Advertisement
Quick Links
Advertisement
Related Manuals for Barox PD-VDSL-MI100
Summary of Contents for Barox PD-VDSL-MI100
- Page 1 VDSL2 LAN Extender PD-VDSL-MI100 User Manual Version 2.10 March 2021 Page 1...
-
Page 2: Table Of Contents
Table of Contents Chapter 1 Introduction ..........................3 1.1 Features ................................3 1.2 Specification ............................... 4 Chapter 2 Hardware Installation ........................5 2.1 Front Panel ................................. 5 2.2 Rear Panel ................................7 2.3 Installation ................................8 Appendix I ..............................10 Appendix II .............................. -
Page 3: Chapter 1 Introduction
(simply as plug-n-play) and minimum expense by allowing video streaming and data to share the same telephone pair without interference. PD-VDSL-MI100 Ethernet Extender delivers everything needed to quickly deploy a high-speed IP-based network for providing high-speed Internet access, video-on demand services and voice services. The resulting compact, cost- effective form factor offers Systems Integrators, small business owners an attractive Long Reach Ethernet solution. -
Page 4: Specification
1.2 Specification ⚫ 4-position DIP Switch ⚫ LAN Interface: ◼ Selectable CO or CPE mode RJ-45 connector ◼ ◼ Selectable 30a or 17a (VDSL2 Profile) ◼ Complying with IEEE ◼ Selectable Band plan (Symmetric or Asymmetric) 802.3/802.3u/802.3x Selectable target SNR margin (6dB or 9dB) ◼... -
Page 5: Chapter 2 Hardware Installation
Chapter 2 Hardware Installation This chapter shows the front panel and how to install the hardware. 2.1 Front Panel Front panel can be separated into five parts from left to right: (1) DIP switch (2) RJ-45 connector for Ethernet (3) LEDs for Ethernet (4) LEDs for VDSL (5) RJ-45 connector for VDSL The RJ-45 is designed to connect to the Local Network with the Unshielded Twisted Pair (UTP) - Page 6 Color Status Descriptions PWR(Power LED) Green Lights to indicate that the VDSL2 bridge had power Green The device is not ready or has malfunctioned. LNK(Ethernet LED) Green The device has good Ethernet connection. Green Blinking The device is sending or receiving data. Green The LAN not connected.
-
Page 7: Rear Panel
Symmetric: Support the band plan G.997 and provide the symmetric transmission on both downstream and upstream. Asymmetric: Provides highest line rate in short range in asymmetric mode. Pin 4: General protection 9dB: Better channel noise protection with SNR up to 9 dB 6dB: Original channel noise protection with 6 dB SNR. -
Page 8: Installation
2.3 Installation Please see the illustration below Page 8... - Page 9 Appendix I Connector Architecture Ethernet Port Connector (RJ-45) The Ethernet Port interface is an 8 position Modular Jack. The table below displays the pin out assignments. Pin Number Assignment (MDI-X) Figure RX+; Receive data + RX-; Receive data - TX+; Transmit data + Not used Not used Front View...
- Page 10 VDSL Interface Pin Assignments (RJ-45) The VDSL interface is standard eight-pin modular jack. The table below displays the pin out assignments. Pin Number Description Figure Not used Not used Not used ANALOG Input/Output ANALOG Input/Output Front View Not used Not used View Not used Page 11...
- Page 11 Appendix II Chassis Accessory There is also the Chassis solution for application on the rack in CO side. The major feature of the Chassis is listed below: • 2U, 19”, 17-Slot rack • Support 17-slot in one unit • Power Input: AC: 100 ~240V or DC48: 36 ~ 60V •...
Need help?
Do you have a question about the PD-VDSL-MI100 and is the answer not in the manual?
Questions and answers