Samsung CLP-775ND Series Service Manual page 79

Depth 1 Depth 2
105-Duty 0030-MHV DC K
0000-Deve DC Y
0010-Deve DC M
0020-Deve DC C
0030-Deve DC K
0040-Deve VPP Y
0050-Deve VPP M
0060-Deve VPP C
106-Deve
0070-Deve VPP K
0080-Dev AC Y
0090-Dev AC M
0100-Dev AC C
0110-Dev AC K
0120-Deve AC Freq
0000-THV Y
0010-THV M
0020-THV C
0030-THV K
107-Transfer 0040-THV Low Y
0050-THV Low M
0060-THV Low C
0070-THV Low K
0130-ATTR+ Bias
0000-Ready Temp
0010-Print Temp
0020-Low Power
Temp
0070-Bond Temp
109-Temp
Offset 0080-Trans Temp
0100-Envelopes Temp
0110-Labels Temp
0120-Fuser Bias Duty
0130-Thick Temp
0040-LD Power Y
0050-LD Power M
110-LD
Power
0060-LD Power C
0070-LD Power K
111-Toner
Copyright© 1995-2016 SAMSUNG. All rights reserved.
Min/Max,
Meaning
Default
[-15~15] 0* Set up the Charger(MHV)'s DC control duty
[-25~25] 0* Set up the Yellow Dev DC control duty
[-25~25] 0* Set up the Magenta Dev DC control duty
[-25~25] 0* Set up the Cyan Dev DC control duty
[-25~25] 0* Set up the Black Dev DC control duty
[-25~25] 0* Set up the Yellow Dev PP control duty
[-25~25] 0* Set up the Magenta Dev PP control duty
[-25~25] 0* Set up the Cyan Dev PP control duty
[-25~25] 0* Set up the Black Dev PP control duty
[-25~25] 0* Set up the Yellow Dev AC control duty
[-25~25] 0* Set up the Magenta Dev AC control duty
[-25~25] 0* Set up the Cyan Dev AC control duty
[-25~25] 0* Set up the Black Dev AC control duty
[-500~500]
Set up the Dev AC frequncy
0*
[-25~25] 0* Set up the yellow transfer DC normal voltage control duty
[-25~25] 0* Set up the magenta transfer DC normal voltage control duty
[-25~25] 0* Set up the cyan transfer DC normal voltage control duty
[-25~25] 0* Set up the black transfer DC normal voltage control duty
[-10~10] 0* Set up the yellow transfer DC low voltage control duty
[-10~10] 0* Set up the magenta transfer DC low voltage control duty
[-10~10] 0* Set up the cyan transfer DC low voltage control duty
[-10~10] 0* Set up the black transfer DC low voltage control duty
[-10~10] 0* Set up the ATTR plus bias voltage on at normal drive level
[-10~10] 0* Target Temperature value setting during standby state.
[-10~10] 0* Target Temperature value setting during print state.
[-10~10] 0* Target Temperature value setting during power save state.
[-10~10] 0* Bond type paper fixing temperature offset
[-10~10] 0* Transparency(OHP) type paper temperature offset
[-10~10] 0* Envelopes type paper temperature offset
[-10~10] 0* Labels type paper temperature offset
[-10~10] 0* Set up the fuser roll voltage control duty
[-10~10] 0* Thick type paper temperature offset
[-10~10] 0* Yellow LD Power at Normal Speed
[-10~10] 0* Magenta LD Power at Normal Speed
[-10~10] 0* Cyan LD Power at Normal Speed
[-10~10] 0* Black LD Power at Normal Speed
Not Available
4. Alignment and Troubleshooting
4-20