Table of Contents
Advertisement
[YES]
9. Press the
button display "EFB =
Then, the optical pick-up moves to the pit area automatically
and servo is imposed.
10. Observe the waveform of the oscilloscope, and check that the
specified value is satisfied. Do not turn the = ˜ +
knob.
(Traverse Waveform)
VC
Specified value : Below 10% offset value
Offset value (%) =
[YES]
11. Press the
button display "EF MO CHECK"
The disc stops rotating automatically.
[ EJECT]
6
12. Press the
button and remove the disc.
13. Load the check disc (MD) TDYS-1.
14. Turn the = ˜ + knob and display "EF CD CHECK"
(C04).
[YES]
15. Press the
button and display "EFB =
imposed automatically.
16. Observe the waveform of the oscilloscope, and check that the
specified value is satisfied. Do not turn the = ˜ +
knob.
(Traverse Waveform)
VC
Specified value : Below 10% offset value
Offset value (%) =
[YES]
17. Press the
button and display "EF CD CHECK".
[ EJECT]
6
18. Press the
button and take out the check disc.
MO-P".
A
B
I A – B I
X 100
2 (A + B)
CD". Servo is
A
B
I A – B I
X 100
2 (A + B)
6-4. Focus Bias Check
Change the focus bias and check the focus tolerance amount.
Checking Procedure :
1. Load the test disk (MDW-74/AU-1).
2. Turn the = ˜ + knob and display "CPLAY MODE"
(C30).
[YES]
3. Press the
[MENU/NO]
4. Press the
displayed.
5. Turn the = ˜ + knob and display "FBIAS CHECK"
(C05).
[YES]
6. Press the
The first four digits indicate the C1 error rate, the two digits
after [/] indicate ADER, and the 2 digits after [c =] indicate
the focus bias value.
Check that the C1 error is below 50 and ADER is below 2.
[YES]
7. Press the
Check that the C1 error is about 200 and ADER is below 2.
[YES]
8. Press the
Check that the C1 error is about 200 and ADER is below 2.
[MENU/NO]
9. Press the
ton and take out the test disc.
6-5. C PLAY Checking
MO Error Rate Check
Checking Procedure :
1. Load the test disk (MDW-74/AU-1).
2. Turn the = ˜ + knob and display "CPLAY MODE"
(C30).
[YES]
3. Press the
4. The display changes to "C =
5. If the C1 error rate is below 80, check that ADER is below 2.
[MENU/NO]
6. Press the
[ EJECT]
6
button and take out the test disc.
CD Error Rate Check
Checking Procedure :
1. Load the check disc (MD) TDYS-1.
2. Turn the = ˜ + knob and display "CPLAY MODE"
(C30).
[YES]
3. Press the
4. The display changes to "C =
5. Check that the C1 error rate is below 50.
[MENU/NO]
6. Press the
[ EJECT]
6
button and take out the check disc.
6-6. Self-Recording/playback Check
Prepare a continuous recording disc using the unit to be repaired
and check the error rate.
Checking Procedure :
1. Insert a recordable disc (blank disc) into the unit.
2. Turn the = ˜ + knob to display "CREC MODE"
(C31).
[YES]
3. Press the
4. When recording starts, "
"CREC @@@@" (@@@@ is the address), and recording starts.
5. About 1 minute later, press the
continuous recording.
6. Turn the = ˜ + knob to display "CPLAY MODE"
(C30).
[YES]
7. Press the
8. "C =
AD =
9. Check that the C1 error becomes below 80 and the AD error
below 2.
[MENU/NO]
10. Press the
[ EJECT]
6
button and take out the disc.
– 24 –
button twice and display "CPLAY MID".
button when "C =
button and display "
/
button and display "
/
button and display "
/
[ EJECT]
button, next press the
button and display "CPLAY MID".
AD =
".
button, stop playback, press the
button twice and display "CPLAY MID".
AD =
".
button, stop playback, press the
button to display the "CREC MID".
REC
" is displayed, this becomes
[MENU/NO]
button to display "CPLAY MID".
" will be displayed.
button to stop playback, and press the
AD =
" is
c =
".
b =
".
a =
".
6
but-
button to stop
Advertisement
Table of Contents
