Table of Contents
Advertisement
Quick Links
AD4545 / ML4545
Installation/Operator Manual
WARNING:
For your safety the
information in this manual must be
followed to minimize the risk of fire or
explosion and to prevent property
damage, personal injury or death.
— Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS:
●
Do not try to light any appliance.
●
Do not touch any electrical switch;
do not use any phone in your
building.
●
Clear the room, building or area of
all occupants.
●
Immediately call your gas supplier
from a neighbor's phone. Follow
the gas supplier's instructions.
●
If you cannot reach your gas
supplier, call the fire department.
— Installation and service must be
performed by a qualified installer,
service agency or the gas supplier.
AVERTISSEMENT: Assurez-vous de
bien suivre les instructions données dans
cette notice pour réduire au minimum le
risque d'incendie ou d'explosion ou pour
éviter tout dommage matériel, toute
blessure ou la mort.
—Ne pas entreposer ni utiliser d'essence
ni d'autres vapeurs ou liquides
inflammables à proximité de cet
appareil ou de tout autre appareil.
—QUE FAIRE SI VOUS SENTEZ UNE
ODEUR DE GAZ:
●
Ne pas tenter d'allumer d'appareils.
●
Ne touchez à aucun interrupteur. Ne
pas vous servir des téléphones se
trouvant dans le bâtiment.
●
Évacuez la pièce, le bâtiment ou la
zone.
●
Appelez immédiatement votre
fournisseur de gaz depuis un voisin.
Suivez les instructions du fournisseur.
●
Si vous ne pouvez rejoindre le
fournisseur de gaz, appelez le service
des incendies.
—L'installation et l'entretien doivent être
assurés par un installateur ou un
service d'entretien qualifié ou par le
fournisseur de gaz.
American Dryer Corporation
88 Currant Road
Fall River MA 02720-4781 USA
Telephone: +1 (508) 678-9000 / Fax: +1 (508) 678-9447
e-mail: techsupport@amdry.com
www.adclaundry.com
ADC Part No. 113608 - 13
Advertisement
Table of Contents
Related Manuals for ADC AD4545
Summary of Contents for ADC AD4545
- Page 1 American Dryer Corporation 88 Currant Road Fall River MA 02720-4781 USA Telephone: +1 (508) 678-9000 / Fax: +1 (508) 678-9447 e-mail: techsupport@amdry.com www.adclaundry.com ADC Part No. 113608 - 13...
- Page 2 Replacement parts can be obtained from your reseller or the ADC factory. When ordering replacement parts from the factory, you can FAX your order to ADC at +1 (508) 678-9447 or telephone your order directly to the ADC Parts Department at +1 (508) 678-9000. Please specify the dryer model number and serial number in addition to the description and part number, so that your order is processed accurately and promptly.
-
Page 3: Table Of Contents
WARNING In the State of Massachusetts, the following installation instructions apply: Proposition 65 ■ Installations and repairs must be performed by Use of this product could expose you to substances a qualified or licensed contractor, plumber, or from fuel combustion that contain chemicals gasfitter qualified or licensed by the State of Massachusetts. -
Page 4: Safety Precautions
Safety Precautions ____________________ WARNING WARNING Do not use heat for drying articles that contain plastic, foam, sponge rubber, or similarly textured For your safety, the information in this manual must rubber materials. Drying in a heated tumbler may be followed to minimize the risk of fire or explosion damage plastics or rubber and also may be a fire and to prevent property damage, personal injury, or hazard. - Page 5 The operation of this appliance may affect the operation of other types of gas appliances, which take their air for safe combustion from the same room. If in doubt, consult the NOTES _____________________________________________________ appliance manufacturer(s). Use this dryer only for its intended purpose, drying fabrics. ____________________________________________________________ The “cool down”...
-
Page 6: Specifications
Specifications _______________________________________________________________________ 20.41 kg MAXIMUM CAPACITY 45 lb (DRY WEIGHT) PER POCKET TUMBLER DIAMETER 32-3/4” 83.19 cm 76.20 cm TUMBLER DEPTH 30” TUMBLER VOLUME 14.6 cu ft 413.43 L PER POCKET 0.56 kW TUMBLER/DRIVE MOTOR 3/4 hp PER POCKET BLOWER/FAN MOTOR BLOWER DRIVEN BY TUMBLER MOTOR PER POCKET 68.6 cm... - Page 7 Specifications _______________________________________________________________________ NOTE: The manufacturer reserves the right to make changes in specifications at any time without notice or obligation. 113608 - 13 www.adclaundry.com...
-
Page 8: Installation Procedures
Installation Procedures _______________ Unpacking / Setting Up ________________ Installation should be performed by competent professional Remove protective shipping material (i.e., plastic wrap and in accordance with local, state, and country codes. In the optional shipping box) from the dryer. absence of these codes, the installation must conform to applicable American National Standards: ANSI Z223.1- IMPORTANT: Dryer must be transported and handled in an upright position at all times. -
Page 9: Fresh Air Supply Requirements
Fresh Air Supply Requirements _______ Exhaust Requirements ________________ This appliance may only be installed in a room that meets Exhaust ductwork should be designed and installed by a the appropriate ventilation requirements specified in the qualified professional. Improperly sized ductwork will create national installation regulations. - Page 10 Outside Ductwork Protection To protect the outside end of the horizontal ductwork from the weather, a 90° elbow bent downward should be installed where the exhaust exits the building. If the ductwork travels vertically up through the roof, it should be protected from the weather by using a 180°...
-
Page 11: Electrical Information
Electrical Information _________________ The illustration below shows the minimum cross-sectional area for multiple dryer round or square venting. These figures Electrical Requirements must be increased if the main duct run from the last dryer to where it exhausts to the outdoors is longer than 20 feet (6.09 All electrical connections must be made by a properly licensed meters) or has more than 1 elbow in it. -
Page 12: Gas Information
Electrical Service Specifications Single-Phase (1ø) Wiring Connections / Hookup ELECTRICAL SERVICE SPECIFICATIONS (PER POCKET) The electrical input connections are made into the rear service IMPORTANT: 208 VAC AND 230/240 VAC ARE NOT THE SAME. When ordering, box located at the top rear of the dryer. The ground specify exact voltage. - Page 13 IMPORTANT: Failure to isolate or disconnect the dryer from Installer within Australia – refer to AS/NZS5601.1 for guidance supply as noted can cause irreparable damage to the gas on gas supply pipe sizing required for this appliance valve, voiding the warranty. installation.
- Page 14 Heat Input / Gas Consumption / Orifice (Injector) Data GAS SPECIFICATIONS FOR DRYERS GOING TO CE COUNTRIES** Orifice Nominal Supply Burner Gross Heat Input Orifice Size Fuel (Injector) Heating Value Pressure*** Per Pocket Pressure Type Consumption Quantity B tu /ft Btu/hr Per Pocket Natural (I...
-
Page 15: Water Information
Water Information _____________________ Optional Manual Bypass Before You Start Provisions are made in the dryer’s fire suppression system Check Local Codes and Permits for the installation of an optional manual bypass. The connections for the manual bypass are made at the “cross” Call your local water company or the proper municipal or “four way”... -
Page 16: Preoperational Test
Preoperational Instructions __________ • Rotate the tumbler (drum) by hand to be sure it moves freely. IMPORTANT: For more detailed information regarding the • Check bolts, nuts, screws, terminals, and fittings for microprocessor controller (computer), refer to the tightness and security. microprocessor user’s manual included with the dryer. -
Page 17: Service / Parts Information
NOTE: Be sure to include the installation date when by the sender. returning the warranty card(s). Shipping charges are not the responsibility of ADC. All returns Warranty should be “prepaid” to the factory. Any “C.O.D.” or “COLLECT” returns will not be accepted. -
Page 18: Routine Maintenance
Routine Maintenance _________________ Every 6 Months Cleaning Inspect and remove lint accumulation in customer furnished exhaust ductwork system and from dryer’s internal exhaust A program and/or schedule should be established for periodic ducting. inspection, cleaning, and removal of lint from various areas of the dryer, as well as throughout the ductwork system. -
Page 19: Data Label Information
Data Label Information ________________ CE Label Standard Label AGA Label When contacting ADC, the information on the data label is required to ensure proper service/parts assistance. The data label is located at the upper left rear of the dryer behind the back guard. -
Page 20: Non-Coin Programming
Non-Coin Programming _______________ SAIL SWITCH OPEN FAULT – Sail switch remained open after the cycle started. Should have closed. BURNER HIGH LIMIT FAULT – Burner temp. disk has opened. BURNER IGNITION CONTROL – No signal to gas valve from (DSI) module during trial for ignition time. DSI module is bad. -
Page 21: Coin Programming
Coin Programming ____________________ Accessing and Clearing Coin Vault Total Enter program mode by switching program switch (up) while Enter Programming Mode By Placing no cycle is in progress. The Programming Switch On The Phase 7 Board Up While No Cycle Is In Progress. Press HI –... - Page 22 ADC Part No. 113608 13 - 12/12/16...