Summary of Contents for Diginet LEDsmart+ MultiMate MMTM/PB
- Page 1 Setup Functions Guide MMTM/PB Push Button Minute Timer Programmable between 1 minute and 30 minutes with built in multi-way control www.glg.lighting...
-
Page 2: Timer Setup
Push Button Minute Timer Timer Setup The LEDsmart push button timer has a number of useful functions which can easily be set up by entering setup mode and following the four easy steps. The TIMEOUT PERIOD should always be set up. The other settings are optional, depending on the application. To set the timeout period now, go to the next page. - Page 3 Push Button Minute Timer A1: Timer has been powered up via mains 240Vac for LESS THAN 15 MINUTES Step 1 Press and hold the button for 10 seconds Note: Connected lights will dim up or down, this is normal Step 2 The white LED Indicators will blink ON/OFF twice per second.
- Page 4 Push Button Minute Timer B: Setting the Timeout Interval The Minutes timer allows a timeout duration of between 1 to 30 minutes in increments of 1 minute. Out of the box (factory defaults), the time out interval is set to 15 minutes. To change the time out interval from the default 15 minutes, follow the steps below.
- Page 5 Push Button Minute Timer C: Setting Maximum Brightness The maximum brightness level provided by the timer can be set to suit customer requirements. Note that when lamps are near to full brightness, it is difficult to see changes in dimming level. Therefore, when setting up maximum brightness, it is recommended that the lamp is slowly dimmed up to a point where no further changes in brightness can be seen, and the maximum level set at this point.
- Page 6 Push Button Minute Timer D: Setting Advanced Timer Mode The advanced timer mode provides an optional advanced warning to the user that the lights will shortly turn off automatically. When the advance timer is enabled, at time out the lights are dimmed to 50% over a 4 second period and are held at this 50% level for 5 minutes.
- Page 7 Push Button Minute Timer E: Setting Off State Indication When the timer is switched off, the white LED indicators in the timer can be set to glow or turn off. By Default, the white LED indicators are set to glow when the timer is turned off. To set the LED indicators to turn off when the timer is off, follow the steps below.
- Page 8 Push Button Minute Timer F: Convert Minute to Hour Timer If required, this minute timer can be converted to a standard LEDsmart hour timer, with a time out settable between ¼ hour and 7½ hours, in ¼ hour increments. To convert to an hour timer, follow the steps below. Step 1 Enter into the timer Setup Mode - See PART A Step 2...
- Page 9 Push Button Minute Timer G: Setting Multimate™ Mode Step 1 Enter into the timer Setup Mode - See PART A Step 2 Click the push button 8 times Step 3 LED will blink 8 times If the MultiMate™ function is currently Disabled, lamp(s) connected to the dimmer will now turn OFF b.
- Page 10 Push Button Minute Timer H: Resetting to Factory Default Step 1 Enter into the timer Setup Mode - See PART A Step 2 Click the push button 10 times Step 3 The timer will automatically exit Setup Mode once reset...
- Page 11 ABN 94 122 520 307 96- - 112 Gow Street Padstow NSW 2211 Contact General Enquiries & Aftersales: 1300 799 300 or sales@pierlite.com.au 1300 789 300 Fax: Diginet is a brand of the Gerard Lighting Group Version: Issue 1 July 2020...
-
Page 12: Troubleshooting
LEDsmart+ / MultiMate™ Troubleshooting Guide INTRODUCTION LEDsmart+ dimmers, timers, switches and occupancy sensors include MultiMate™ technology. These devices have revolutionised multiple point control of lighting whilst using conventional wiring practices. Even when not used for multi-way control, their superior compatibility with LED lighting loads makes them the best wall plate lighting controls in the market. - Page 13 LEDsmart+ / MultiMate™ Troubleshooting Guide FLICKERING OR FLASHING WHEN OFF OR AT LOW DIMMING LEVELS Modern LED lighting has revolutionised high brightness low power lighting. Unfortunately, some LED loads can have problems with dimmer compatibility. This can be observed when lamps flicker or flash when set to low dimming levels or when a MultiMate™...
- Page 14 LEDsmart+ / MultiMate™ Troubleshooting Guide CROSSTALK Crosstalk happens when several MultiMate™ circuits are installed in the same building, and adjustments on one circuit cause interference on another circuit. The interference may be observed as: Lighting changes on one circuit cause lighting changes (on / off / change of level) on some other circuit;...
- Page 15 LEDsmart+ / MultiMate™ Troubleshooting Guide FANS, FLUORESCENT LIGHTING AND NON-DIMMABLE LOADS MultiMate™ dimmers, timers, switches and occupancy sensors are designed to control dimmable lighting loads. Sometimes these products need to control non-dimmable loads, for example fluorescent lighting, non- dimmable LED lamps, or bathroom exhaust fans. Direct wiring of these loads to MultiMate™...