Subscribe to Our Youtube Channel
Related Manuals for Accton Technology Edge-Core ES3528M-SFP
Summary of Contents for Accton Technology Edge-Core ES3528M-SFP
- Page 1 Powered by Accton ES3528M-SFP Installation Guide Fast Ethernet Switch www.edge-core.com...
- Page 3 Installation Guide Fast Ethernet Switch Layer 2 Workgroup Switch with 24 100BASE-BX (SFP) Ports, 2 1000BASE-T (RJ-45) and 2 Combination Gigabit (RJ-45/SFP) Ports...
- Page 4 ES3528M-SFP E012008-DG-R01 150200062000A...
- Page 5 Compliances and Safety Warnings FCC - Class A This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
- Page 6 CE Mark Declaration of Conformance for EMI and Safety (EEC) This information technology equipment complies with the requirements of the Council Directive 89/336/EEC on the Approximation of the laws of the Member States relating to Electromagnetic Compatibility and 73/23/EEC for electrical equipment used within certain voltage limits and the Amendment Directive 93/68/EEC.
- Page 7 Safety Compliance Warning: Fiber Optic Port Safety When using a fiber optic port, never look at the transmit laser while it is powered on. Also, never look directly at the fiber TX port and fiber cable CLASS I LASER DEVICE ends when they are powered on.
- Page 8 Power Cord Set U.S.A. and Canada The cord set must be UL-approved and CSA certified. The minimum specifications for the flexible cord are: - No. 18 AWG - not longer than 2 meters, or 16 AWG. - Type SV or SJ - 3-conductor The cord set must have a rated current capacity of at least 10 A The attachment plug must be an earth-grounding type with NEMA...
- Page 9 France et Pérou uniquement: Ce groupe ne peut pas être alimenté par un dispositif à impédance à la terre. Si vos alimentations sont du type impédance à la terre, ce groupe doit être alimenté par une tension de 230 V (2 P+T) par le biais d’un transformateur d’isolement à rapport 1:1, avec un point secondaire de connexion portant l’appellation Neutre et avec raccordement direct à...
- Page 10 Stromkabel . Dies muss von dem Land, in dem es benutzt wird geprüft werden: Schweiz Dieser Stromstecker muß die SEV/ASE 1011Bestimmungen einhalt- Europe Das Netzkabel muß vom Typ HO3VVF3GO.75 (Mindestanforderung) sein und die Aufschrift <HAR> oder <BASEC> tragen. Der Netzstecker muß die Norm CEE 7/7 erfüllen (”SCHUKO”). Warnings and Cautionary Messages Warning: This product does not contain any serviceable user parts.
- Page 11 Environmental Statement The manufacturer of this product endeavours to sustain an environmentally-friendly policy throughout the entire production process. This is achieved though the following means: • Adherence to national legislation and regulations on environmental production standards. • Conservation of operational resources. •...
- Page 12 About This Guide Purpose This guide details the hardware features of this device, including the physical and performance-related characteristics, and how to install it. Audience The guide is intended for use by network administrators who are responsible for installing and setting up network equipment; consequently, it assumes a basic working knowledge of LANs (Local Area Networks).
-
Page 13: Table Of Contents
Contents Chapter 1: Introduction Overview Switch Architecture Network Management Options Description of Hardware SFP Slots Console Port Port and System Status LEDs Power Supply Sockets Features and Benefits Connectivity Expandability Performance Management Chapter 2: Network Planning Introduction to Switching Application Examples Collapsed Backbone Network Aggregation Plan Remote Connection with Fiber Cable... - Page 14 Contents Chapter 4: Making Network Connections Connecting Network Devices Twisted-Pair Devices Cabling Guidelines Connecting to PCs, Servers, Hubs and Switches Network Wiring Connections Fiber Optic SFP Devices Connectivity Rules 1000BASE-T Cable Requirements 1000 Mbps Gigabit Ethernet Collision Domain 100 Mbps Fast Ethernet Collision Domain 10 Mbps Ethernet Collision Domain Cable Labeling and Connection Records Appendix A: Troubleshooting...
- Page 15 Contents Glossary Index...
- Page 16 Contents...
- Page 17 Tables Table 1-1 ES3528M-SFP Port Status LEDs Table 1-2 System Status LEDs Table 3-1 Serial Cable Wiring Table 4-1. Maximum 1000BASE-T Gigabit Ethernet Cable Length Table 4-2. Maximum 1000BASE-SX Gigabit Ethernet Cable Length Table 4-3. Maximum 1000BASE-LX Gigabit Ethernet Cable Length Table 4-4.
- Page 18 Figures Figure 1-1. ES3528M-SFP Front and Rear Panels Figure 1-2. ES3528M-SFP Port Status LEDs Figure 1-3. ES3528M System Status LED Figure 1-4. Power Supply Sockets Figure 2-1. Collapsed Backbone Figure 2-2. Network Aggregation Plan Figure 2-3. Remote Connection with Fiber Cable Figure 2-4.
-
Page 19: Chapter 1: Introduction
Chapter 1: Introduction Overview The ES3528M-SFP is an intelligent switch with 24 100BASE SFP transceiver slots, two Gigabit combination ports that are comprised of a RJ-45 port and an SFP transceiver slot and 2 Gigabit stacking ports. There is also an SNMP-based management agent embedded on the main board. -
Page 20: Switch Architecture
Introduction Switch Architecture The ES3528M-SFP switch employs a wire-speed, non-blocking switching fabric. This permits simultaneous wire-speed transport of multiple packets at low latency on all ports. This switch also features full-duplex capability on all ports, which effectively doubles the bandwidth of each connection. his switch uses store-and-forward switching to ensure maximum data integrity. -
Page 21: Port And System Status Leds
Description of Hardware Port and System Status LEDs The LEDs, which are located on the front panel for easy viewing, are shown below and described in the following table. Port Status LEDs Combination Gigabit Port Status LEDs Figure 1-2. ES3528M-SFP Port Status LEDs Table 1-1 ES3528M-SFP Port Status LEDs Condition Status... -
Page 22: Table 1-2 System Status Leds
Introduction System Status LEDs Figure 1-3. ES3528M System Status LED Table 1-2 System Status LEDs Condition Status On Green Internal power is operating normally. (Power) On Amber Internal power supply has failed. Power off or failure. On Green The backup power supply is operating normally. On Yellow The backup power supply is plugged in but faulty, such as a thermal or fan failure. -
Page 23: Power Supply Sockets
Features and Benefits Power Supply Sockets There is one standard power socket on the rear panel of each switch for the AC power cord. Backup Power Supply Power Socket B PS 1 0 0 /1 1 5/ 22 0 /2 3 0 V 1 .0 /1 .0 /0 .5 /0 .5 A DC IN 5 0 /6 0 HZ... -
Page 24: Management
Introduction Management • “At-a-glance” LEDs for easy troubleshooting • Network management agent: • Manages switch in-band or out-of-band • Supports Telnet, SNMP/RMON and Web-based interface... -
Page 25: Chapter 2: Network Planning
Chapter 2: Network Planning Introduction to Switching A network switch allows simultaneous transmission of multiple packets via non-crossbar switching. This means that it can partition a network more efficiently than bridges or routers. The switch has, therefore, been recognized as one of the most important building blocks for today’s networking technology. -
Page 26: Application Examples
Network Planning Application Examples The ES3528M-SFP is not only designed to segment your network, but also to provide a wide range of options in setting up network connections. Some typical applications are described in the following pages. Collapsed Backbone The ES3528M-SFP is an excellent choice for mixed Ethernet, Fast Ethernet, and Gigabit Ethernet installations where significant growth is expected in the near future. -
Page 27: Network Aggregation Plan
Application Examples Network Aggregation Plan With 24 parallel bridging ports (i.e., 24 distinct collision domains), the switch can collapse a complex network down into a single efficient bridged node, increasing overall bandwidth and throughput. In the figure below, the SFP ports on the switch are providing 100 Mbps connectivity through layer 2 switches. -
Page 28: Remote Connection With Fiber Cable
Network Planning Remote Connection with Fiber Cable Fiber optic technology allows for longer cabling than any other media type. A 1000BASE-SX (MMF) link can connect to a site up to 550 meters away, a 1000BASE-LX (SMF) link up to 5 km, and a 1000BASE-LH link up to 70 km. This allows the switch to serve as a collapsed backbone, providing direct connectivity for a widespread LAN. -
Page 29: Making Vlan Connections
Application Examples Making VLAN Connections The ES3528M-SFP supports VLANs which can be used to organize any group of network nodes into separate broadcast domains. VLANs confine broadcast traffic to the originating group, and can eliminate broadcast storms in large networks. This provides a more secure and cleaner network environment. -
Page 30: Application Notes
Network Planning Application Notes Full-duplex operation only applies to point-to-point access (such as when a switch is attached to a workstation, server or another switch). When the switch is connected to a hub, both devices must operate in half-duplex mode. Avoid using flow control on a port connected to a hub unless it is actually required to solve a problem. -
Page 31: Chapter 3: Installing The Switch
Chapter 3: Installing the Switch Selecting a Site Switch units can be mounted in a standard 19-inch equipment rack or on a flat surface. Be sure to follow the guidelines below when choosing a location. • The site should: • be at the center of all the devices you want to link and near a power outlet. •... -
Page 32: Optional Rack-Mounting Equipment
Installing the Switch Optional Rack-Mounting Equipment If you plan to rack-mount the switch, be sure to have the following equipment available: • Four mounting screws for each device you plan to install in a rack—these are not included • A screwdriver (Phillips or flathead, depending on the type of screws used) Mounting The switch units can be mounted in a standard 19-inch equipment rack or on a desktop or shelf. -
Page 33: Desktop Or Shelf Mounting
Mounting Mount the device in the rack, using four rack-mounting screws (not provided). Be sure to secure the lower rack-mounting screws first to prevent the brackets being bent by the weight of the switch. Figure 3-2. Installing the Switch in a Rack If installing a single switch only, turn to “Connecting to a Power Source”... -
Page 34: Installing An Optional Sfp Transceiver
Installing the Switch If installing a single switch only, go to “Connecting to a Power Source” at the end of this chapter. If installing multiple switches, attach four adhesive feet to each one. Place each device squarely on top of the one below, in any order. If also installing an RPS, place it close to the stack. -
Page 35: Connecting To A Power Source
Connecting to a Power Source Connecting to a Power Source To connect a device to a power source: Insert the power cable plug directly into the socket located at the back of the device. B PS 1 0 0 /1 1 5/ 22 0 /2 3 0 V 1 .0 /1 .0 /0 .5 /0 .5 A DC IN 5 0 /6 0 HZ... -
Page 36: Wiring Map For Serial Cable
Installing the Switch Wiring Map for Serial Cable Table 3-1 Serial Cable Wiring Switch’s 8-Pin Null Modem PC’s 9-Pin Serial Port DTE Port 6 RXD (receive data) <---------------------------- 3 TXD (transmit data) 3 TXD (transmit data) -----------------------------> 2 RXD (receive data) 5 SGND (signal ground) ------------------------------ 5 SGND (signal ground) No other pins are used. -
Page 37: Chapter 4: Making Network Connections
Chapter 4: Making Network Connections Connecting Network Devices The ES3528M-SFP is designed to interconnect multiple segments (or collision domains) using optional SFP tranceivers. It can be connected to network cards in PCs and servers, as well as to hubs, switches or routers. Two combination 1000BASE-T/SFP ports provide the uplink connection from the switch to other switches or routers at the central office. -
Page 38: Network Wiring Connections
Making Network Connections If the device is a PC card and the switch is in the wiring closet, attach the other end of the cable segment to a modular wall outlet that is connected to the wiring closet. (See “Network Wiring Connections” on page 4-2.) Otherwise, attach the other end to an available port on the switch. -
Page 39: Fiber Optic Sfp Devices
Fiber Optic SFP Devices Fiber Optic SFP Devices An optional SFP transceiver (100BASE-FX, 100BASE-BX, 1000BASE-SX, 1000BASE-LX, or 1000BASE-LH) can be used for a backbone connection between switches, or for connecting to a server or PC. Each multimode fiber optic port requires 50/125 or 62.5/125 micron multimode fiber optic cabling with an LC connector at both ends. -
Page 40: Connectivity Rules
Making Network Connections The maximum length for fiber optic cable operating at Fast Ethernet speed will depend on the fiber type as listed under “100 Mbps Fast Ethernet Collision Domain” on page 4-5. The maximum length for fiber optic cable operating at Gigabit speed will depend on the fiber type as listed under “1000 Mbps Gigabit Ethernet Collision Domain”... -
Page 41: 100 Mbps Fast Ethernet Collision Domain
Connectivity Rules Table 4-4. Maximum 1000BASE-LH Gigabit Ethernet Cable Length Fiber Size Fiber Bandwidth Maximum Cable Length Connector 9/125 micron 2 m - 70 km (7 ft - 43.5 miles) LC single-mode fiber 100 Mbps Fast Ethernet Collision Domain Table 4-5. Maximum Fast Ethernet Cable Length Type Cable Type Max. -
Page 42: Cable Labeling And Connection Records
Making Network Connections Cable Labeling and Connection Records When planning a network installation, it is essential to label the opposing ends of cables and to record where each cable is connected. Doing so will enable you to easily locate inter-connected devices, isolate faults and change your topology without need for unnecessary time consumption. -
Page 43: Appendix A: Troubleshooting
Appendix A: Troubleshooting Diagnosing Switch Indicators Table A-1. Troubleshooting Chart Symptom Action Pwr LED is Off • Power supply is disconnected. • Check connections between the switch, the power cord, and the wall outlet. • Contact your dealer for assistance. Pwr LED is Amber •... -
Page 44: Power And Cooling Problems
Troubleshooting Power and Cooling Problems If the power indicator does not turn on when the power cord is plugged in, you may have a problem with the power outlet, power cord, or internal power supply. However, if the unit powers off after running for a while, check for loose power connections, power losses or surges at the power outlet, and verify that the fans on the unit are unobstructed and running prior to shutdown. -
Page 45: Appendix B: Cables
Appendix B: Cables Twisted-Pair Cable and Pin Assignments For 10/100BASE-TX connections, a twisted-pair cable must have two pairs of wires. For 1000BASE-T connections the twisted-pair cable must have four pairs of wires. Each wire pair is identified by two different colors. For example, one wire might be green and the other, green with white stripes. -
Page 46: Straight-Through Wiring
Cables Table B-1. 10/100BASE-TX MDI and MDI-X Port Pinouts MDI Signal Name MDI-X Signal Name Transmit Data plus (TD+) Receive Data plus (RD+) Transmit Data minus (TD-) Receive Data minus (RD-) Receive Data plus (RD+) Transmit Data plus (TD+) Receive Data minus (RD-) Transmit Data minus (TD-) Not used Not used... -
Page 47: 1000Base-T Pin Assignments
Twisted-Pair Cable and Pin Assignments 10/100BASE-TX Crossover Cable White/Orange Stripe Orange White/Green Stripe End A End B Blue White/Blue Stripe Green White/Brown Stripe Brown Figure B-3. Crossover Wiring 1000BASE-T Pin Assignments All 1000BASE-T ports support automatic MDI/MDI-X operation, so you can use straight-through cables for all network connections to PCs or servers, or to other switches or hubs. - Page 48 Cables Cable Testing for Existing Category 5 Cable Installed Category 5 cabling must pass tests for Attenuation, Near-End Crosstalk (NEXT), and Far-End Crosstalk (FEXT). This cable testing information is specified in the ANSI/TIA/EIA-TSB-67 standard. Additionally, cables must also pass test parameters for Return Loss and Equal-Level Far-End Crosstalk (ELFEXT).
-
Page 49: Appendix C: Supported Sfp Tranceivers
Appendix C: Supported SFP Tranceivers Note: Power budget constraints must be considered when calculating the maximum cable length for your specific environment. 100BASE-X SFP Transceivers Table C-1. 100BASE-X SFP Transceivers Model Name Wavelength Fiber Distance Transmit Receiver Link (nm) Type Power Sensitivity Budget... -
Page 50: 1000Base-X Sfp Transceivers
Supported SFP Tranceivers 1000BASE-X SFP Transceivers Table C-3. 1000BASE-X SFP Transceivers Model Name Wavelength Fiber Distance Transmit Receiver Link (nm) Type Power Sensitivity Budget (dBm) (dBm) (dBm) ET4201-SX 550 m -9.5~-4 ET4201-LX 1310 10 km -9.5~-3 10.5 ET4201-LHX 1310 40 km -2~3 ET4201-ZX 1550... -
Page 51: Appendix D: Specifications
Appendix D: Specifications Physical Characteristics Ports 24 100BASE-X ports, with auto-negotiation 2 1000BASE-T ports (RJ-45) 2 Combination Gigabit ports (RJ-45/SFP) Network Interface Ports 1-24: SFP (100BASE-FX, 100BASE-BX) Ports 25-28: RJ-45 connector, auto MDI/X 10BASE-T: RJ-45 (100-ohm, UTP cable; Category 3 or better) 100BASE-TX: RJ-45 (100-ohm, UTP cable;... -
Page 52: Switch Features
Specifications Temperature Operating: 0 to 45 °C (32 to 113 °F) Storage: -40 to 70 °C (-40 to 158 °F) Humidity Operating: 10% to 90% (non-condensing) Power Supply Internal, auto-ranging transformer: 100 to 240 V, 50-60 Hz, 1.5 A Power Consumption 30 Watts maximum Maximum Current 0.25 A @ 115 VAC... -
Page 53: Standards
Standards Standards IEEE 802.3-2005 Ethernet, Fast Ethernet, Gigabit Ethernet IEEE 802.1D (Bridging) ISO/IEC 8802-3 Compliances CE Mark Emissions FCC Class A Industry Canada Class A EN55022 (CISPR 22) Class A EN 61000-3-2/3 VCCI Class A C-Tick - AS/NZS 3548 (1995) Class A Immunity EN 61000-4-2/3/4/5/6/8/11 Safety... - Page 54 Specifications...
- Page 55 Glossary 10BASE-T IEEE 802.3 specification for 10 Mbps Ethernet over two pairs of Category 3, 4, or 5 UTP cable. 100BASE-BX IEEE 802.3-2005 specification for 100 Mbps Fast Ethernet over one strand of 9/125 micron core fiber cable. 100BASE-FX IEEE 802.3-2005 specification for 100 Mbps Fast Ethernet over two strands of 9/125, 50/125 or 62.5/125 micron core fiber cable.
- Page 56 Glossary Collision A condition in which packets transmitted over the cable interfere with each other. Their interference makes both signals unintelligible. Collision Domain Single CSMA/CD LAN segment. CSMA/CD CSMA/CD (Carrier Sense Multiple Access/Collision Detect) is the communication method employed by Ethernet, Fast Ethernet, or Gigabit Ethernet. End Station A workstation, server, or other device that does not forward traffic.
- Page 57 Glossary IEEE 802.3u Defines CSMA/CD access method and physical layer specifications for 100BASE-TX Fast Ethernet. (Now incorporated into IEEE 802.3-2005.) IEEE 802.3x Defines Ethernet frame start/stop requests and timers used for flow control on full-duplex links. (Now incorporated into IEEE 802.3-2005.) IEEE 802.3z Defines CSMA/CD access method and physical layer specifications for 1000BASE Gigabit Ethernet.(Now incorporated into IEEE 802.3-2005.)
- Page 58 Glossary Telecommunications Industry Association Transmission Control Protocol/Internet Protocol (TCP/IP) Protocol suite that includes TCP as the primary transport protocol, and IP as the network layer protocol. Unshielded twisted-pair cable. Virtual LAN (VLAN) A Virtual LAN is a collection of network nodes that share the same collision domain regardless of their physical location or connection point in the network.
- Page 59 Index Numerics 10 Mbps connectivity rules 4-5 electrical interference, avoiding 3-1 100 Mbps connectivity rules 4-5 equipment checklist 3-1 1000BASE-T Ethernet connectivity rules 4-5 pin assignments B-3 ports 1-2 100BASE-TX Fast Ethernet connectivity rules 4-5 pin assignments B-1 features D-2 ports 1-2 management 1-6 10BASE-T...
- Page 60 Index Web-based 1-2 pinouts B-3 mounting the switch rubber foot pads, attaching 3-3 in a rack 3-2 on a desktop or shelf 3-3 multimode fiber optic cables 4-3 screws for rack mounting 3-2 site selelction 3-1 SNMP agent 1-2 network specifications connections 4-1 compliances D-3...
- Page 62 ES3528M-SFP E012008-DG-R01 150200062000A...
Need help?
Do you have a question about the Edge-Core ES3528M-SFP and is the answer not in the manual?
Questions and answers