Table of Contents
Advertisement
G2E120-AR77-A6
3.2 Nominal data
Motor
M2E068-BF
Phase
1~
Nominal voltage / VAC
230
Frequency / Hz
50
Method of obtaining
fa
data
Valid for approval/
CE
standard
-1
Speed (rpm) / min
2350
Power consumption / W
80
Current draw / A
0.35
Capacitor / µF
2
Capacitor voltage / VDB
450
Capacitor standard
S0 (CE)
Min. back pressure / Pa
0
Min. ambient
-25
temperature / °C
Max. ambient
45
temperature / °C
Starting current / A
0.47
ml = Max. load · me = Max. efficiency · fa = Free air
cs = Customer specification · ce = Customer equipment
Subject to change
3.3 Technical description
Weight
2.02 kg
Size
120 mm
Motor size
68
Rotor surface
Unpainted
Impeller material
Sheet steel, galvanized
Housing material
Die-cast aluminum
Direction of rotation
Clockwise, viewed toward rotor
Degree of protection
IP44; installation- and position-dependent
Insulation class
"B"
Moisture (F) /
H0 - dry environment
Environmental (H)
protection class
Installation position
Shaft horizontal
Condensation
None
drainage holes
Mode
S1
Motor bearing
Ball bearing
Touch current
< 0.75 mA
according to IEC
60990 (measuring
circuit Fig. 4, TN
system)
Electrical hookup
Terminal strip; Via terminals, capacitor
connected
Motor protection
Thermal overload protector (TOP)
internally connected
with cable
Axial
Protection class
I (with customer connection of protective
earth)
Motor capacitor
S0
according to EN 60252-
1 in safety protection
class
Item no. 15318-5-9970 · ENU · Change 257459 · Approved 2022-05-06 · Page 5 / 11
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
Operating instructions
Conformity with
standards
Approval
1~
230
60
fa
; Use the device in accordance with its degree of protection.
CE
Information on surface quality
The surfaces of the products conform to the generally applicable industrial
2450
standard. The surface quality may change during the production period.
100
This has no effect on strength, dimensional stability and dimensional
0.44
accuracy.
2
The color pigments in the paints used perceptibly react to UV light over
450
the course of time. The product is to be protected against UV radiation to
S0 (CE)
prevent the formation of patches and fading. Changes in color are not a
0
reason for complaint and are not covered by the warranty. UV radiation
-25
in the frequency range and the intensity of natural solar radiation has no
effect on the technical properties of the products.
55
3.4 Mounting data
0.47
Any further mounting data required can be taken from the product
drawing or Section Chapter 4.1 Mechanical connection.
Strength class of
screws
For screw clearance, see Chapter 3.1 Product drawing
; Secure the screws against unintentional loosening (e.g. use self-
3.5 Transport and storage conditions
Max. permitted
ambient temp. for
motor (transport/
storage)
Min. permitted
ambient temp. for
motor (transport/
storage)
EN 60335-1; CE
EAC
With regard to cyclic speed loads, note that the rotating parts of
the device are designed for a maximum of one million load
cycles. If you have special questions, consult ebm-papst for
support.
8.8
locking screws).
+ 80 °C
- 40 °C
Advertisement
Table of Contents
