Advertisement
Troubleshooting
[EN]
Please read this section for troubleshooting before requesting repair services.
Trouble
Inserting hands does not activate the dryer
Removing hands does not stop the dryer
No warm air blows
The dryer does not supply enough air
If the problem still persists after performing suggested actions, turn off the power switch and set the breaker to "Off."
Then consult with the installation contractor (or the shop where you purchased the unit).
( See the back cover of this manual for contact details.)
Indicators
Status indicator lights
LED
Always On
ON
OFF
LED
Flashes once
ON
OFF
Flashes twice
LED
ON
OFF
8
Solutions
● Power Switch might be set to OFF.
→If so, set Power Switch to ON. (See page 3)
● Has the Circuit Breaker ON been tripped?
→If it is OFF, please reset it.
● Is there any obstruction in the waste pan ?
→ If there is any obstruction, please remove it.
● Is the sensor dirty?
→If the sensor is not clean, wipe it with a soft damp cloth. (See page 6)
● Is there any obstruction in the waste pan ?
→ If there is any obstruction, please remove it.
● Is the sensor dirty?
→If the sensor is not clean, wipe it with a soft damp cloth. (See page 6)
● Heater Power Switch might be set to OFF.
→If so, set Heater Power Switch to ON. (See page 3)
● Has Filter accumulated dust or debris?
→Clean Filter if there is an accumulation of dust or debris. (See page 7)
Operation of the product
Meaning of the indicators
Corrective actions
An indicator is lit dimly all the time.
Power is being supplied
(Standby)
Sensors keep
The dryer may operate even if
malfunctioning
some sensors malfunction.
Make sure that sensors are clean.
If they are not clean, wipe them with
a soft damp cloth. ( See page 8)
If the indicator does not turn off
after performing these actions,
consult with the installation
contractor (or the shop where you
bought the unit).
The dryer is not working.
Fan motor is malfunctioning
Clean the filter if it is dirty.
( See page 9)
Thermistor is malfunctioning
Clean the bottom of the unit if it is
dirty.
Problem with temperature
The dryer is not working.
fuse
Replacing it may solve the problem.
Consult with the installation
Controller is malfunctioning
contractor (or the shop where you
bought the unit).
疑难排解
[中文]
疑似故障时，请于委托维修前，确认以下事项。
现象
● 电源开关是否处于"关"状态？
即使将手伸进去也不吹出干燥风
→ 如果处于"关"的状态，请将其设置为"开"。（参照第3页）
● 室内电流断路器是否处于"关"的状态？
→ 如果断开，请合上。
● 蓄水部内是否有异物？
→ 有异物的情况下请将异物清除。
● 感应器部是否有污渍？
→ 如果出现污渍，请将用水浸湿的柔软的布充分拧干以后，将污渍清除。
（参照第6页）
● 蓄水部内是否有异物？
即使抽出手，干燥风也不停止
→ 有异物的情况下请将异物清除。
● 感应器部是否有污渍？
→ 如果出现污渍，请将用水浸湿的柔软的布充分拧干以后，将污渍清除。
（参照第6页）
不出温风
● 加热器切换开关是否处于"关"状态？
→ 如果处于"关"的状态，请将其设置为"开"。（参照第3页）
风量小
● 过滤网上是否积有灰尘或垃圾？
→ 如果积有灰尘或垃圾，请进行清扫。（参照第7页）
如果对上述事项进行确认以后，仍然存在问题，请关闭产品电源，关闭电源总开关，与东陶（中国）有限公司的工作人员进行协商。
关于照明显示
照明表示状态
正
待
LED
平时ON
常
机
照明
时
时
ON
OFF
闪
烁
LED
一个闪光
模
照明
ON
式
OFF
①
出
现
错
误
时
闪
烁
模
两次闪光
LED
式
ON
照明
②
OFF
解决方法
表示内容
产品的动作/处理内容
电源通电（待机时）
平时，照明灯比较昏暗。
感应器连续感知异常
即使一部分的感应器异常，
产品也能感知启动。
请确认感应器是否出现污渍。
如果出现污渍，请用柔软的布浸湿拧干后，
将污渍清除。（ 参照第8页）
如果这样还无法消除错误，
请联系东陶（中国）有限公司。
风扇马达异常
无法启动。
如果是过滤网上布满了灰尘或垃圾，
热敏电阻异常
请将灰尘或垃圾清除。
（ 参照第9页）
如果是产品的下部有灰尘或垃圾，
请将灰尘或垃圾清除。
温度保险丝异常
无法启动。
此时需要更换，
请联系东陶（中国）有限公司。
9
Advertisement
