Advertisement
Installation Instructions
Select angle of opening and use dimensions shown on
Page 4 and Dimension Chart below to locate 4 holes on
stop side of door for closer body (or 4 holes on stop side
of door for 1688 drop plate, only if required, see Page 5),
and 5 holes on stop and/or rabbet for Soffit Plate (or 4
holes on face of transom for 2019L bracket). For
applications not covered in these instructions, a separate
template will be required.
Prepare door and frame for fasteners. See "Preparation
for Fasteners", Page 2.
1601 and 1601BF closers only: Set closer power for
door size using Power Adjustment Chart below. Use 1/8"
hex wrench supplied to adjust Power Adjustment Shaft ...
18 turns maximum. Turn nut CLOCKWISE to Increase,
COUNTER-CLOCKWISE to Decrease power. See Page
6 for the illustration of this step.
Mount 1688 Drop plate ... only if required (see Page 5).
Install closer with "S" and "L" valves away from hinge
edge of door. Note: If using cover, thread in screws
before mounting closer. Leave enough gap between the
head of the screw and the closer to slide the cover on.
Power Adjustment Chart
PARALLEL ARM
DOOR
INSTALLATION
INT
PR1601BF/
CLP1601BF
EXT
INT
PR1601/
CLP1601
EXT
*18 -360° TURNS MAXIMUM AVAILABLE (Door is shipped at mid range)
Dim
in.
A
(mm)
Standard
and
in.
B
Narrow
(mm)
Frame
in.
C
PR1601/
(mm)
PR160XBC
in.
A
(mm)
Flush
in.
B
Partition
(mm)
in.
C
(mm)
in.
A
(mm)
Standard
in.
and
B
Narrow
(mm)
Frame
in.
C
CLP1601/
(mm)
CLP160XBC
in.
A
(mm)
Flush
in.
B
Partition
(mm)
in.
C
(mm)
Copyright © 2003, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
MAXIMUM DOOR SIZE
*
34"
36"
40"
(0.85 m)
(0.9 m)
(1 m)
2
2
3
8
9
RECOMMENDED
USE PR1601/CLP1601
3
5
7
5
7
10
Installation Dimensions Chart
Up to
85°-
90°-
95°-
100°-
85°
90°
95°
100°
105°
9-5/8
(244)
7-5/8
(194)
8-5/8
(219)
9-3/4
(248)
7-5/8
(194)
8-5/8
(219)
11-1/8
8-3/8
10-3/8
9-5/8
9
(283)
(213)
(264)
(244)
(229)
9-1/8
8-3/8
7-5/8
7
6-3/8
(232)
(162)
(213)
(194)
(178)
10-1/8
7-3/8
9-3/8
8-5/8
8
(257)
(238)
(219)
(203)
(187)
11-1/4
8-1/2
10-1/2
9-3/4
9-1/8
(286)
(267)
(248)
(232)
(216)
9-1/8
8-3/8
7-5/8
7
6-3/8
(232)
(162)
(213)
(194)
(178)
10-1/8
9-3/8
8-5/8
8
7-3/8
(257)
(238)
(219)
(203)
(187)
Install Main Arm: Close valves - 'S' and 'L', then turn pinion
shaft more than 50° to permit proper alignment of arm mark
with pinion flat -
See "Main Arm Installation Instructions" below.
Make closer adjustments (see page 6) before installing
cover ... CAUTION: Do not back valves out of closer
completely or a leak will result.
Caution: Closer arm is under spring tension and may
be difficult to rotate.
Reopen valves by turning counter clockwise.
With door closed, align soffit plate with mounting holes in
frame. Fasten soffit plate to frame with oval head screws
provided.... use spacer blocks 2019S or 6891, if required.
If being used, slide the cover over the closer and secure
the mounting screws after the closer has been mounted
and adjusted.
44"
48"
(1.1 m)
(1.2 m)
4
5
NOT
10
13
16
14
105°-
110°-
130°-
110°
130°
180°
8-1/8
6-1/8
(206)
Install arm here
(156)
6-1/8
4-1/8
(see below for
(156)
(105)
7-1/8
5-1/8
(181)
(130)
8-1/4
6-1/4
(210)
(159)
6-1/8
4-1/8
(156)
(105)
7-1/8
5-1/8
Left Hand Door
(181)
(130)
7-3/4
(197)
5-3/4
BC
(146)
Valve
6-3/4
(171)
Left Hand
7-7/8
(200)
5-3/4
(146)
6-3/4
Pinion Flat
(171)
3
'L' for Left hand door.
'R' for Right hand door.
Arm Mounting Detail
Start (wrench) here
Rotate
details)
Typical Installation
"S" and "L"
Stop
Power Adjustment
Screw
(1601 & 1601BF only)
80-9316-2530-020 (05-14)
ASSA ABLOY
Right Hand Door
Stop
BC
Valve
Right Hand
Pinion Flat
Advertisement
