Table of Contents
Advertisement
W2E200-HH38-05
3.2 Nominal data
Motor
M2E068-BF
Phase
1~
Nominal voltage / VAC
230
Frequency / Hz
50
Method of obtaining
fa
data
Valid for approval/
CE
standard
-1
Speed (rpm) / min
2550
Power consumption / W
64
Current draw / A
0.29
Capacitor / µF
1.5
Capacitor voltage / VDB
400
Max. back pressure / Pa
100
Min. ambient
-25
temperature / °C
Max. ambient
60
temperature / °C
Starting current / A
0.55
ml = Max. load · me = Max. efficiency · fa = Free air
cs = Customer specification · ce = Customer equipment
Subject to change
3.3 Technical description
Weight
2.3 kg
Size
200 mm
Motor size
68
Rotor surface
Painted black
Blade material
Sheet steel, painted black
Housing material
Die-cast aluminum
Guard grille material
Steel, galvanized and coated with white-
aluminum plastic (RAL 9006)
Number of blades
9
Airflow direction
V
Direction of rotation
Counterclockwise, viewed toward rotor
Degree of protection
IP44; installation- and position-dependent
Insulation class
"B"
Moisture (F) /
H0 - dry environment
Environmental (H)
protection class
Installation position
Any
Condensation
None
drainage holes
Mode
S1
Motor bearing
Ball bearing
Touch current
< 0.75 mA
according to IEC
60990 (measuring
circuit Fig. 4, TN
system)
Electrical hookup
Terminal strip; Capacitor connected
Motor protection
Thermal overload protector (TOP)
internally connected
with cable
Variable
Protection class
I (with customer connection of protective
earth)
Item no. 14872-5-9970 · ENU · Change 232995 · Approved 2021-06-11 · Page 5 / 11
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
Operating instructions
1~
1~
230
230
60
60
fa
fa
CE
UL 2111
2800
2800
80
85
0.35
0.36
1.5
1.5
400
400
120
120
-25
-25
65
65
0.54
0.54
Motor capacitor
S0
according to EN 60252-
1 in safety protection
class
Conformity with
EN 60335-1; CE
standards
Approval
UL 507; VDE; CSA C22.2 No. 113
With regard to cyclic speed loads, note that the rotating parts of
the device are designed for a maximum of one million load
cycles. If you have special questions, consult ebm-papst for
support.
; Use the device in accordance with its degree of protection.
Information on surface quality
The surfaces of the products conform to the generally applicable industrial
standard. The surface quality may change during the production period.
This has no effect on strength, dimensional stability and dimensional
accuracy.
The color pigments in the paints used perceptibly react to UV light over
the course of time. The product is to be protected against UV radiation to
prevent the formation of patches and fading. Changes in color are not a
reason for complaint and are not covered by the warranty. UV radiation
in the frequency range and the intensity of natural solar radiation has no
effect on the technical properties of the products.
3.4 Mounting data
Any further mounting data required can be taken from the product
drawing or Section Chapter 4.1 Mechanical connection.
Strength class of
8.8
screws
For screw clearance, see Chapter 3.1 Product drawing
; Secure the screws against unintentional loosening (e.g. use self-
locking screws).
3.5 Transport and storage conditions
Max. permitted
+ 80 °C
ambient temp. for
motor (transport/
storage)
Min. permitted
- 40 °C
ambient temp. for
motor (transport/
storage)
Advertisement
Table of Contents
