Do you have a question about the UltraLink ULM300D and is the answer not in the manual?
Questions and answers
DAN WITSCH
February 4, 2025
broke reciever, where can I get a replacement
ulm300d
1 comments:
Mr. Anderson
May 14, 2025
You can find a replacement receiver for the Behringer ULM300D listed as "BEHRINGER ULTRALINK DEDICATED ULM300D RECEIVER ONLY" on eBay for AU $119.00.
This answer is automatically generated
aurelio
February 3, 2025
como configurar microfono ulm 100
1 comments:
Mr. Anderson
February 10, 2025
1. Connect the Receiver: Plug the USB wireless receiver into a compatible BEHRINGER mixer, powered speaker, or a USB port on a computer.
2. Power On the Microphone: Press and hold the VOLUME UP button (long press) to turn on the microphone.
3. Check LED Status: - Flashing Amber: No signal. - Solid Green: Connected and active. - Flashing Green: Connected but muted. - Alternating Green/Red: Low battery.
4. Adjust Volume: - Press the VOLUME UP button (short press) to increase volume. - Press the VOLUME DOWN button (short press) to decrease volume.
5. Mute/Unmute: - Press the VOLUME DOWN button (short press) to mute. - Press the VOLUME UP button (short press) to unmute.
6. Power Off: - From the Mute mode, press and hold the VOLUME DOWN button to turn off the microphone. - The microphone will also turn off automatically if left in Mute mode for 10 minutes.
7. Battery Replacement: - Unscrew the bottom of the microphone. - Insert new batteries with the correct polarity. - Reattach the cover and turn the microphone back on.
The microphone is now configured and ready for use.
High-performance uhf wireless in-ear monitoring system (57 pages)
Summary of Contents for Behringer UltraLink ULM300D
Page 1
Quick Start Guide ULTRALINK ULM300USB Model:ULM300M, ULM300D High-Performance 2.4 GHz Digital Wireless System with Handheld Microphone and Dual-Mode USB Receiver A54-00000-00000...
ULM300USB Getting Started Plug the USB wireless receiver to the designated USB socket on wireless-enabled BEHRINGER mixers, powered speakers or other compatible products, or to a USB port on a computer. The POWER/STATUS LED on the receiver will slowly fl ash amber.
FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION ULM300M, ULM300D Responsible Party Name: MUSIC Group Services NV Inc. 5270 Procyon Street Address: Las Vegas, NV 89118 +1 702 800 8290 Phone Number: ULM300M, ULM300D complies with the FCC rules as mentioned in the following paragraph: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part...
Need help?
Do you have a question about the UltraLink ULM300D and is the answer not in the manual?
Questions and answers
broke reciever, where can I get a replacement ulm300d
You can find a replacement receiver for the Behringer ULM300D listed as "BEHRINGER ULTRALINK DEDICATED ULM300D RECEIVER ONLY" on eBay for AU $119.00.
This answer is automatically generated
como configurar microfono ulm 100
1. Connect the Receiver: Plug the USB wireless receiver into a compatible BEHRINGER mixer, powered speaker, or a USB port on a computer.
2. Power On the Microphone: Press and hold the VOLUME UP button (long press) to turn on the microphone.
3. Check LED Status:
- Flashing Amber: No signal.
- Solid Green: Connected and active.
- Flashing Green: Connected but muted.
- Alternating Green/Red: Low battery.
4. Adjust Volume:
- Press the VOLUME UP button (short press) to increase volume.
- Press the VOLUME DOWN button (short press) to decrease volume.
5. Mute/Unmute:
- Press the VOLUME DOWN button (short press) to mute.
- Press the VOLUME UP button (short press) to unmute.
6. Power Off:
- From the Mute mode, press and hold the VOLUME DOWN button to turn off the microphone.
- The microphone will also turn off automatically if left in Mute mode for 10 minutes.
7. Battery Replacement:
- Unscrew the bottom of the microphone.
- Insert new batteries with the correct polarity.
- Reattach the cover and turn the microphone back on.
The microphone is now configured and ready for use.
This answer is automatically generated