TL-R1200C-RP User Guide 1. Preface About This Guide This guide provides information on the QNAP TL-R1200C-RP JBOD enclosure and step-by-step instructions on installing the hardware. It also provides instructions on basic operations and troubleshooting information. Audience This document is intended for consumers and storage administrators. This guide assumes that the user has a basic understanding of storage and backup concepts.
This chapter provides basic information about the QNAP JBOD Expansion Unit JBOD enclosure. About the TL-R1200C-RP QNAP JBOD enclosures are designed to increase the capacity and utility of your NAS or computer and provide a wide range of storage applications. Drives installed in the JBOD enclosure can be managed independently or be configured as software RAID by the host device.
Page 6
• Information on rail kit installation can be found in the installation guide included in the rail kit package. Power supply unit TL-R1200C-RP: 2 x 250W, 100 - 240V AC, 50/60 Hz Warning To reduce the risk of fire or electric shock, ensure that you only connect the power cord to a properly grounded electrical outlet.
TL-R1200C-RP User Guide Model specifications are subject to change without prior notice. To see the latest specifications, go to https://www.qnap.com. Package Contents Item Quantity TL-R1200C-RP Power cord USB 3.1 Gen 2 Type-C to USB Type-A connector cable Screws for 3.5-inch drives Screws for 2.5-inch drives...
TL-R1200C-RP User Guide Rear Panel Component Component Power supply unit 1 USB 3.1 Gen 2 Type-C port Power supply unit 2 Fan speed switch Audio alert switch USB cable clip slot Power switch Drive Numbering Product Overview...
TL-R1200C-RP User Guide Safety Information The following instructions help ensure personal safety and environmental safety. Read these instructions carefully before performing any operations. General Instructions • The NAS should be stored in a secure location with restricted access, controlled through the use of a tool, lock and key, or any means of security.
TL-R1200C-RP User Guide Installation Requirements Category Item Environment • Room temperature: 0˚C to 40˚C (32˚F to 104˚F) • Non-condensing relative humidity: 5% to 95% • Wet-bulb temperature: 27˚C (80.6˚F) • Flat, anti-static surface without exposure to direct sunlight, liquids, or chemicals Hardware and peripherals •...
3. Hardware Installation This section provides information on installing drives, memory modules, and expansion cards. Drive Installation QNAP JBOD enclosures are compatible with 3.5-inch hard drives, 2.5-inch hard drives, and 2.5-inch solid- state drives. Installing 3.5-inch Drives on 3.5-inch Trays Warning •...
Page 12
Place the drive on the tray so that the holes on the bottom of the drive are aligned with the holes on the bottom of the tray. b. Attach the screws to further secure the drive. Important QNAP recommends attaching the screws to the drive trays when transporting the device. Hardware Installation...
The JBOD enclosure may take up to 30 seconds to detect the new drive. Installing 2.5-inch Drives on 3.5-inch Trays For the list of compatible drive models, go to https://www.qnap.com/compatibility. Warning • Installing a drive deletes all data on the drive.
Page 14
TL-R1200C-RP User Guide 2. Remove a drive tray. a. Pull the handle to release the tray. b. Pull the tray out. 3. Install a drive on the tray. a. Place the drive on the tray so that the holes on the bottom of the drive are aligned with the holes on the bottom of the tray.
Page 15
TL-R1200C-RP User Guide 4. Load the tray into the bay. a. Insert the tray into the bay. b. Push the handle. 5. Power on the JBOD enclosure. Note The JBOD enclosure may take up to 30 seconds to detect the new drive.
• Do not connect the JBOD enclosure to a host device using a USB hub. • Boot failures may occur when disconnecting and reconnecting the external device from the host device repeatedly within a short time. QNAP recommends waiting 10 seconds before reconnecting the external device to the host device.
Connecting the JBOD Enclosure to a Computer Important • QNAP JBOD enclosures cannot be connected to more than one host at a time. • QNAP JBOD enclosures do not support USB 2.0 connections. • Depending on the number of installed drives, the JBOD enclosure may consume more USB endpoints than the host device can support on a single USB connection.
5. Power on the computer. 6. Verify that the JBOD enclosure is recognized by the computer. a. Go to your computer's disk management utility or open QNAP JBOD Manager in Windows or Ubuntu. b. Verify that the JBOD enclosure is listed.
Page 19
TL-R1200C-RP User Guide 2. Insert the cable into the clip. 3. Close the clip to secure the cable. Hardware Installation...
TL-R1200C-RP User Guide Removing a USB Cable from the USB Cable Clip 1. Open the cable clip. 2. Remove the cable from the clip. Hardware Installation...
TL-R1200C-RP User Guide Hot-Swapping Redundant Power Supply Units JBOD enclosures with redundant power supply units (PSUs) support hot-swapping. Warning The NAS may have one or more power supply unit (PSU) cords. To avoid serious injuries, a trained service technician must disconnect all PSU cords before installing or replacing system components.
5. Connect the power cord to the PSU and the electrical outlet. 6. Power on the JBOD enclosure. Rail Kits The TL-R1200C-RP is compatible with the following models: • RAIL-B02 Rail kits are not included with the JBOD enclosure and must be purchased separately. For details, contact an authorized reseller or go to http://shop.qnap.com.
Page 23
TL-R1200C-RP User Guide Hardware Installation...
A drive read/write error occured. Note The drive LEDs only function when connected to a NAS or computer running QTS, QTS hero, or QNAP JBOD Manager. Audio Alert Note The audio alert can be toggled on and off by using the audio alert switch on the rear panel of the JBOD enclosure.
TL-R1200C-RP User Guide Duration Frequency Description Long beep (2 seconds) 3 (every 5 • The system fan is not functioning. minutes) • The system temperature is over the threshold. Note • The default temperature warning threshold is 65°C. You can set the threshold to a temperature between 55°C and 69°C using...
Forcing Storage & Snapshots or QNAP JBOD Manager to Recognize the JBOD Enclosure If Storage & Snapshots or QNAP JBOD Manager is unable to locate the JBOD enclosure during operation, the drives or data may be faulty. 1. Power off the JBOD enclosure.
11. Go to Main Menu > Storage & Snapshots > Storage > Storage/Snapshots . 12. Locate the volume that contains the new drive and then verify that the status is Rebuilding. Support and Other Resources QNAP provides the following resources: Resource Documentation https://docs.qnap.com...
QNAP JBOD Manager Software utility for Windows, Linux, and macOS that allows you to view and configure QNAP JBOD enclosures Storage & Snapshots QTS utility that allows you to view and configure QNAP JBOD enclosures connected to a QNAP NAS Glossary...
No license, express or implied, by estoppels or otherwise, to any intellectual property rights is granted by this document. Except as provided in QNAP's terms and conditions of sale for such products, QNAP assumes no liability whatsoever, and QNAP disclaims any express or implied warranty, relating to sale and/or use of QNAP products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right.
Page 30
TL-R1200C-RP User Guide Free Software Foundation, use the GNU General Public License for most of our software; it applies also to any other work released this way by its authors. You can apply it to your programs, too. When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are...
Page 31
TL-R1200C-RP User Guide tells the user that there is no warranty for the work (except to the extent that warranties are provided), that licensees may convey the work under this License, and how to view a copy of this License. If the interface presents a list of user commands or options, such as a menu, a prominent item in the list meets this criterion.
Page 32
TL-R1200C-RP User Guide You may convey verbatim copies of the Program's source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice; keep intact all notices stating that this License and any non-permissive terms added in accord with section 7 apply to the code;...
Page 33
TL-R1200C-RP User Guide the object code. If the place to copy the object code is a network server, the Corresponding Source may be on a different server (operated by you or a third party) that supports equivalent copying facilities, provided you maintain clear directions next to the object code saying where to find the Corresponding Source.
Page 34
TL-R1200C-RP User Guide a. Disclaiming warranty or limiting liability differently from the terms of sections 15 and 16 of this License; or b. Requiring preservation of specified reasonable legal notices or author attributions in that material or in the Appropriate Legal Notices displayed by works containing it; or c.
Page 35
TL-R1200C-RP User Guide An “entity transaction” is a transaction transferring control of an organization, or substantially all assets of one, or subdividing an organization, or merging organizations. If propagation of a covered work results from an entity transaction, each party to that transaction who receives a copy of the work also...
Page 36
TL-R1200C-RP User Guide If conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot convey a covered work so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not convey it at all.
Important Any modifications made to this device that are not approved by QNAP Systems, Inc. may void the authority granted to the user by the FCC to operate this equipment. VCCI Notice この装置は、クラス...