Table of Contents
Advertisement
Quick Links
IMPORTANT -
MANUAL BEFORE INSTALLING UNIT
CAUTION
- Before installation, careful consideration must be given
to how this system will operate if connected to any other piece of
mechanical equipment, i.e. a forced air furnace or air handler, oper-
ating at a higher static. After installation, the compatibility of the two
pieces of equipment must be confirmed by measuring the airflow's of
the Heat / Energy Recovery Ventilators.
It is always important to assess how the operation of any HRV/ERV
may interact with vented combustion equipment (i.e. Gas Furnaces,
Oil Furnaces, Wood Stoves, etc.).
NEVER
- install a ventilator in a situation where its normal opera-
tion, lack of operation or partial failure may result in the backdrafting
or improper functioning of vented combustion equipment!!!
ERV-WI 500
Your ventilation system should be installed in conformance with the appropriate provincial or state
requirements or in the absence of such requirements with the current edition of the National
Building Code, and / or ASHRAE's " good Engineering Practice".
INSTALLATION, OPERATION AND MAINTENANCE MANUAL
All manuals and user guides at all-guides.com
PLEASE READ THIS
Light Commercial
Heat/Energy Recovery Ventilator
HRV-XI 450 or ERV-XI 450
C C
R
R
C
US
1
Advertisement
Table of Contents
Related Manuals for Fantech ERV-WI 500
Summary of Contents for Fantech ERV-WI 500
- Page 1 ERV-WI 500 HRV-XI 450 or ERV-XI 450 Your ventilation system should be installed in conformance with the appropriate provincial or state requirements or in the absence of such requirements with the current edition of the National Building Code, and / or ASHRAE’s “...
-
Page 2: Table Of Contents
5 years on INSTALLATION....................10 parts and 7 years on the motor & the ERV-WI 500 has a warranty that is Mounting the Unit ..................10 limited to 1 year on parts and 7 years Location &... -
Page 3: The Hrv-Xi 450 Heat Recovery
All manuals and user guides at all-guides.com HRV-XI 450 Heat Recovery Ventilator Light Commercial HRV SPECIFICATIONS CASE 20 gauge galvanized steel. Baked powder coated paint, grey. Insulated with 1" (25 mm) foil-face fiberglass insulation to prevent condensation. Two (2) drain connections 1/2" NPT. - Page 4 All manuals and user guides at all-guides.com HRV-XI 450 Light Commercial HRV Dimensions MOUNTING HOLES(1/4-20UNC BOLT) ELECTRICAL BOX (can be relocated in the field to either the front or the back of the cabinet depending on port direction installer chooses) 2.3"...
-
Page 5: Erv-Xi 450
All manuals and user guides at all-guides.com ERV-XI 450 Light Commercial ERV Energy Recovery Ventilator SPECIFICATIONS CASE 20 gauge galvanized steel. Baked powder coated paint, grey. Insulated with 1" (25 mm) foil-face fiberglass insulation to prevent condensation. BLOWERS Two ebm™ direct drive external rotor blowers with forward curved blades. - Page 6 All manuals and user guides at all-guides.com ERV-XI 450 Light Commercial ERV Dimensions Airflow (L/s) 0.85 398.1 0.83 348.3 High 0.81 298.6 0.79 248.8 0.77 * Med-High 199.0 0.75 149.3 0.73 99.5 0.71 49.8 0.69 0.67 Airflow (cfm) * Med-High - Contact Airflow (cfm) Factory for wiring info Airflow...
-
Page 7: Erv-Wi 500
FILTERS Two (2) 2" medium efficiency pleated filters, one (1) per air stream. The ERV-WI 500 is an energy recovery ventilator (ERV) that MOUNTING Unit may be suspended by using the supplied transfers both latent and heat energy. Designed for most... - Page 8 All manuals and user guides at all-guides.com ERV-WI 500 Light Commercial ERV Dimensions (25.70") (8") (50.23") 654mm 203mm 1276mm (30.40") (32.16") (3.24") 772mm 817mm 82mm (18.32") 465.4mm (14") (54.30") (5.90") 149mm 1379mm 355mm (56.30") (17.67") 1429mm 449mm Airflow (L/s) High Speed...
-
Page 9: Operation
(HRV-XI 450 & ERV-XI 450) or by manipulating jumpers in the electrical box. See wiring diagram. The ERV-WI 500 is factory set to high speed. Internal low voltage contacts allow interuption of power to unit when optional remote control is used. -
Page 10: Installation
All manuals and user guides at all-guides.com INSTALLATION LOCATION The HRV/ERV must be located in a heated space where it will be possible to conve- PRACTICAL niently service the unit. Typically the HRV/ERV would be located in the mechanical TIPS room, above a drop ceiling or an area close to the outside wall where the weather- hoods will be mounted. -
Page 11: Location & Ducting
All manuals and user guides at all-guides.com INSTALLING DUCTS GOING TO / FROM OUTSIDE INSTALLING THE DUCTING TO THE WEATHERHOODS OUTSIDE WEATHERHOODS – The weatherhoods must have built-in "bird" screens with 1/4 inch (6.35 mm) minimum mesh to prevent birds and rodents from entering into the ductwork. Do not use smaller mesh as it will be very susceptible to pluging up. - Page 12 In buildings without a forced air HVAC systems, fresh air should be supplied to all habitable areas. It should be sup- plied from high wall or ceiling locations. Grilles that diffuse the air comfortably such as Fantech grille {MGE (metal) or PGE (plastic)}s are recommended.To avoid possible noise transfer through the ductwork system, a piece of flexi-...
- Page 13 • A piece of flexible ducting should be placed between the HRV and the rigid ducting to Push the Fantech grille {MGE (metal) or PGE (plastic)} into the optional mounting absorb any noise or collar or directly into installed elbow. vibrations.
-
Page 14: Examples
All manuals and user guides at all-guides.com INSTALLATION EXAMPLES * Drawings are illustrations only and actual port locations and airflow directions may vary, consult unit spec sheets. It is the responsibility of the installer to ensure all ductwork is sized and installed as designed to ensure the system will perform as intended. - Page 15 All manuals and user guides at all-guides.com INSTALLATION EXAMPLES (CON'T) * Drawings are illustrations only and actual port locations and airflow directions may vary, consult unit spec sheets. It is the responsibility of the installer to ensure all ductwork is sized and installed as designed to ensure the system will perform as intended.
-
Page 16: Air Flow Balancing
All manuals and user guides at all-guides.com AIR FLOW BALANCING • The balancing procedure consists of measuring the exhaust air leaving the system PRACTICAL and the supply air entering the system and ensuring that these two are equal. A TIPS deviation of 10% or less is acceptable. -
Page 17: Maintenance
The drain and drain line - 1. Open ERV-WI 500 access door so that the front or back of the cassette may be easily accessed. Units with drain hoses 2. Support the wheel from the bottom should have their line and 3. -
Page 18: Electrical Connections
All manuals and user guides at all-guides.com WIRING DIAGRAM HRV-XI 450 LIVE TB4-TB6 TB8-TB10 White White TB4-TB6 TB8-TB10 REMOTE (DEFROST) (EXHAUST) (SUPPLY) CONTROL GROUND POWER CORD 120 VAC Blue White Defrost Black Yellow Timer Black CLIX-ON or THERMISTOR 1 (White) 1 (White) 24VAC FOR AQS TB10... - Page 19 All manuals and user guides at all-guides.com WIRING DIAGRAM ERV-WI 500 LINE TB5 & TB6 Internal low voltage contacts for remote control option 24 VAC GROUND TB10 SPEED CONTROL SPEED CONTROL (OPTIONAL) (OPTIONAL) POWER CORD 120 VAC MOTOR WHEEL Brown...
- Page 20 (T) 1.800.407.6195 • (F) 1.800.407.8965 (T) 1.905.696.9235 • (F) 1.905.696.9236 Québec & Atlantic Provinces 50 Kanalflakt Way • Bouctouche, NB, Canada E4S (T) 1.800.565.3548 • (F) 1.877.747.8116 (T) 1.506.743.9500 • (F) 1.506.743.9600 www.fantech.net info@fantech.net Manufactured by: ISO 9001 Article #: 301025 Rev Date: 021203...
Need help?
Do you have a question about the ERV-WI 500 and is the answer not in the manual?
Questions and answers