Related Manuals for xDEEP NX ZEN
Summary of Contents for xDEEP NX ZEN
- Page 1 ENGLISH USER MANUAL READ CAREFULLY. YOUR COMFORT AND SAFETY IS WORTH MORE THAN 15 MINUTES.
- Page 2 INDEX INTRODUCTION CE CERTIFICATION SAFETY RULES CONGRATULATIONS! PARTS OF ZEN SYSTEM OPTIONAL DROPPABLE WEIGHT POCKETS YOU HAVE PURCHASED A PERFECT PRODUCT IN WHICH, WITHOUT ANY OPTIONAL TRIM POCKETS COMPROMISE, WE HAVE CONNECTED THE BEST EXISTING MATERIALS MADE IN EUROPE AND IN THE USA, WITH BOTH OUR TECHNICAL ADJUSTING AND RECREATIONAL DIVING EXPERIENCE.
- Page 3 INTRODUCTION...
- Page 4 DANGEROUS PRACTICES. if any information label placed on the Buoyancy Compen- sation Device is not clear, contact the manufacturer for explanation: XDEEP Spółka z ograniczoną odpowiedzialnością Sp. k. Ul.Ogrodników 3, 43-227 Góra Poland Phone: +48 12 44 66 998 e-mail: biuro@xdeep.pl...
- Page 5 CE CERTIFICATION...
-
Page 6: Safety Rules
CE CERTIFICATION SAFETY RULES The products described in the following instruction have ZEN buoyancy compensators has been certified as com- been a subject of certification in a recognized unit and patible with 89/686/EWG directive, as far as it contains meet the requirements of 89/686/EWG directive and of air compatible with EN 12021 norm. - Page 7 Such practice may result in irreparable damage to the BC. any contaminants may trigger rapid growth of ice crystals XDEEP BCDS ARE DESIGNED TO PROVIDE THE USER WITH SAFETY AND COMFORT. IMPROPER USE MAY inside the inflation valve causing the valve freeze.
- Page 8 PARTS OF ZEN SYSTEM...
- Page 9 PARTS OF ZEN SYSTEM ZEN system consists of three basic k-type Power Inflator elements: A K-type inflator is a reliable device made of shock-proof technopolymer which is resistant to environmental condi- tions. The inflator valve is made of metal, which makes the inflator more resistant to freezing and it can be oper- Double shell ZEN BCD;...
- Page 10 OPTIONAL DROPPABLE WEIGHT POCkETS...
- Page 11 ZEN system enables to install, on the waist strap, In order to install the pockets: XDEEP two-part weight pockets of 2 x 3kg or 2 x 6kg. The pockets are mounted with bolts to the holes Remove the buckle and, if necessary, other elements in the backplate: from the waist strap (if installed);...
- Page 12 OPTIONAL TRIM POCkETS ADjUSTING Although ZEN system provides perfect trim in most of Trim pockets of STEALTH 2.0 sidemount system which the suits, in some cases (e.g. dry suit with very thick can be placed anywhere on the crotch strap – useful in undersuit) you may need to have the weight distributed case you are turned upside down: in a special manner.
- Page 13 ADjUSTING When you order a complete buoyancy set, you’re going to In order to lengthen the shoulder or crotch strap, first In the basic version of harness the shoulder straps and In the harness with quick-adjustment buckle you adjust receive all parts assembled and ready to use. However, to insert the end of the webbing into the blocking buckle the crotch strap are adjusted through shortening or the strap by pulling loose ends of the shoulder straps...
- Page 14 ADjUSTING CONT. CONNECTING THE SCUBA TANk Guidelines for how to adjust NX Series harness: In properly adjusted NX Series harness the waist strap should be placed few centimetres below the waist(you need to properly adjust the height at which the plate is installed as well as the length of shoulder straps).
- Page 15 CONNECTING THE SCUBA TANk DANGER STEP 03 STEP 04 AN INCORRECTLY CONNECTED TANk MAY UNEXPECTEDLY DETACH FROM THE HARNESS. SUCH SITUATION IS EXTREMELY DANGEROUS AND MAY RESULT IN A SERIOUS ACCIDENT OR EVEN DEATH. THEREFORE THE TANk CONNECTION HAS TO BE INSPECTED CLOSELY. Attention: ZEN buoyancy compensator is designed to be used with tanks of parameters indicated in technical specification...
- Page 16 CONNECTING THE LP HOSE...
-
Page 17: Pre-Dive Inspection
CONNECTING THE LP HOSE PRE-DIVE INSPECTION To allow for proper operation of the inflator it must be connected to the LP port of the 1st stage of the regulator using the LP hose supplied with the BC. DANGER WARNING LP HOSE CONNECTION USING THE 1ST STAGE OF THE INFLATOR SUPPLY PRESSURE VALUE SHO- THE REGULATOR MUST BE MADE TO THE LOW ULD BE BETWEEN 6 AND 15 BAR. -
Page 18: Operation
If it is not, do not use it until the defect is its elements are working correctly. removed by an authorized XDEEP service center. Check that no element of the BC show any signs of wear, During descent, stop at three meters at the most and... -
Page 19: Post-Dive Maintenance
OPERATION POST-DIVE MAINTENANCE Buoyancy on the surface Ascent In order to ensure maximum buoyancy on the surface, Ascending too quickly may result in decompression before getting into the water (or directly afterascending) sickness. Therefore you must control the rate of ascent inflate the BC using inflator button. -
Page 20: Repair And Maintenance
POST-DIVE MAINTENANCE REPAIR AND MAINTENANCE Disconnecting Drying After diving, take out the weight from the weight pockets After every use, you should dry the BC thoroughly. When (if applicable), disconnect the LP hose from the inflator, drying, the BC should be fully inflated and hung in a dry, and then disconnect the tank. -
Page 21: Specification
REPAIR AND MAINTENANCE SPECIFICATION XDEEP BCDs does not contain any elements which can be repaired by the user, and so all repairs (including lubrica- tion or replacement of worn-out elements) should be performed only by trained technicians holding certificates issued by the producer (authorized service center). - Page 22 SPECIFICATION Inflator Type K-type Basic parameters From 6 bar to 17.23 bar (250 PSI) Working pressure range Type Double shell toroidal type BCD 190 N Buoyancy Permisible tank parameters Type Single tank Outer shell fabric Cordura 1100 dTEX 18 L Size Bladder fabric Nylon 440 dTEX...
- Page 23 USER MANUAL REVISION 15.01.2016 © 2016 XDEEP, All rights reserved.
Need help?
Do you have a question about the NX ZEN and is the answer not in the manual?
Questions and answers