Cateye Adventure CCAT2W-110930 Manual

CATEYE ADVENTURE
CYCLOCOMPUTER CC-AT200W
U.S. Pat. Nos. 5236759/6957926 Pat./Design Pat. Pending Copyright© 2011 CATEYE Co., Ltd.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two condi-
tions:(1)This device may not cause harmful interference, and (2) this device must accept any inter-
ference received, including interference that may cause undesired operation.
Modifications
The FCC requires the user to be notified that any changes or modifications made to this device that are
not expressly approved by CatEye Co., Ltd. May void the user 's authority to operate the equipment.
WARNING / CAUTION
• Do not concentrate on the computer while riding. Ride safely!
• Install the magnet, sensor, and bracket securely. Check these periodically.
• If a child swallows a battery, consult a doctor immediately.
• Do not leave the computer in direct sunlight for a long period of time.
• Do not disassemble the computer.
• Do not drop the computer to avoid malfunction or damage.
• When using the computer installed on the bracket, change the
dots below the screen, or by pressing on the SSE simultaneously, to start or stop the timer.
Pressing hard on other areas may result in malfunction or damage to the computer.
• Be sure to tighten the dial of the FlexTight bracket by hand. Tightening it strongly using a
tool, etc. may damage the screw thread.
Before using the computer, please thoroughly read this manual and keep
it for future reference.
Preparing the computer
Battery case cover
MENU
Pressure sensor
AC
MODE
SSE
km/h mph : Speed unit
: Wheel size icon
: Sensor signal reception icon
When using the computer for the first time or resetting to the factory
default setting, format according to the following procedure.
1
Format (initialize)
1. Press and hold the MENU button.
2. Press the AC button.
3. Release the AC button.
4. Release the MENU button.
2
Select the speed and temperature unit
When MODE and SSE are pressed simultane-
ously, "Speed unit" or "Temperature unit" can be
selected. Select "km/h" or "mph" for the speed
unit, and "°C" or "°F" for the temperature unit.
Press MENU to register.
Switch the screen (By Unit
pressing simultaneously) selection
MODE MODE
MODE + SSE MODE + SSE
3
Enter the tire circumference
Enter the tire circumference of your bicycle in mm.
* Refer to the tire circumference reference table.
Increase Move digits (By press-
the value ing simultaneously)
MODE MODE
MODE + SSE MODE + SSE
4
Set the sensor ID
Hold the computer body close to the sensor (20
- 70cm), and press and hold the RESET but-
ton on the sensor with a sharp object. Sensor
will randomly generate an ID number for the
computer body to receive, and displays on the
screen. If successfully synchronized, screen will
automatically move on to Clock setting screen.
* When setting the sensor ID, place the sensor at least 20 cm (approxi-
mately 8 inches) away from the computer. Press and hold the RESET
button, the sensor will send the ID when releasing the button.
* The computer is on standby for 5 minutes while setting the sensor ID. It dis-
plays "ERROR", and cancels the ID when no ID signal is received during the
standby, or you press MODE and SSE simultaneously. Screen will move on to
clock setting. Without the ID, speed cannot be detected and displayed. Be sure
to set the sensor ID according to "Sensor ID setting" on the menu screen.
* Original ID is saved if you cancel the ID.
Start the ID set- Cancel the ID or
ting (By press- reset (By pressing
ing & holding) simultaneously)
MODE + SSE MODE + SSE
RESET
5
Set the clock
When MODE and SSE are pressed simultane-
ously, "Displayed time", "Hour", and "Minute"
will appear, in this order.
Switch the screen
24h ↔ 12h,
or move digits
or increase
(By pressing
the value
MODE MODE
MODE + SSE MODE + SSE
simultaneously)
Measure wheel circumference (L) of your bike
To get the most accurate calibration do a wheel roll out. With the valve stem
perpendicular to the ground, mark the pavement at the valve stem. With the
riders weight on the bike, roll the wheel one tire revolution in a straight line
and mark the ground when the valve stem is perpendicular to the ground
again. Measure the distance in millimeters. This is the most accurate wheel
calibration number.
MODE by pressing on the four
Operation of buttons when the computer is
mounted on the bracket
Click
MODE + SSE
MODE
Press the SSE button with
Press only the computer
body. the computer body together.
SSE button by itself does
not function.
Tire circumference
reference table
ETRTO Tire size
47-203 12x1.75
54-203 12x1.95
MENU
40-254 14x1.50
47-254 14x1.75
40-305 16x1.50
47-305 16x1.75
AC
54-305 16x2.00
28-349 16x1-1/8
37-349 16x1-3/8
17x1-1/4
32-369
369
( )
40-355 18x1.50
47-355 18x1.75
32-406 20x1.25
35-406 20x1.35
40-406 20x1.50
47-406 20x1.75
50-406 20x1.95
28-451 20x1-1/8
Register
37-451 20x1-3/8
the setting
37-501 22x1-3/8
40-501 22x1-1/2
MENU MENU
47-507 24x1.75
50-507 24x2.00
54-507 24x2.125
25-520 24x1
(
24x3/4
Tubuler
28-540 24x1-1/8
Register
32-540 24x1-1/4
the setting
25-559 26x1
(
32-559 26x1.25
MENU MENU
37-559 26x1.40
40-559 26x1.50
47-559 26x1.75
50-559 26x1.95
54-559 26x2.10
57-559 26x2.125
58-559 26x2.35
75-559 26x3.00
28-590 26x1-1/8
37-590 26x1-3/8
37-584 26x1-1/2
650C Tubuler
26x7/8
20-571 650x20C
23-571 650x23C
650x25C
25-571
26x1 (
40-590 650x38A
40-584 650x38B
25-630 27x1
(
28-630 27x1-1/8
32-630 27x1-1/4
37-630 27x1-3/8
18-622 700x18C
19-622 700x19C
20-622 700x20C
23-622 700x23C 2096
Move to Clock
25-622 700x25C
Setting when no
28-622 700x28C
ID has been set 30-622 700x30C
MENU MENU
32-622 700x32C
700C
Tubuler
35-622 700x35C
38-622 700x38C
40-622 700x40C
42-622 700x42C
44-622 700x44C
Register 45-622 700x45C
47-622 700x47C
the setting
54-622 29x2.1
(Finish)
MENU MENU
60-622 29x2.3
L mm
CCAT2W-110930 4
• When cleaning the computer, bracket and sensor, do not use thinners, benzene, or alcohol.
• A temperature sensor is built in the computer. If the sensor is heated by direct sunlight or
body heat, it may not indicate the temperature correctly.
• The altitude data with this unit is for reference only; accordingly, do not use this unit as a
measuring device for professional use.
• Dispose of used batteries according to local regulations.
• LCD screen may be distorted when viewed through polarized sunglass lenses.
Wireless Sensor
In order to prevent any interference with the sensor signal, the transmission range is designed
to be 20 to 70 cm, in addition to use of the ID code. (This receiving range is only a reference.)
Please note the following points.
• To use this unit, the sensor ID has to be set.
• Two different IDs, ID1 and ID2, can be registered to this unit, which are identified automatically.
• The computer cannot receive when the distance between the sensor and computer is too long.
Temperature drop and battery drain may worsen the receiving sensitivity even if they are within
the transmission range.
Interference may occur, resulting in incorrect data, if the computer is:
• Near a TV, PC, radio, motor, or in a car or train.
• Close to a railroad crossing, railway tracks, TV stations and/or radar base.
• Using with other wireless devices, or some particular battery lights.
After changing the battery, or when the computer displays an error, restart the com-
puter according to the following procedure.
1. Press the AC button on the back of the computer.
2. Set the clock. Refer to "Preparing the computer 5".
* The stored sea level altitude, home altitude, speed unit, wheel size, sensor ID, countdown dis-
tance, selected wheel, AT setting, total distance and total altitude gain will not be changed after
pressing the AC button.
How to install the unit on your bicycle
2 4
1
3
7
6
8
L ( mm )
935
940
Install the sensor and magnet
1020
1055
The distance from
A
1185
1195
the computer to the
1245
sensor is within the
1290
1300
transmission range.
1340
1340
1350
1450
1460
1490
Max
1515
70 cm
1565
1545
1615
1770
1785
1890
1925
1965
1
Install the sensor
520 1753
)
1785
4
1795
1905
559 1913
)
1950
6
2005
2010
2023
2050
* Install the sensor to the front fork as high as possible.
2068
2070
3
Attach the bracket to the stem or handlebar
2083
2170
When attaching the bracket to the stem
1970
2068
2100
1920 2
1
1938
1944
1952
571 )
2125
2105
630 2145
) When attaching the bracket to the handlebar
2155
* On account of the receiving sensitivity, attach the
2161
2169
bracket so that the computer is kept horizontal. Handlebar
2070
2080
2086
2
1
2105
2136
2146
2155
2130
2168
4
Remove/install the computer
2180
2200
2224
2235
Click
2242
2268
2288
2326
push it out as if lifting the front up
* After installation, check that the speed is displayed on the computer when gently turning the
front wheel. When it is not displayed, check the positions of
How to restart
1 Bracket band
2 Bracket
5
Nut
3
4 Sensor
5 Magnet
6 Sensor rubber pad
7 Bracket rubber pad
8 Nylon ties (x2)
The magnet passes The clearance between
B C
through the sensor zone. the sensor and mag-
net is 5 mm or less.
Sensor zone
5
4 5
Right front fork (inside)
* The magnet may be installed anywhere on the spoke if the
above installation conditions are satisfied.
2
Right front fork
Pull securely
8
Stem
7
7
* For wing type handlebar or oversized stem,
bracket can be mounted using the Bracket
While supporting it by hand,
Holder and nylon ties. (Option)
2
,
A
ENG
0678
4
Install the magnet
Spoke on the right
5
To the sensor zone
Cut
Caution:
Round off the cut edge
of the bracket band to
prevent injury.
3
, and .
B C
1