Subscribe to Our Youtube Channel
Related Manuals for xDEEP NX Series
Summary of Contents for xDEEP NX Series
- Page 1 PROJECT ENGLISH USER MANUAL READ CAREFULLY. YOUR COMFORT AND SAFETY IS WORTH MORE THAN 15 MINUTES.
- Page 2 INDEX INTRODUCTION CE CERTIFICATION SAFETY RULES CONGRATULATIONS! PARTS OF PROJECT SYSTEM ADJUSTING YOU HAVE PURCHASED A PERFECT PRODUCT IN WHICH, WITHOUT ANY CONNECTING THE SCUBA TANK COMPROMISE, WE HAVE CONNECTED THE BEST EXISTING MATERIALS MADE IN EUROPE AND IN THE USA, WITH BOTH OUR TECHNICAL CONNECTING THE LP HOSE AND RECREATIONAL DIVING EXPERIENCE.
- Page 3 INTRODUCTION...
- Page 4 DANGEROUS PRACTICES. if any information label placed on the Buoyancy Compen- sation Device is not clear, contact the manufacturer for explanation: XDEEP Spółka z ograniczoną odpowiedzialnością Sp. k. Ul.Ogrodników 3, 43-227 Góra Poland Phone: +48 12 44 66 998 e-mail: biuro@xdeep.pl...
- Page 5 CE CERTIFICATION...
-
Page 6: Safety Rules
CE certifica- The compliance assessment of PROJECT compensator tion with gas mixtures with oxygen level higher than 21% and NX Series diving harness was performed by: (+/- 2%) as stated in 89/686/EWG directive. Polski Rejestr Statków S.A., Recognised certification unit nr 1463 Al.Gen.Józefa Hallera 126... - Page 7 Such practice may result in irreparable damage to the BC. any contaminants may trigger rapid growth of ice crystals XDEEP BCDS ARE DESIGNED TO PROVIDE THE USER WITH SAFETY AND COMFORT. IMPROPER USE MAY inside the inflation valve causing the valve freeze.
- Page 8 PARTS OF PROJECT SYSTEM...
- Page 9 The inflator is equipped with an inflator button (1) to NX Series diving harness of M or XL size, in simple or inflate the BC with air, a purge button (2) to deflate the BC easy-to-unfasten version;...
- Page 10 ADJUSTING...
- Page 11 NX Series harness is available in two sizes: M and XL. loop into the blocking buckle and then take out the excess plate is installed as well as the length of shoulder straps).
- Page 12 CONNECTING THE SCUBA TANk...
- Page 13 CONNECTING THE SCUBA TANk CONNECTING THE LP HOSE DANGER AN INCORRECTLY CONNECTED TANk MAY UNEXPECTEDLY DETACH FROM THE HARNESS. SUCH SITUATION IS EXTREMELY DANGEROUS AND MAY RESULT IN A SERIOUS ACCIDENT OR EVEN DEATH. THEREFORE THE TANk CONNECTION HAS TO BE INSPECTED CLOSELY. Attention: PROJECT buoyancy compensator is designed to be used WARNING...
-
Page 14: Pre-Dive Inspection
CONNECTING THE LP HOSE PRE-DIVE INSPECTION To allow for proper operation of the inflator it must be connected to the LP port of the 1st stage of the regulator using the LP hose supplied with the BC. DANGER WARNING LP HOSE CONNECTION USING THE 1ST STAGE OF THE INFLATOR SUPPLY PRESSURE VALUE SHO- THE REGULATOR MUST BE MADE TO THE LOW ULD BE BETWEEN 6 AND 15 BAR. -
Page 15: Operation
If it is not, do not use it until the defect is its elements are working correctly. removed by an authorized XDEEP service center. Check that no element of the BC show any signs of wear, During descent, stop at three meters at the most and... -
Page 16: Post-Dive Maintenance
OPERATION POST-DIVE MAINTENANCE Buoyancy on the surface Ascent In order to ensure maximum buoyancy on the surface, Ascending too quickly may result in decompression before getting into the water (or directly afterascending) sickness. Therefore you must control the rate of ascent inflate the BC using inflator button. -
Page 17: Repair And Maintenance
POST-DIVE MAINTENANCE REPAIR AND MAINTENANCE Disconnecting Drying After diving, take out the weight from the weight pockets After every use, you should dry the BC thoroughly. When (if applicable), disconnect the LP hose from the inflator, drying, the BC should be fully inflated and hung in a dry, and then disconnect the tank. -
Page 18: Specification
REPAIR AND MAINTENANCE SPECIFICATION XDEEP BCDs does not contain any elements which can be repaired by the user, and so all repairs (including lubrica- tion or replacement of worn-out elements) should be performed only by trained technicians holding certificates issued by the producer (authorized service center). - Page 19 SPECIFICATION Inflator Type K-type Basic parameters From 6 bar to 17.23 bar (250 PSI) Working pressure range Type Double shell toroidal type BCD with the NX Seriess harness 230 N Permisible tank parameters Buoyancy Type Double tank set (twinset) Outer shell fabric Cordura 1100 dTEX 2x 18 L Size...
- Page 20 PROJECT USER MANUAL REVISION 25.06.2016 © 2016 XDEEP, All rights reserved.
Need help?
Do you have a question about the NX Series and is the answer not in the manual?
Questions and answers