Related Manuals for Daikin MC704AVM
Summary of Contents for Daikin MC704AVM
- Page 1 OPERATION MANUAL MODEL MC704AVM PHOTOCATALYTIC AIR PURIFIER English Deutsch Français Nederlands Español Italiano ΕλληνικÜ Portugues Рóссêий...
-
Page 2: Table Of Contents
Specification 4 7 year pre-cut Titanium apatite photocatalytic filter roll Tremendous advantage with durable filter 5 Designed for Quiet Operation Model MC704AVM Security when sleeping Required power supply 1ø220-240/220-230V 50/60Hz Outer dimensions 400×498×198... -
Page 3: Safety Precautions
Safety Precautions • Keep this manual where the operator can easily find them. • Do not use near to sources of heat such as heaters. • Read this manual attentively before starting up the unit. Heat can discolor and deform the casing. •... -
Page 4: Names And Operation Of Each Part
Names and Operation of each Part ■ ■ ■ ■ Main unit Front Rear 1 Front panel CAUTION 2 Main unit display (Page 4) • Do not strongly press on the photocatalyst. Shows operation status. The special inverter lamp located inside may be damaged. 3 Knob for panel disassembly •... - Page 5 ■ ■ ■ ■ Main unit display 1 Air intake for dust sensor 9 Child lock lamp (Page 7) Air is taken in from here and the dust sensor detects the dirty state Lit during child lock. of the air. 10 Negative ion mode indicator (Page 7) 2 Clean monitor (Dust)
-
Page 6: Preparation Before Operation
For these cases, discuss with the Daikin dealer. • If other electrical device operate by the remote controller, either sep- arate them from the remote controller or discuss with the Daikin dealer. 2 Remote controller storage ■... - Page 7 3. Install the Titanium apatite photocatalytic filter roll. 4. Install the plasma ionizer in its original configuration. (1) Cut off one piece along the perforation. Titanium apatite Hole photocatalytic filter roll Hole (2) Place the dark colored surface facing up and then correctly insert into the hooks (four) of the plasma ionizer.
-
Page 8: How To Operate
How to Operate 7 When you want to decide a time to stop operation Press the “ ” [OFF TIMER] button. • Each time it is pressed the timer setting switches as shown below. The remaining time will be lit in the “OFF timer setting indicator”. “... -
Page 9: Care And Cleaning
Care and Cleaning 3. Clean the pre-filter. WARNING • After using a vacuum cleaner to remove any dust, clean with water. During maintenance you must stop the oper- • If it is very dirty, use a soft brush or a neutral cleaner to clean then ation and remove the power plug from the dry well in the shade. - Page 10 Care and Cleaning ■ ■ ■ ■ Replacing the Titanium apatite CAUTION photocatalytic filter roll If the front surface and rear surface of the filer are mis- Replace the Titanium apatite photocatalytic filter roll when the “Replace taken, the performance will drop. indicator”...
- Page 11 • Be careful not to snag or cut the ionizing line. If the ionizing line is pole plates. (Wearing rubber gloves is safer.) cut, request the Daikin dealer to replace it. If the unit is operated with the ionizing line cut, there will be no dust collection.
- Page 12 ■ ■ ■ ■ Disposal requirements 2. While pressing the “ ” [Operation switch/Stop] button Your Daikin product is marked with this symbol. This of the main unit point the remote controller at the main means that electrical and electronic products shall not unit and press the “...
-
Page 13: Trouble Shooting
The four airflow rate displays, LL (Quiet), Is there any foreign matter in the air outlet? Remove the foreign matter. For other cases, contact a Daikin dealer. L (Low), M (Standard) and H (High) are flashing at the same time. - Page 14 3P068886-10R M03B106C (0508) HT...