Download Print this page

Frigidaire PLEFMZ99ECJ Service Data Sheet

Electric ranges with es 510 electronic oven control & bake-n-warm™ oven
Hide thumbs

Advertisement

Quick Links

SERVICE DATA SHEET
Electric Ranges with ES 510 Electronic Oven Control & Bake-N-Warm™ Oven (some models)
-
NOTICE
This service data sheet is intended for use by persons
having electrical and mechanical training and a level of knowledge
of these subjects generally considered acceptable in the appliance
repair trade.
The manufacturer cannot be responsible, nor
assume any liability for injury or damage of any kind arising from
the use of this data sheet.
SAFE SERVICING PRACTICES
To avoid the possibility of personal injury and/or property damage, it is
important that safe servicing practices be observed. The following are
examples, but without limitation, of such practices.
1.
Before servicing or moving an appliance remove power cord from
electrical outlet, trip circuit breaker to OFF, or remove fuse.
2.
Never interfere with the proper installation of any safety device.
3.
GROUNDING: The standard color coding for safety ground wires is
GREEN or GREEN WITH YELLOW STRIPES . Ground leads are not
to be used as current carrying conductors.
It is extremely
important that the service technician reestablish all safety
grounds prior to completion of service. Failure to do so will
create a potential safety hazard.
ELECTRONIC OVEN CONTROL (EOC rear view)
EOC P10 BAKE-N-WARM™
CONNECTION (some models)
IMPORTANT
DO NOT REMOVE THIS BAG
OR DESTROY THE CONTENTS
WIRING DIAGRAMS AND SERVICE
INFORMATION ENCLOSED
REPLACE CONTENTS IN BAG
p/n 316441475 (0607)
4.
Prior to returning the product to service, ensure that:
• All electric connections are correct and secure.
• All electrical leads are properly dressed and secured away from sharp edges,
high-temperature components, and moving parts.
• All uninsulated electrical terminals, connectors, heaters, etc. are adequately
spaced away from all metal parts and panels.
• All safety grounds (both internal and external) are correctly and securely
reassembled.
OVEN CALIBRATION
Set the electronic oven control for normal baking at 350°F. Obtain an average oven
temperature after a minimum of 5 cycles. Press STOP/CLEAR to end bake mode.
TEMPERATURE ADJUSTMENT
1.
Set EOC to bake at 550°F.
2.
Within 5 seconds of setting 550°F, press and hold the bake pad for approximately
15 seconds until a single beep is heard (longer may cause F11 shorted keypad
alarm).
3.
Calibration offset should appear in the display.
4.
Refer to the instructions in the Use & Care to adjust the oven temperature up or
down.
5.
Once the desired (-35° to 35°) offset has been applied, press STOP/CLEAR.
Note: Changing calibration affects normal Bake mode. The adjustments made will not
change the Self-Cleaning cycle temperature.
BAKE-N-WARM™
DOUBLE OVEN
CONTROL BOARD
(REAR VIEW)
EOC P4 BAKE-N-WARM™
CONNECTION (some models)
EOC P5 CONNECTIONS
RESISTANCE TEMPERATURE DECTECTOR
ELECTRONIC OVEN CONTROL FAULT CODE DESCRIPTIONS
Fault Code
F10
Runaway Temperature.
F11
Shorted Keypad.
F12
Bad Micro Identification.
F13
Bad EEPROM Identification/Checksum error.
F20
Communication failure between EOC & ESEC system
F26
Communication failure with Mini Oven Control Board.
F30
Shorted Probe connection.
P4
P3
F31
F90
Maximum oven door unlock time exceeded.
F91
Maximum oven door unlock attempts exceeded.
F92
Maximum oven door open time exceeded.
F93
Maximum oven door lock time exceeded.
F94
Maximum oven door lock attempts exceeded.
CIRCUIT ANALYSIS MATRIX
Temperature (°F)
Likely Failure Condition/Cause
1. (F10 only) Check RTD Sensor Probe & replace if necessary. If oven is overheating, disconnect
power. If oven continues to overheat when the power is reapplied, replace EOC. Severe
overheating may require the entire oven to be replaced should damage be extensive.
2. (F11, 12 & 13) Disconnect power, wait 30 seconds and reapply power.
3. (F11, 12 & 13) If fault returns upon power-up, replace EOC.
1. Test harness/connections P4 (EOC) & P11 (Surface Element Control Board)
2. If harness checks O.K. failure can be caused by faulty UIB, Surface Element Control Board
or EOC.
1. Check harness & connectors from the EOC to Mini Oven Control Board. Check for 15VDC
to Mini Oven Control Board (red & gray wires). If harness and voltage are good replace Mini Oven
Control Board. If fault returns replace the EOC.
1. (F30 or F31) Check resistance at room temperature & compare to RTD Sensor resistance chart.
If resistance does not match the RTD chart replace RTD Sensor Probe. Check Sensor wiring
harness between EOC & Sensor Probe connector.
2. (F30 or F31) Check resistance at room temperature, if less than 500 ohms, replace RTD Sensor
Probe. Check for shorted Sensor Probe harness between EOC & Probe connector.
1. (F90, 91, 92, 93 & 94) Check the wiring between EOC & Lock Motor Micro Switch.
2. (F90, 91, 92, 93 & 94) Replace the Motor Door Latch assembly if necessary.
3. (F90, 91, 92, 93 & 94) Check for binding of the Latch Cam, Lock Motor Rod & Lock Motor Cam.
4. (F90, 91, 92, 93 & 94) Check to see if Lock Motor Coil is open. If open, repl;ace Lock Motor
Assembly.
5. (F90, 91, 92, 93 & 94) Lock Motor continuosly runs - if Micro Switch is open, replace Lock Motor
Assembly.
6. (F92, 93 & 94) Check oven door Light Switch - if open, replace Switch.
7. If all situations above do not solve probem, replace EOC.
RTD SCALE
Resistance (ohms)
32 ± 1.9
1000 ± 4.0
75 ± 2.5
1091 ± 5.3
250 ± 4.4
1453 ± 8.9
350 ± 5.4
1654 ± 10.8
450 ± 6.9
1852 ± 13.5
550 ± 8.2
2047 ± 15.8
650 ± 9.6
2237 ± 18.5
900 ± 13.6
2697 ± 24.4
Suggested Corrective Action

Advertisement

loading

  Related Manuals for Frigidaire PLEFMZ99ECJ

  Summary of Contents for Frigidaire PLEFMZ99ECJ

  • Page 1 SERVICE DATA SHEET Electric Ranges with ES 510 Electronic Oven Control & Bake-N-Warm™ Oven (some models) Prior to returning the product to service, ensure that: NOTICE This service data sheet is intended for use by persons • All electric connections are correct and secure. having electrical and mechanical training and a level of knowledge •...
  • Page 2 GENERAL TROUBLESHOOTING DIAGRAM GENERAL TROUBLESHOOTING SCHEMATIC WARNING AVERTISSEMENT DISCONNECT POWER BEFORE SERVICING DISCONNECT POWER BEFORE SERVICING DEBRANCHEZ L' APPAREL DE DEBRANCHEZ L' APPAREL DE L' ALIMENTATION ELECTRIQUE AVANT L' ALIMENTATION ELECTRIQUE AVANT DE FAIRE TOUT SERVICE D' ENTRETIEN DE FAIRE TOUT SERVICE D' ENTRETIEN TRACER WIRE: WIRE COLOR NOTED TRACER WIRE: WIRE COLOR NOTED FIRST, STRIPE NEXT.