Advertisement
Quick Links
Mounts by
A division of David Engineering & Mfg. Inc.
Model
AWM250 ARTICULATING WALL MOUNT INSTRUCTIONS
Thank you for purchasing the PDR mount.
To ensure the correct usage, please read and follow the instructions manual thoroughly. Please store the instructions in a safe place
All PDR mounts and adapters carry a limited lifetime warranty against defects in material and workmanship. We are not liable
for improper installation that results in damage to mounts, adapters or presentation equipment.
To register visit our web site @ www.pdrmounts.com
Special techniques are necessary for installation of the panel display mount.
Do not attempt to perform this work by yourself.
Request an installation specialist to install this unit.
Manufacturer assumes absolutely no responsibility for injuries and damages that may occur due to improper installation and handling.
Please remember that if you remove the panel display from the wall later, you will find the screw holes and anchor bolts for t
mounting unit left on the wall. Also note that long use of the panel display may discolor the wall around it due to its heat a
airflow.
To ensure customer safety, be sure to decide the installation location so that the strength is sufficient to withstand the weight
display and the wall mount.
Always use at least two persons for all installations.
Fully tighten all of the mounting screws as specified in the installation instructions.
Features
Features:
Simple to adjust
250 lb load rating ( 50" to 71" TV max recommended ) adapter may be required for large displays
Rugged heavy gauge metal construction
Tension adjustment on all joints "ANTI-CREEP TENSION ADJUSTMENT"
Tough powder-coated "Matte Black" finish
Extends 26.9" from wall and closes to 4.7"
Pivots left or right tilts up 5 deg, down 15deg
Cable management included
Limited lifetime manufacturer warranty on defects in material or workmanship
Made in the USA
Fig 1
1
for future reference.
he
nd
of both the panel
Advertisement
Related Manuals for David Engineering & Mfg PDR MOUNTS AWM250
Summary of Contents for David Engineering & Mfg PDR MOUNTS AWM250
- Page 1 Mounts by A division of David Engineering & Mfg. Inc. Model AWM250 ARTICULATING WALL MOUNT INSTRUCTIONS Thank you for purchasing the PDR mount. To ensure the correct usage, please read and follow the instructions manual thoroughly. Please store the instructions in a safe place for future reference.
-
Page 2: Installation Location
INSTALLATION LOCATION WARNING The wall where the wall mount is to be installed must be capable of long-term support of the total load of the panel display and wall mount. Measures should al so be taken to ensure sufficient strength to withstand the force of earthquakes, vibration and other external forces. - Page 3 DRAWING SPECIFICATIONS 15° 26.87 FULLY EXTENDED 5° 32.00” 4.68” 29.5 max” 1.75 min” 13.76” 24.61 25.50” .32 DIA TYP...
-
Page 4: Mounting Hardware
MOUNTING HARDWARE M8 X 16 PAN HEAD PHILLIPS MACHINE SCREW 5-16 X 2 1/2 LAG BOLT 4 REQUIRED 6 REQUIRED 5/16 X 7/8 USS STEEL M6 X 16 PAN HEAD FLAT WASHER PHILLIPS MACHINE SCREW 6 REQUIRED 4 REQUIRED M5 X 16 PAN HEAD PHILLIPS MACHINE SCREW 4 REQUIRED SQUARE MULTI WASHER... -
Page 5: Wall Mounting Plate
1. FASTEN MOUNTING PLATE TO WALL Determine the exact mounting location for the wall mounting plate prior to the installation, considering the swing of the articulating arm. The plate must be secured to the CENTER of the wall studs capable of at least (4) times the weight of the display and AWM250 . - Page 6 3. SECURE THE DISPLAY BRACKETS TO THE MO NITOR Place the display panel on a protected surface. Position the display bracket with the round holes towards the bottom See Fig 3 Position the brackets equal distance from the bottom and top. Using the proper screws and the square multi washers supplied (1,2,3,8),insert and tighten hardware.
- Page 7 4. TYPICAL PDR PANEL MOUNTING TO ARTICULATING ARM, TENSION CONTROL Lift the display with the wall arms attached on to the AWM250 and center the display on the mounting plate. Assemble the locking tab (items 9 & 10) and insert into the slot in the display arm. (See Fig 4a & 4b) Center the display on the mounting plate and tighten the screws (10) on the locking tab (9).
- Page 8 5. DISPLAY PANEL ADJUSTMENT AND CABLE MANAGEMENT After placing the display on to the AWM250 articulating arm and securing the locking screw tabs, fine adjustments can be made for your best viewing. If the display is not level from left to right Loosen the display leveling bolts and adjust the display and re-tighten the bolts. To tilt the display up or down, loosen the tilt lock knob and adjust with the fine tilt adjuster to the desired view angle.