Advertisement
Quick Links
Operation Manual
Multifunctional Sharpening Station
51251
Illustration similar, may vary depending on model
Please read and follow the operating instructions and safety information prior to initial operation.
Technical changes reserved!
Illustrations, functional steps and technical data may deviate insignificantly due to continuous further
developments.
Advertisement
Summary of Contents for WilTec 51251
- Page 1 Operation Manual Multifunctional Sharpening Station 51251 Illustration similar, may vary depending on model Please read and follow the operating instructions and safety information prior to initial operation. Technical changes reserved! Illustrations, functional steps and technical data may deviate insignificantly due to continuous further...
- Page 2 The information contained in this document may alter at any time without prior notice. No part of this document may be copied or otherwise duplicated without prior written consent. All rights reserved. WilTec Wildanger Technik GmbH cannot be held liable for any possible mistakes in this operating man- ual, nor in the diagrams and illustrations shown.
- Page 3 Before removing a module, pull out the power plug and wait for the grinding disc to come to rest. Precautions concerning user • Do not wear loose clothes, ties, rings, bracelets, or other pieces of jewellery that could be caught by moving parts. © by WilTec Wildanger Technik GmbH Item 51251 Page 3 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 4 2. Remove the fastener from the fastener support and insert the drill to be sharpened (1a). Slightly screw the fastener so that the drill is still easy to be moved. © by WilTec Wildanger Technik GmbH Item 51251 Page 4 http://www.WilTec.de...
- Page 5 180°; thus, the face with the step will point downwards, towards the drill. Grinding knives and pairs of scissors 1. Knife-grinding slot Grinding knives 2. Scissors-grinding slot Grinding scissors © by WilTec Wildanger Technik GmbH Item 51251 Page 5 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 6 7. Repeat, if necessary, until the blades are well sharpened. 8. Switch the device off. Before removing the module, make sure that the grinding disc has come to a rest. © by WilTec Wildanger Technik GmbH Item 51251 Page 6 http://www.WilTec.de...
- Page 7 9. If grinding small chisels, set the appropriate guide to the spacer plate and sharpen as described above (3g). 10. Switch the power off. Before removing the module, make sure that the grinding disc has come to a standstill. © by WilTec Wildanger Technik GmbH Item 51251 Page 7 http://www.WilTec.de http://www.aoyue.eu...
- Page 8 11. After grinding, it is recommended to resharpen the point of the blade with the help of a knife grinder. Attention! When the device is not used, remove the following accessories: • drill chuck (15) • fastener-holder for scissors (25) • blade holder (26) © by WilTec Wildanger Technik GmbH Item 51251 Page 8 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 9 Flexible foot Magnet Screw Screw Drill chuck Locking tube Supporting chuck Fuse Locking piece Locking tube Gripping piece Auxiliary switch Lock nut Interrupter Interrupter board Cylinder © by WilTec Wildanger Technik GmbH Item 51251 Page 9 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 10 German law related to electrical and electronic equipment and appliances. All WilTec electric devices that fall under the WEEE directive are labelled with the symbol of a crossed- out wheeled rubbish bin. This symbol indicates that this electric device must not be disposed of with the domestic waste.