Steamer Operation - Maxwell MW-3703 B Manual Instruction

ENGLISH
completely. Removable parts should be dry
and cool.
• Do not use the unit outdoors.
• Never pull the power cord, when
disconnecting the unit from the mains, take
the plug and carefully pull it out of the socket.
• Do not disassemble the unit by yourself, if
any malfunction is detected or after it was
dropped, apply to the nearest authorized
service center.
THE UNIT IS INTENDED FOR HOUSEHOLD
USAGE ONLY
UNIT PURPOSE
The unit can be used for any types of clothes and
fabrics. If you have doubts about steaming any
certain kind of fabric or clothes you should follow
manufacturer's recommendations. If such infor-
mation is not available, try to steam the fabric
back-side.
When steaming such fabrics as silk or corduroy,
treat the fabric with steam by holding the sprayer
(15) away from the material.
Use the brush attachment (16) to remove unnec-
essary lint and threads.
BEFORE THE FISRT USE
1. Unpack the unit, remove any stickers that
prevent normal operation of the unit, place
the unit on a flat stable surface.
Note: In case of unit transportation or stor-
age at low temperature it is necessary to
keep it for at least two hours at room tem-
perature before switching on.
2. Loosen the clamp (7) rotating it counterclock-
wise.
3. Set the telescopic stand (9) into the clamp
opening (7).
4. Fix the telescopic stand rotating the clamp (7)
clockwise.
5. Loosen the clamps (10), extend the stand (9)
to the required length, fix the clamps (10).
6. Extend the hanger (13), set the extension
bars (18) according to the picture 1 and put
the clamps (19) on.
7. Set the hanger (13) on the stand (9).
8. Fix the steam tube (11) with the nut (8) screw-
ing it clockwise firmly. When screwing the nut
(8) hold the tube with another hand in order to
prevent its turning with the nut.
MW-3703.indd 8
Note: When screwing the nut (8) do not apply
too strong efforts.
9. Fix the sprayer (15) on the holder (14).

STEAMER OPERATION

1. Before operate the steamer fill the tank (5)
with water. To remove the water tank take it
by handle (6) and pull upwards.
2. Turn over the tank (5) and open the lid (4).
3. Fill the water tank (5) with water, close the lid (4).
Attention!
Before removing the water tank (5) make
sure that the unit is unplugged.
Do not use hot water. To extend the opera-
tion period of the steamer it is recommend-
ed to use distilled and demineralised water.
Do not switch on the unit if it is empty.
4. Set the water tank (5) to its place.
5. Fix clean clothes on the hanger (13).
Note: Be careful when fixing clean clothes
on the hanger (13). Too strong pressure
may cause its damage.
Never steam clothes on a person as the steam
temperature is very high, use a hanger (13).
6. Connect the unit to the mains.
7. Set the switch (1) to the "ON" position, the
illumination of the switches (1) and (2) will
light up.
8. Select the operation mode using the switch (2).
Operating Power
mode
800 W 800 W
1600 W 1600 W
9. Wait for intensive steam release from the
sprayer openings (15). It will take some time.
10. H old the sprayer (15) by the handle (12),
take the sprayer (15) to the bottom of clothes
item. Steam will go along the external and
internal surface of fabric ironing the folds.
Slowly move the sprayer (15) vertically bot-
tom-upwards. Straighten the fabric using
the free hand. Fix trousers with the trousers
clamps (17).
Note: Do not allow bending of the steam
tube (11).
8
Steam generation
medium steam
generation intensity
maximum steam
generation intensity
12.07.2012 10:11:04