Advertisement
Quick Links
Mounts by
A division of David Engineering & Mfg. Inc.
Model psfm3042
Thank you for purchasing the PDR product
To ensure the correct usage, please read and follow the instructions manual thoroughly. Please store the instructions in a safe
place for future reference.
All PDR mounts and adapters carry a limited lifetime warranty against defects in material and workmanship.
Check the PDR website for details @ www.PDRmounts.com. We are not liable for improper installation that results in damage
to mounts, adapters or presentation equipment.
Special techniques are necessary for installation of the panel display mount.
Do not attempt to perform this work by yourself.
Ÿ
Request an installation specialist to install this unit.
Ÿ
Manufacturer assumes absolutely no responsibility for injuries and damages that may occur due to improper installation and handling.
Ÿ
Please remember that if you remove the panel display from the wall later, you will find the screw holes and anchor bolts for the mounting
Ÿ
unit left on the wall. Also note that long use of the panel display may discolor the wall around it due to its heat and airflow.
To ensure customer safety, be sure to decide the installation location so that the strength is sufficient to withstand the weight of both the display and the
mount.
Always use at least two persons for all installations.
Fully tighten all of the mounting screws as specified in the installation instructions.
Simple 3 piece design
Ÿ
Low profile 1 1/4"
Ÿ
Fits displays with mounting holes not exceeding
Ÿ
639mm left to right and 350mm top to bottom
Recommended for 30" to 42" display
Ÿ
Tilt and lock mounting (patent pending)
Ÿ
125lb load rated
Ÿ
Wall mount to 16" or 24" wood stud location
Ÿ
Lifetime warranty
Ÿ
Made in the USA
Ÿ
Features
1
Advertisement
Related Manuals for David Engineering & Mfg PDR psfm3042
Summary of Contents for David Engineering & Mfg PDR psfm3042
- Page 1 Mounts by A division of David Engineering & Mfg. Inc. Model psfm3042 Thank you for purchasing the PDR product To ensure the correct usage, please read and follow the instructions manual thoroughly. Please store the instructions in a safe place for future reference. All PDR mounts and adapters carry a limited lifetime warranty against defects in material and workmanship.
-
Page 2: Installation Location
INSTALLATION LOCATION WARNING The wall where the wall mount is to be installed must be capable of long-term support of the total load of the panel display and wall mount. Measures should also be taken to ensure sufficient strength to withstand the force of earthquakes, vibration and other external forces. - Page 3 DRAWING SPECIFICATIONS 660mm 26.00” 31.5mm 639mm 1.24” 25.18” 350mm 16.13” 13.78” 409mm 25mm ø .98” 8 mm...
-
Page 4: Parts List
PARTS LIST Display bracket ..2 pcs Wall mount bracket…1 pc 5/16" Flat washers…4 pcs 4 mm steel flat washer... 4 pcs 4mm x 16 phillips screw... 4pcs 5/16" x 2 1/2” Lag bolts …4 pcs 5 mm x 40 mm Phillip screws...4 pcs 5 mm x 16 mm Phillip screws…4 pcs 6 mm x 16 mm Phillip screws…4 pcs 6mm x 40mm Philips screws...4pcs... - Page 5 MOUNTING THE ARMS TO THE DISPLAY Place the display panel face down on a protected surface. Position the bracket (A) with the slots facing towards the top See Fig 1 & Fig 2 Attach the bracket using the mounting holes that will place the top of the bracket closest to the top of the display, using the proper screws and the square multi-mount washers supplied ( E,F,G,J and H) NOTE : In some applications the plastic spacer ( N ) and longer screws ( K,L,M )may be required to add clearance for the back panel to allow enough tilt to locate on the wall mount bracket ( B )
- Page 6 FASTEN MOUNTING PLATE TO WALL The bracket must be secured to the center of the wall studs capable of holding at least four times the weight of the unit. Use a stud finder to determine the stud center line of the wall stud. Use the sketch from FIG 2 to determine the height of the wall mount bracket (B).
- Page 7 this page is blank...