Table of Contents
Advertisement
Quick Links
50M/100M/200M QUAD PHOTOELECTRIC BEAM SENSOR
Thanks for purchasing
●
Large and expanded protection range.
●
Quad Photoelectric Beam 4PH-50 / 100
●
4 sets
4PH-50 / 100 / 200 TA/TAI
beams protection.
●
The product is designed with FDM ( Frequency-Division Multiplexing ) TDM ( Time-Division Multiplexing ) technology to prevent interference.
PRODUCT PARTS：
PARTS DESCRIPTION
Main Base
4PH-XXXTA
Cover
4PH-50TA / 4PH100TA / 4PH-200TA
4PH-50TAI / 4PH100TAI / 4PH-200TAI
product. Read this instruction manual before using the product to make sure that you u e it correctly.
FEATURES
/ 200
TA/TAI with detection range at 50m , 100m
could be stacked and operated on the same pole with same direction by total four(4) duals and sixteen(16)
Lens
Horizontal angle
coarse adjustment
Screw
Horizontal angle
fine adjustment Screw
Panel
Vertical angle
Mounting Piece
adjustment Screw
View Finder
U-Shaped
Brackets
Mounting Plate
Main Base
4PH-XXXTAI
and 200m
View Finder
Vertical angle
adjustment Screw
Horizontal angle
fine adjustment Screw
Horizontal angle
coarse adjustment
Screw
Lens
Unit Base (ATI)
MAIN BASE
Cover Locking Screw
1
(
TA TAI
/
INSTRUCTION MANUAL
s
as well.
Accessories
Hex Screws
4x25
Hex Nuts M4
Attenuation
Sheets
Optional Accessory
HT-120 Heating Unit
(4PH-XXXTA)
Accessories
Screws 4x20
Screws M4x30
U-Shaped
Brackets
Attenuation
Sheets
Optional Accessory
HT-200 Heating Unit
(4PH-XXXTAI)
)
Q'ty
8
8
2
Q'ty
8
8
4
2
Advertisement
Table of Contents
Related Manuals for Sengate 4PH-50TA
Summary of Contents for Sengate 4PH-50TA
- Page 1 50M/100M/200M QUAD PHOTOELECTRIC BEAM SENSOR TA TAI 4PH-50TA / 4PH100TA / 4PH-200TA INSTRUCTION MANUAL 4PH-50TAI / 4PH100TAI / 4PH-200TAI Thanks for purchasing product. Read this instruction manual before using the product to make sure that you u e it correctly.
- Page 2 NAMES OF FUNCTION SETTING SECTION Monitor - Alarm LED Monitor + SYNC Single (LED) 1.Weak Signal (LED) Beam Channel Switch Transmitter Power Switch Wiring Wiring 2. Master / Slave Switch Terminals Beam Channel Switch Terminals 2. Master / Slave Switch Response Time Adjustment 1.
- Page 3 WIRING DIAGRAM CH_B CH_A CH_A CH_B Master Master CH_A CH_B Slave-1 Slave-1 CH_A CH_B Slave-2 Slave-2 CH_A CH_B Slave-3 Slave-3 Control Panel Receiver Transmitter Transmitter Receiver T/T Sync Signal Power Alarm Signal INSTALLATION METHOD： 4PH-XXXTA 4-6 Refer to ″8. ALIGNMENT AND OPERATION ADJUSTMENT″...
- Page 4 BEAM CHANNEL CHANGEOVER FUNCTION & MASTER/SLAVE SWITCH： 5-1 When the existing range is shorter than product spec, then it only needs lower power for operation, please refer to Fig 5-1 for the setting. TRANSMITTER POWER SWITCH (TRANSMITTER) TRANSMITTER SYNC SIGNAL(LED) POWER SWITCH Model 4PH-50TAI 4PH-100TAI 4PH-200TAI...
- Page 5 FOUR TO FOUR When doing FOUR TO FOUR installation, refer to Fig 5-3, firstly, setting " Master " in position, the second third four units setting with Slave-1, Slave2 and Slave-3 sequentially. CH_A CH_B CH_B CH_A (Master) (Slave-1) (Drawing 4) (Slave-2) (Slave-3) TRANSMITTER...
- Page 6 RESPONSE TIME ADJUSTMENT： ● The beam interruption time adjustment is on Receiver Unit only. Speeds shown below are the maximum detectable speeds for each setting. Response time adjustment volume (ms) 50ms 100ms 300ms 500ms ( Receiver ) Running at full speed Running at slow speed Walking normally Walking slowly ※NOTE：In order to get the optimum setting for response time adjustment, operation testing is absolutely...
- Page 7 1. Channel (A-B) setting should be identical on both TX and RX. Operation 2. Wrong Channel setting. 2. Master Slave 1, 2, 3 setting on TX and RX should be identical. SPECIFICATIONS： Model No. Model No. 4PH-50TA 4PH-100TA 4PH-200TA 4PH-50TA 4PH-100TA 4PH-200TA Items...
- Page 8 2. Specifications and design are subjected to change without prior notice. 3. No take apart the product improperly, which possibly cause the damage. No.4-46, Fengren Rd., Renwu Dist., Kaohsiung City 81459, Taiwan (R.OC) Web Site : http : // www.sengate.com E-mail : service @ sengate.com TEL : +886-7-3721111~6...
Need help?
Do you have a question about the 4PH-50TA and is the answer not in the manual?
Questions and answers