Related Manuals for FEZIBO FZ-SM03PS-1
Summary of Contents for FEZIBO FZ-SM03PS-1
- Page 1 FZ-SM03PS-1 Single monitor Arm Scan the QR code with your mobile device or follow link helpful videos and specifications related to this product. https://www.facebook.com/Fezibous/...
- Page 2 Safety Hazard Symbols Review: These symbols alert users of a safety condition that demands attention. All users should be able to recognize and understand the significance of the following Safety Hazards if encountered on the product or within the documentation. Children who are not able to recognize and respond appropriately to Safety Alerts should not use this product without adult supervision! Symbol Signal Word...
-
Page 3: Features And Specifications
Features & Specifi cations min220~max275mm 47mm 185mm 60mm 75mm 100mm 114mm CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT Ø35mm CAPACITY. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR! (3.2 - 280° 70° 360° 180° 5° Components Tools Needed 2.5mm M4x16mm (x4) M4x12mm (x4) Screws Screws... - Page 4 STEP 1 A ttach P ole t o the Base Attach pole (B) onto base (C) of monitor stand with bolts (Q) using provided 4mm Allen wrench (R). STEP 2 Choose a mounting option OPTION A: Clamp Installation Install clamp base support (E) onto base of monitor stand with bolts (P) using provided 4mm Allen wrench (R).
- Page 5 Apply pads (J) to bottom of base to prevent table top from being scratched. Adjust the Mount to the Desktop Adjust the Mount to the Desktop Thickness 50-85mm Thickness 10-55mm Secure clamp (F) to upper two holes with Secure clamp (F) to lower two holes with bolts (O) using 4mm Allen wrench (R) for bolts (O) using 4mm Allen wrench (R) for desks with a thickness of 10-55mm.
- Page 6 Attach base support cover (G) to clamp base support (E). Tighten the clamp to the desktop using the plastic knob. STEP 2 (Continued) OPTION B: Grommet Base Installation Slide long screw (H) through the top of the grommet base support (I) and install on base of monitor stand with bolts using 4mm Allen wrench (R).
- Page 7 Position stand on desk with long screw through hole, and secure by using the support plate (K) and washer (M) on underside of the mounting surface, tighten the nut (L) with wrench (U). STEP 3 Assemble the Arm Attach arm assembly (A) onto the pole and secure by using provided 5mm Allen wrench (S).
- Page 8 STEP 4 Attach the monitor to the arm OPTION A: Flat Back Monitor Attach the VESA plate (D) to back of monitor and secure with screws (M-A) or (M-C) with washers (M-E). Avoid excessive tightening screws damage the monitor. OPTION B: Curved Back Monitor Attach the VESA plate (D) to back of monitor and secure with screws (M-B) or (M-D) with washers (M-E) and washers (M-F).
-
Page 9: Step 5 Adjust The Tension
Slide the monitor onto the head of swivel arm, install the security nut (N). Make sure the security nut is installed before you rotate the monitor. STEP 5 Adjust the tension Adjust gas spring tension by turning Be sure to keep the arm in horizontal screw with 6mm Allen wrench (T) . -
Page 10: Step 6 Cable Management
STEP 6 Cable Management For both bottom and upper portion of the spring arm, just slide the cable cover up and away from the spring arm, do not need to take much effort to pull the ends of the cable cover away from the spring arm. - Page 11 STEP 7 Inser t the Allen Wr ench int o the Slot Adjust monitor to the desired position and insert Allen wrenches (R&T) into the slot ± 90° +45° -45° ± 180° ± 180° ± 135°...
- Page 12 If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product. Service@fezibo.com www.facebook.com/Fezi bous www.fezibo.com For more FEZ I BO products, check out our website at: www.fezibo.com...
Need help?
Do you have a question about the FZ-SM03PS-1 and is the answer not in the manual?
Questions and answers