port Connects to SD card. - Page 11 Quick Start Guide Figure 1-5 Alarm output Step 3 Log in web interface, and configure alarm input and alarm output in alarm setting. The alarm input in the web interface is corresponding to the alarm input end of the I/O ...
-
Page 12: Network Configuration
Quick Start Guide Network Configuration Device initialization and IP setting can be finished with the "ConfigTool" or in web interface. For more information, see the WEB operation manual. Device initialization is available on select models, and it is required at first use and after device is ... -
Page 13: Modifying Device Ip Address
Quick Start Guide The Device initialization interface is displayed. Select the devices that need initialization, and then click initialize. Step 6 The password setting interface is displayed. See Figure 2-2. Figure 2-2 Password setting interface Step 7 Set and confirm the password of the devices, and then enter a valid email address. Click Next. -
Page 14: Logging In To Web Interface
Quick Start Guide Select the devices which IP addresses need to be modified, and then click Modify IP. Step 3 The Modify IP Address interface is displayed. See Figure 2-3. Figure 2-3 Modify IP Address interface Select Static mode and enter start IP, subnet mask and gateway. Step 4 IP addresses of multiple devices will be set to the same if you select Same IP. -
Page 15: Installation
Quick Start Guide Installation Packing List The tool required for the installation such as electric drill is not provided in the packing. The operation manual and related tool are contained in the disk or the QR code, and the actual ... - Page 16 Quick Start Guide Model B (Unit: mm [in]) Model C (Unit: mm [in])
-
Page 17: Installing Device
Quick Start Guide Installing Device 3.3.1 Installation Method Indoor Wall-mounted Indoor Hang-mounted Please use housing if the device needs to be installed outdoors, which is to avoid device damage caused by water soaking. Figure 3-1 Install Housing 3.3.2 Installing Lens Auto iris socket: it needs to plug the cable of auto iris lens into auto iris socket when the installed lens is auto iris lens. -
Page 18: Attaching Device
Quick Start Guide Figure 3-2 Bayonet Mount Figure 3-3 Screw-threaded Mount CS Lens C Lens 3.3.3 Attaching Device Make sure the mounting surface is strong enough to hold at least three times of the device weight. - Page 19 Quick Start Guide Cable going through the wall...
-
Page 20: Using I/O Port
Quick Start Guide Cable going through the cable tray 3.3.4 Using I/O Port... -
Page 21: Adjusting Angle
Quick Start Guide 3.3.5 Adjusting Angle... - Page 22 Quick Start Guide...
Need help?
Do you have a question about the HD Box and is the answer not in the manual?
Questions and answers